LevelOne WRE-8011E User manual

LevelOne
WRE-8011E
AC1200 Wireless Range Extender
Quick Installation Guide
English Русский
Deutsch Italiano
Français Polski
Español Ελληνικά
Português

Table of Content
English ............................................................................................ 6
Deutsch .......................................................................................... 8
Français ........................................................................................ 10
Español ......................................................................................... 12
Português .................................................................................... 14
Русский ......................................................................................... 16
Italiano .......................................................................................... 18
Polski ............................................................................................. 20
Ελληνικά ...................................................................................... 22

1
LED Meaning
Your WRE-8011E has indicator lights on the
Top side. Please see below for an explanation
of the function of each indicator light.
Ethernet
On: Ethernet Connected
Flash: Transmit / Receive Data
Off: Ethernet Disconnected
Wireless
On: WLAN Ready
Flash: Transmit / Receive Data
Off: WLAN Off
Power
On: Power Ready
Flash: Waiting for device ready
Off: Power Off
WPS
Flash: Start WPS pairing within 2
minutes
Off: WPS Idle
WiFi Signal
On: Ethernet Connected
Flash: Transmit / Receive Data
Off: No WAN IP address from xDSL / Cable Modem
Connectors
Ethernet
Connects the device via LAN Ethernet to
a PC
WPS
Press this button for 3 full seconds and
the WPS LED will flash to start WPS.
Now go to the wireless adapter or device
and press its WPS button. Make sure to
press the button within 120 seconds (2
minutes) after pressing the router's WPS
button.
RESET
Reset button. RESET the WRE-8011E
to its default settings.
Press this button for at least 10 full
seconds to RESET device to its default
settings.
WPS button
Reset Button LAN Port

2
(Figure 1)
(Figure 2)
(Figure 3)

3
(Figure 4)
(Figure 5)

4
(Figure 6)
(Figure 7)
(Figure 8)

5
(Figure 9)
(Figure 10)
(Figure 11)
(Figure 12)

6
English
STEP 1 Connection of WiFi Range Extender
1. Connect the Ethernet cable to LAN Port
Connect the supplied RJ45 Ethernet cable from your PC's Ethernet
port to any of the WRE-8011E LAN Port.
2. Connect the WRE-8011E to your wall-mounted power outlet.
STEP 2 Configuration Procedures
Before starting the WRE-8011E configuration, please kindly configure the PC
computer as below, to have automatic IP address / DNS Server.
For Windows 10-32/64
1. Right click on Network icon , then click "Open Network and Sharing
Center" . (Figure 1)
2. In the Control Panel Home, click on “Change adapter settings” to
continue. (Figure 2)
3. Single RIGHT click on "Ethernet", then click "Properties".(Figure 3)
Double click on "Internet Protocol Version 4 (TCP/IPv4)". (Figure 4)
4. Check "Obtain an IP address automatically" and "Obtain DNS server
address automatically" then click on "OK" to continue.(Figure 5)
STEP 3 Quick Setup using the WPS Button
WPS Pairing between WRE-8011E and Wireless xDSL/Cable Modem. (Figure 6)
1. Press WPS button on Wireless xDSL/Cable Modem.
2. Press WPS button on WRE-8011E for 3 seconds and release WPS button.
Now the WPS LED is blinking and the WRE-8011E is donig WPS Pairing with
Wireless xDSL/Cable Modem.
Make sure to press the button within 120 seconds (2 minutes) after
pressing the Wireless xDSL/Cable Modem's WPS button.
3. Once the WRE-8011E finished doing WPS Pairing with Wireless xDSL/Cable
Modem, the Wifi Signal Strength LED is ON. The status of Wifi signal strength
LED varies depending on the Wifi signal strength between WRE-8011E and
Wireless xDSL/Cable Modem.
4. Check if the Wifi Signal Strength LED of WRE-8011E is ON, the WRE-8011E is
connected and suitable for Internet Connections.

7
5. Check if the Wifi Signal Strength is OFF, the WRE-8011E isn’t connected
and suitable for Internet Connections. Please repeat steps of WPS Pairing or
follow next step to have it connected and suitable for Internet Connections.
If the WRE-8011E WiFi signal strength LED isn't ON, please repeat steps of
WPS Pairing or configure the WRE-8011E through Advanced
Configuration below.
STEP 4 Advanced Configuration
From any of the LAN computers connected to , launch your web browser, type
the following URL in the web address (or location) box, and press [Enter] on
your keyboard:
http://repeater.nw
Repeater Mode (Extend your Wireless Network
1. Check on Select ratio of SSID of the front AP and click on Next>> button.
(Figure 7)
2. Please wait... 140 s. (Figure 8)
3. Enter Wifi password of the front AP and then click on Connect
button.(Figure 9)
AP Mode (Extend your Wired Network to allow wireless devices to connect
your wired network using Wi-Fi)
1. Check on TCP/IP Settings -> LAN SETTING from left menu. (Figure 10)
2. Select on Client from DHCP drop-down list.
3. Click on Save & Apply button. (Figure 11)
4. Click on Reboot Now button.
5. Change setting successfully! Do not turn off or reboot the Device during
this time. Please wait 20 seconds ... (Figure 12)
6. Please disconnect the Ethernet Cable from PC and connect it to the LAN
port of xDSL/Cable Modem.
7. Please wait for 2 minutes.
8. Now, the WRE-8011E has been configured completely, and suitable for
Internet Connections.