LevelOne FCS-3064 Instructions for use

Fixed Network Camera
Hardware User Manual
FCS-3064
Ver.2014/04/02

Hardware Manual
2
Table of Contents
Precautions.............................................................4
Safety Instructions .................................................................................... 6
Introduction.............................................................7
The List of Models..................................................................................... 7
Package Contents...................................................................................... 7
Physical Description ................................................................................. 8
Before Installation.................................................10
How to Connect DI/Do Devices............................................................... 10
How to Connect Audio Devices.............................................................. 13
Installing the Camera on a Surface.....................14
Step 1: Drill the Holes.............................................................................. 14
Step 2: Open the Dome Cover................................................................ 15
Step 3: Install the Camera to the Surface.............................................. 16
Step 4: Connect the Cable ...................................................................... 17
Step 5: Access the Camera Live View.................................................... 18
Step 6: Adjust the Viewing Angle and Focus ........................................ 18
Step 7: Close the Dome Cover................................................................ 18
Other Adjustments and Accessories ..................20
How to Adjust the Camera Viewing Angle and Focus .......................... 20
FCS-3064 Camera Models ................................................................... 20

Hardware Manual
3
How to Replace the Dome Cover............................................................ 21
How to Use a Memory Card .................................................................... 25
How to Insert the Memory Card............................................................ 25
How to Remove the Memory Card........................................................ 25
Accessing the Camera .........................................26
Configure the IP Addresses.................................................................... 26
Access the Camera.................................................................................. 30

Hardware Manual
4
Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to follow
the safety instruction given may directly endanger people, cause damage to the system or to
other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your local
office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.

Hardware Manual
5
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to the equipment that are not expressly approved by the
responsible party for compliance could void the user’s authority to operate the equipment.
European Community Compliance Statement
This product has been tested and found to comply with the limits for Class B
Information Technology Equipment according to European Standard EN 55022
and EN 55024. In a domestic environment, this product may cause radio interference in which
cause the user may be required to take adequate measures.

Hardware Manual
6
Safety Instructions
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may cause
hazards.
Do not use accessories not recommended by the manufacturer
Only install this device in a dry place protected from weather
Servicing
Do not attempt to service this video product yourself. Refer all servicing to qualified service
personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to qualified
service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the inner parts of video product have been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in this
manual. Adjust only those controls that are covered by the instruction manual, as an improper
adjustment of other controls may result in damage, and will often require extensive work by a
qualified technician to restore the video product to its normal operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.

Hardware Manual
7
Introduction
The List of Models
This hardware manual contains the following models:
FCS-3064
Fixed Dome Network Camera, 5-Megapixel, PoE 802.3af, Day & Night,
IR LEDs, WDR
From the installation perspective these models are very similar; therefore you can use one
manual for all of them.
Package Contents
Camera
Mounting Screw Kit
Hexagon Screwdriver
Terminal Block
(for Audio and DI/DO)
Drill Template
Quick Installation Guide
Drill Template

Hardware Manual
8
Physical Description
FCS-3064
NOTE: Actual camera may slightly differ.
1) Ethernet Port
Connects to a network using an Ethernet cable.
2) Memory Card Slot
Insert a memory card into this slot for local recording purposes. See How to Use a Memory Card
on page 25 for more information.
NOTE: Supports microSDHC and microSDXC cards.
3) Reset Button
The purpose of reset button is to restore the factory default settings of the camera, including
the administrator’s password.
The reset button can be used for following purposes:
The administrator’s password has been forgotten and therefore the camera cannot be
accessed.
1. In case of IP address, mask, or allow/deny filter related issues, resulting with inability to
modify these settings.
2. In case of connectivity issues or abnormal video quality.

Hardware Manual
9
How to do the reset properly?
Press and hold the reset button for 5 seconds.
4) Digital Input / Output (DI/DO) and Audio Input / Output
This connector connects to digital input or output devices, such as an alarm trigger, panic
button, etc., as well as audio input and output devices, such as microphones and speakers.
Digital Input (DI) and Digital Output (DO) devices are used in applications like motion
detection, event triggering, alarm notifications, etc. See How to Connect DI/Do Devices on
page 10 and How to Connect Audio Devices on page 13 for more information.

