manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Lex
  6. •
  7. Power Distribution Unit
  8. •
  9. Lex PowerHOUSE Series User manual

Lex PowerHOUSE Series User manual

LM-PDU Rev. 002
PowerHOUSE
™
Power Distribution
Units (PDUs)
User Manual
Circuit Breakers
• Branch Rated
• Required with any receptacle with a
lower current rating than the Input
• Under lid or cover on some models
Feed Thru
• Female or Output Connector
• Same Type as Inlet
• No Overcurrent Protection
Step 1: Locating PDUs
-The PowerHOUSE™PDUs are designed to be used in indoor or outdoor locations
-Review labels attach to enclosure for rating
-‘TYPE 1’ indicates Indoor use only, ‘TYPE 3R’ indicates either Indoor or Outdoor use
-Each PowerHOUSE™ PDU should rest on its own base on a level surface with suitable ventilation
-DO NOT locate any PowerHOUSE™ PDU in any area prone to standing water
Step 2: Making and Breaking Connections on PDUs
WARNING:
– Before making or breaking connections to any PowerHOUSE™ PDU make certain the power source feeding
the system is OFF
– DO NOT exceed the voltage rating of the device as identied on the label attached to the enclosure
NOTE: If using the feed thru feature, connect the feed thru BEFORE the input connection is made
-Single-pole Cam Connectors
• When MAKING the connection, begin with the GREEN ground connection, then the WHITE neutral connection
and nish with the remaining HOT connections
• Firmly insert cam device into connector and rotate clockwise until fully engaged and locked
• When BREAKING the connection, begin with the HOT connections, then the WHITE neutral connection and
nish with the GREEN ground connection
-NEMA Locking Connector
• Fully insert the female connector into the male inlet
• Turn connector clockwise until it is fully locked
-LSC 19 Multi-pin Connector
• Align female connector with male inlet and insert, ensuring connection is fully seated
• Spin the locking collar of male inlet until snug
-NEMA Straight Blade Connections
• Fully insert the male plug into the female receptacle
Step 3: Powering Up PDUs
-Best practices dictate that loads are applied gradually the rst time the system is set up
NOTE: PowerHOUSE™PDUs are shipped with breakers in the ‘O/OFF’ position
1. Turn on the power source
2. Beginning with the PDU closest to the power source, move the rst individual circuit breaker to the ‘I/ON’
position
3. Ensure the devices fed by that circuit are ON, tracing the electrical path to the nal device fed by that circuit
4. Repeat steps 2 and 3 for the remaining circuit breakers
NOTE: If the circuit breaker cannot be energized or trips, check the system for continuity, short circuits and
overload, and make the necessary corrections before proceeding
The PowerHOUSE™ line of Power Distribution Units (PDUs) meet stringent requirements for either indoor or
outdoor site applications. This user manual reviews the proper use of the wide range of locking and non-locking
inlet, feed-thru and receptacle versions available. Please take time to review all precautions and warnings in the
manual prior to making the proper connections for use. Store this manual in a safe location for future reference.
Unpacking and Inspection
Before you begin your installation check the shipment carefully to conrm it arrived complete and undamaged.
1. Check the contents against the packing list to ensure the devices are the correct models
2. Check the unit for loose or broken components, which might have resulted from shipping
3. Inspect for signs of damage to wiring devices or circuit breakers
If there is any damage to the PowerHOUSE™ PDU, contact Lex Products toll free at (855) 539-1002 or email
[email protected].
PowerHOUSE™PDU Components (Typical)
Receptacles
• Female or Output Connector
• Shielded by Overcurrent Protection (Circuit Breaker)
Rubber Enclosure
• Non-conductive material
• Resistant to shock, impact and corrosion
Introduction Setting Up PowerHOUSE™ Power Distribution Units (PDUs)
Inlet
• Male or Input Connector
Indicator Lamps
• Denotes presence of input power
Lex Products
15 Progress Drive
Shelton CT 06484
203.363.3738
203.363.3742 Fax
Lex West
12701 Van Nuys Blvd.
Suite Q
Pacoima, CA 91331
818.768.4474
818.768.4040 Fax
www.lexproducts.com
[email protected]
800.643.4460
© Copyright Lex Products 2020
Produced in the United States of America
All Rights Reserved.
Lex Products logo and lexproducts.com are
trademarks or registered trademarks of Lex
Products in the United States,
other countries, or both.
If there is no power at receptacles:
1. Ensure that connections are in place and tight
2. Ensure that power source is live
a. Activate if not on
3. Ensure that circuit breakers are ‘I/ON’
4. If a circuit breaker trips, identify source of short circuit or overload and correct before resetting circuit breaker
a. Check to see if the circuit is overloaded and reduce loads as needed
b. Check for short circuits in the cabling or load device and correct as needed
5. For those receptacles that include a GFCIs:
a. Ensure the GFCIs are set by pressing the ‘RESET’ button
6. If a GFCI trips, identify source of current leakage and correct before resetting the GFCI
a. Check to see if the circuit is overloaded and reduce loads as needed
b. Check for short circuits in the cabling or load device and correct as needed
7. If there is still no power at receptacles:
a. Remove PDU from use
b. Contact Lex Products for next course of action
Technical Support
Lex Products is available to help answer any product related inquiries. For any questions or technical advice,
please call toll free 800-643-4460 or email [email protected].
Troubleshooting Guide

Other Lex Power Distribution Unit manuals

Lex PowerHOUSE Terrapin Station II User manual

Lex

Lex PowerHOUSE Terrapin Station II User manual

Lex Load Master User manual

Lex

Lex Load Master User manual

Popular Power Distribution Unit manuals by other brands

JAMO ZI-8 quick start guide

JAMO

JAMO ZI-8 quick start guide

Vimar ELVOX 46264.002 quick start guide

Vimar

Vimar ELVOX 46264.002 quick start guide

GE SPM Series instruction manual

GE

GE SPM Series instruction manual

ICM Controls ICM491 manual

ICM Controls

ICM Controls ICM491 manual

Dataprobe sBB-N15 Installation and operations

Dataprobe

Dataprobe sBB-N15 Installation and operations

Enlogic EN2101 Quick start installation guide

Enlogic

Enlogic EN2101 Quick start installation guide

ABB Relion REQ650 Commissioning manual

ABB

ABB Relion REQ650 Commissioning manual

Audioroot eSMART TRIO manual

Audioroot

Audioroot eSMART TRIO manual

BS 20 A Series instruction manual

BS

BS 20 A Series instruction manual

Ground Zero GZTC 1.0FX owner's manual

Ground Zero

Ground Zero GZTC 1.0FX owner's manual

Middle Atlantic Products Protection Series instruction sheet

Middle Atlantic Products

Middle Atlantic Products Protection Series instruction sheet

Remote Audio BDSv5 SMART manual

Remote Audio

Remote Audio BDSv5 SMART manual

nvent Schroff RackPower RP 2325 Wiring diagram

nvent

nvent Schroff RackPower RP 2325 Wiring diagram

Eaton Powerware Series user guide

Eaton

Eaton Powerware Series user guide

Altronix PDS8CB user manual

Altronix

Altronix PDS8CB user manual

EuroLite SBM-32 user manual

EuroLite

EuroLite SBM-32 user manual

TOWA LCM1010 Operation manual

TOWA

TOWA LCM1010 Operation manual

ATEN PG98230 Series user manual

ATEN

ATEN PG98230 Series user manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.