LevelOne HVE-9006 User manual

HVE-9006
User Manual
HDMI Extender over CAT5e/6
CE marking is a certification mark that indicates conformity with health, safety, and
environmental protection standards for products sold within the European Economic
Area (EEA).The CE marking is also found on products sold outside the EEA that have
been manufactured to EEA standards. This makes the CE marking recognizable
worldwide even to people who are not familiar with the European Economic Area.
WEEE is waste electrical and electronic equipment. It is end-of-life electrical and
electronic equipment and covers virtually everything with a plug or battery. ... The
EC introduced the WEEE Directive in 2002 to address the environmental impacts of
unwanted electrical and electronic equipment at end-of-life disposal.

2
Introduction
The HVE-9006 extends HDMI signal between Transmitter and
Receiver over CATx cable. It supports 1080p@60Hz video signals up
to 50 m including embedded multi-channel audio and HDCP 1.4.
Built-in EDID make this product compatible with most display and source
device, to ensure HDMI transmission.
Advanced power design (PoC) allows this product to be powered at
Transmitter, and only one power supply is required. In addition, the
send/receive IR signals each other over the same CATx cable with IR pass
through.
Features
Supports HDMI 1.3, HDCP 1.4 compliant.
Supports built-in EDID to ensure HDMI signals transmission from
source to display.
The transmission of 1080p@60Hz (max) signal is up to 50 meter.
Supports bidirectional IR pass-through.
Supports PoC, the Receiver can be powered via Transmitter.
Package Contents

1 x HVE-9006T/R
1 x Power Adaptor (5V DC 1A)
1 x IR Kit
User Manual / QIG

3
Panel Description
Transmitter (TX)
①CAT OUT: RJ45 connector with Green& Yellow indicators. Connect to
Receiver over CATx cable.
The Green indicator lights up when powered on.
The Yellow indicator lights up when linked successfully between
Transmitter and Receiver.
②IR IN: Connect with IR Receiver.
③IR OUT: Connect with IR Emitter.
④DC 5V: Micro USB, connect to the power adaptor.
⑤HDMI IN: Connect to HDMI source.
⑥HDMI OUT: HDMI loop output, connect to display.
⑦RESET: Reboot.
Receiver (RX)
①CAT IN: RJ45 connector with Green& Yellow indicators. Connect to
Transmitter over CATx cable.
②IR IN: Connect with IR Receiver.
HDM I OUT
HDM I IN
DC 5V
IR OU TIR INCAT OUT
RES ET
1234567
EQ SE TTI NG
IR OU TIR INCAT IN
12345
HDM I OUT

4
③IR OUT: Connect with IR Emitter.
④HDMI OUT: Connect to display.
⑤EQ SETTING: After the system is connected, press this button three to
six times repeatedly until the best image output. When the cable, source,
or display is changed, or reset the output resolution, it is need to press this
button repeatedly to ensure the best image.
Specifications
Transmitter
Receiver
Input
(1) HDMI
(1) CAT
Input Connector
(1) 19-pin type-A female
HDMI
(1) RJ45
Output
(1) HDMI; (1) CAT
(1) HDMI
Output
Connector
(1) 19-pin type-A female
HDMI, (1) RJ45
(1) 19-pin type-A
female HDMI
Control
(1) IR IN, (1) IR OUT
(1) IR IN, (1) IR OUT
Control
Connector
(2) 3.5mm mini jacks
(2) 3.5mm mini jacks
General
Transmission
Distance
1080p@60Hz≤50m(CAT6)
HDMI Standard
HDMI 1.3, HDCP 1.4 compliant
EDID
Management
Built-in EDID

5
Power Supply
Input: 100VAC~240VAC, 50/60Hz; Output:
5VDC 1A
Power
Consumption
4W (Max)
Work
Temperature
-10~55℃
Relative Humility
10%-90%
Dimensions
(W*H*D)
66mm x 16.8 mm x66 mm
Weight
Transmitter: 36g; Receiver: 38g
Connection Diagram
Note: It is recommended to use CAT6 cable to ensure optimal transmission
distance.
DC 5V
Disp la yDVD
IR Emi tt er
IR Rec ei ve r Proj ec to r Remote IR Rec ei ve r DVD Re mo te
IR Emi tt er
Proj ec to r
PoC
P:
IR:
Catx
1080 P 55 m