Hardware Manual
10
Before Installation
This section describes the procedures in preparing the external devices that you can connect to
the camera. Depending on your surveillance needs, you may connect digital input (DI) or digital
output (DO) or audio input / output devices to your camera. The camera comes with one (1)
terminal block for both digital and audio input / output devices. The use of these devices, however,
is optional.
How to Connect DI/Do Devices
Digital Input (DI) devices can be used to notify the camera about an activity in the camera site. DI
can be triggers of events. For example, you can connect a “panic button” to the camera; as such
when the panic button is pressed, the alarm signal will be sent through the camera. Other
common DI device applications are emergency button, smoke detector, passive infrared sensor,
etc.
Digital Output (DO) devices are external devices that are activated by the camera upon an event
inside the camera. For example, you can connect an “alarm horn” to the camera; as such when
an event occurs inside the camera (e.g. detected intruder), the alarm horn will sound. Other
common DO device applications are motion-triggered lights, electric fence, magnetic door locks,
etc.
Press and hold the orange tab as you insert the wire through the pin slot, then release the orange
tab to secure the wire.
To connect digital input / output devices (DI/DO), map the pins to one of the pin combinations
below:
Device
Pin
Mapping Instructions
Digital Output (DO)
DIO PW
Connect the wires of the output device to DIO PW and
DO.
DO
Digital Input (DI)
DIO GND
Connect the wires of the input device to DIO GND and
DI.
DI
For Audio Use

Hardware Manual
11
The table below shows the DI/DO connection specifications:
Device
DI
Connection design
TTL - compatible logic levels
Voltage
To trigger (low)
Logic level 0: 0V ~ 0.4V
Normal (high)
Logic level 1: 3.1V ~ 30V
Current
10mA ~ 100mA
DO
Connection design
Transistor (Open Collector)
Voltage & Current
< 24V DC, < 50mA
Typical Connection
Based on these specifications, if the DI device has a voltage of 0V ~ 30V or the DO device has a
voltage of < 24V (< 50mA), then the camera can supply internal power to these devices and there
is no need to connect the DI/DO device to an external power source.
In this case, wire the connection as below. Use the DIO GND and DI pins to connect a DI device
and use the DIO PW and DO pins to connect a DO device. See wiring scheme below:

Hardware Manual
12
High Voltage DO Device Connection
Even though the camera provides 12V power, this may not be enough for some high voltage DO
devices, such as a ceiling light or a motor that opens or closes a gate. In this case, there is a
need to connect an external relay. See wiring scheme below:
Note that when choosing an appropriate relay, please refer to its specifications and make sure
they match the above design. The triggering circuit voltage has to be around 12V DC and the
switch-controlled circuit voltage has to match the external power supply (e.g. 110V AC or 220V
AC).
The illustration below is a graphic example of connecting a relay to a high voltage DO device.
Relay
(DO1 Device)
)
Camera
Illuminator
110V-220V AC
External Power
Source
NOTE: For more information on DI/DO connections, please refer to the Knowledge Base
article on our website.

Hardware Manual
13
How to Connect Audio Devices
Audio input / output devices, such as an active microphone or speaker can be connected to the
camera using the supplied terminal block.
Press and hold the orange tab as you insert the wire through the pin slot, then release the orange
tab to secure the wire.
To connect audio devices, map the pins to one of the pin combinations below:
Device
Pin
Mapping Instructions
Audio Output (AO)
AO_GND
Connect the wires of the audio output device to
AO_GND and A_OUT.
A_OUT
Audio Input (A1)
AI_GND
Connect the wires of the audio input device to
AI_GND and A_IN.
A_IN
NOTE:For more information about AUDIO in connections, please refer to the Knowledge Base
article on our website.
For DI/DO Use

Hardware Manual
14
Installing the Camera on a Surface
This section describes the procedures in installing the camera on a flat surface such as a hard or
dropped ceiling and straight or tilted walls. Before installation, make sure the wall or the ceiling
can bear more than the weight of the camera.
NOTE: The camera images on the suceeding pages may slightly vary from the actual camera.
Step 1: Drill the Holes
Before drilling the holes on the ceiling or wall, note the direction of the connectors side of the
camera, which is also the opposite side of the camera logo. This influences the camera
placement and where you should drill the hole where the cables will pass through or how the
cables will go along the ceiling or wall.
1. Use the supplied drill template to mark the screw holes on the surface according to the
preferred orientation.
2. Determine how the cables will be routed: pass through the surface or along the surface.
If the cables will pass through the surface, drill the cable hole and the three (3)
screw holes on the surface.
If the cables will be routed along the surface, just drill the three (3) screw holes on
the surface.
3. Insert the plastic plugs into the screw holes.
Cable hole

Hardware Manual
15
Step 2: Open the Dome Cover
NOTE: To avoid scratches or leaving fingerprints on the dome cover, it is recommended to retain
the plastic covering the dome cover until the camera is completely installed.
1. With the bundled hex screwdriver, loosen the three (3) screws securing the dome cover.
2. Lift to remove the dome cover.
3. For D61A, D62A, E66A, E67A, remove the styrofoam covering the camera lens.

Hardware Manual
16
4. If the cables will be routed along the ceiling or wall, remove the cable tab from the dome
cover.
5. If the cables will pass through the ceiling or wall, route and pull the cables through the
hole on the surface.
Step 3: Install the Camera to the Surface
1. If necessary, insert a memory card, with the metallic contacts facing down, into the card slot
of the camera.
2. Align the camera screw holes and the cable hole (if necessary) to the holes on the surface
and attach the three (3) supplied screws to secure the camera.

Hardware Manual
17
CAUTION: When using electric screwdrivers, be careful not to touch the camera
components while attaching the screws. Since electric screwdrivers vary in sizes, speed, and
force, they may bruise and damage the camera components.
DISCLAIMER: LevelOne will not be responsible for camera damage caused by improper
installations or the misuse of equipment for installation.
Step 4: Connect the Cable
1. Connect the network cable to the Ethernet port of the camera. If necessary, connect other
cable connectors (optional), like audio input/output and DI/DO to the connector on the
camera. See Before Installation on page 10.
2. Connect the other end of the network cable to a switch or injector. Then, connect the switch
or injector to a network, PC and a power source. See Power-over-Ethernet (PoE) connection
example below.
Network
AC Power
Source
PoE Injector /
PoE Switch
Power Cable
Ethernet Cable
Ethernet Cable
(Data + Power)
Ethernet Cable
(Data)
Camera
Ethernet Port
Digital Input / Output (DI/DO)
and Audio Input / Output
Connector

Hardware Manual
18
Step 5: Access the Camera Live View
See Accessing the Camera on page 26 for more information on how to access the Live View of
the camera.
Step 6: Adjust the Viewing Angle and Focus
Based on the camera live view, adjust the viewing angle, orientation and focus of the camera.
Adjustments vary depending on model, see How to Adjust the Camera Viewing Angle and
Focus on page 20 for more information.
Step 7: Close the Dome Cover
1. Turn the dome cover shroud to align to the direction of the lens.
2. Align the screws with the screw holes of the camera. Note that if the cables are routed
along the ceiling or wall, route the cable to pass through the cable hole on the dome cover.

Hardware Manual
19
3. Tighten the three (3) screws to attach the dome cover to the camera body.
4. Remove the plastic covering the dome cover.
Final installation should look similar to the illustration below.

Hardware Manual
20
Other Adjustments and Accessories
How to Adjust the Camera Viewing Angle and Focus
This section describes procedures in adjusting the pan direction of the camera, as well as the
viewing angle and focus, if necessary since the camera comes with the focus and viewing angle
already pre-fixed.
FCS-3064 Camera Models
Camera Parts Overview
Adjustment Procedures
1
2
3
4