LG PMNFP14A0 User manual

ENGLISH
LG
PI485 for Outdoor Unit
INSTALLATION MANUAL
LG
IMPORTANT
• Please read this installation manual completely
before installing the product.
• Installation work must be performed in
accordance with the national wiring standards
by authorized personnel only.
• Please retain this installation manual for future
reference after reading it thoroughly.
Visit us at : http://www.lgservice.com
Models: PMNFP14A0
PMNFP14A1
PGNFP14A0
ITALIANO ESPAÑOL FRANÇAIS DEUTSCH CHINESE

2485 Gateway(M)
PI 485 INSTALLATION MANUAL
TABLE OF CONTENTS
■Safety Precautions.........................................................3~4
■Part Description .................................................................5
■Accessory Parts.................................................................6
■Installation Guide .........................................................7~11
■Installation Steps........................................................................................7
■DIP Switch Configuration...........................................................................8
■Simple Central Controller Connection Diagram........................................9
■PC / Deluxe Central Controller Connection Diagram ............................10
■How to connect the base station controller .............................................11

ENGLISH
Safety Precautions
Installation Manual 3
Don't touch with the
hands while the power is
on
•
There is risk of fire or electric
shock.
Use standard
parts(connector).
• Do not disassemble or repair
the product. There is risk of fire
or electric shock.
For electrical work, contact
the dealer, seller, a qualified
electrician, or an Authorized
Service Center.
• Do not disassemble or repair
the product. There is risk of fire
or electric shock.
■Installation
ON
L1 2 3 4
KSDO4H
ON
L1234
KSDO4H
ON
L1 2 3 4
KSDO4H
Safety Precautions
To prevent injury to the user or other people and property damage, the following instructions
must be followed.
■Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classified by the following indications.
■Meanings of symbols used in this manual are as shown below.
WARNING
CAUTION
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage.
Be sure not to do.
Be sure to follow the instruction.
WARNING

Safety Precautions
4485 Gateway(M)
When the product is soaked (flooded or
submerged), contact an Authorized Service
Center.
•There is risk of fire or electric shock.
Be cautious that water could not enter the
product.
•There is risk of fire, electric shock, or product
damage.
ON
L1 2 3 4
KSDO4H
ON
L12 3 4
KSDO4H
■Operation
Use the correctly rated
breaker or fuse.
•There is risk of fire or electric
shock.
Do not install, remove, or re-
install the unit by yourself
(customer).
•There is risk of fire, electric
shock, explosion, or injury.
For installation, always
contact the dealer or an
Authorized Service Center.
•There is risk of fire, electric
shock, explosion, or injury.
ON
L1 2 3 4
KSDO4H
ON
L1 2 3 4
KSDO4H
ON
L12 3 4
KSDO4H

ENGLISH
Part Description
Installation Manual 5
Part Description
PMNFP14A0 / PMNFP14A1 / PGNFP14A0
PI485 GATEWAY(M)
CN_PWR: AC 220V Connector
+10V: DC 10V Terminal
GND: Ground
BUS_A: *RS-485 (+) Terminal
(Refer to note)
BUS_B: RS-485 (-) Terminal
CN_OUT: Outdoor Unit Connector
LED1:RS-485 Status LED
DIP Switch: Product Selection (Refer to the DIP Switch Configuration )
LED01G, 02G, 03G: Communication Status LED
Reset Switch: PI485(M) Reset
CN_DRY: DRY Contact
ON
L1 2 3 4
KSDO4H
1
2
3
4
5
6
7
8
9
10
11
1
2
3
4
5
6
7
8
9
10
11
✽The location of parts might be different in case of PMNFP14A1.
PMNFP14A0 : For connecting 1 ~ 16 Indoor Units
PMNFP14A1 : For connecting 1 ~ 48 Indoor Units
PGNFP14A0 : For connecting only base controller
* Note : RS-485 is one of the international interface standards for serial communication.

Acceassory Parts
6485 Gateway(M)
Acceassory Parts
ON
L1 2 3 4
KSDO4H
PI485 : PMNFP14A0(1EA)
or PMNFP14A1(1EA)
or PGNFP14A0(1EA)
BRACKET (1EA)
Multi-V
Multi-V MPS Multi
WIRE ASSY 1(1EA)
SCREW (4EA)
WIRE ASSY 2(1EA) WIRE ASSY 3(1EA)
Others : Tie Wrap (3 EA) - Cable Tie
Clamp (1 EA)

Installation Guide
Installation Manual 7
ENGLISH
Installation Steps
1. Connect CN_OUT with Outdoor Unit by the cable (provided)
2. Connect RS-485 BUS_A(+) and BUS_(B)(-) with other network products (ex.
Central Controller , I-Gateway.....)
3. In case of using Simple Central Controller, connect VCC(+10V) and GND.
No need to connect otherwise.
4. Select DIP Switch Configuration(Refer page 8)
5. Connect CN_PWR with Outdoor PCB Power connector (Refer page 9, 10)
6. After Power is ON, check the Communication LED
- LED1G(Red)
•Normal : LED blinks for 5 times and then gets OFF
This process is repeated after every 3 minutes
•Error : Check the Indoor Unit's address & wiring connections
- LED2G(Yellow), LED3G(Orange)
•Normal : LED blinks continuously
•Error : Check the DIP Switch setting & wiring connections
7. Check RS-485 Communication Status LED:
•Normal : LED's blinks 2 times in every 10~30 seconds
•Error : Check the wiring connections
8. Finally if all of the above steps are OK, then tie the cables by tie wraps & clamp
Installation Guide
6
8
1
7
9
4
5
2
3
* Example about Multi V plus
CAUTION:
Install the PI485 on the Noise Filter in Multi V plus.
Install the PI485 after checking the hole for screw.

Installation Guide
8485 Gateway(M)
ON
L1 2 3 4
KSDO4H
ON KSDO 4H
ON KSDO4H
ON KSDO4H
ON KSDO4H
ON KSDO4H
ON KSDO4H
DIP Switch Configuration
Select Air
Conditioner Type Select Network
Type
* LGAP : LG Air conditioner Protocol
1 ON, All others OFF: Multi V products(Except CRUN products) or
Multi(Non-Inverter) Product applied Common PCB(Refer to
NOTE) or Multi(Inverter) Product + Central Controller(All
types) - Without LGAP
1 and 4 ON, All others OFF: Multi V products(Except CRUN products)
or Multi(Non-Inverter) Product applied Common PCB or
Multi(Inverter) Product + Central Controller(All types) - Using
LGAP
2 ON, All others OFF: Multi(Non-Inverter) Product
+ Centroller(All types) - Without LGAP
2 and 4 ON, All others OFF: Multi Non-Inverter Product
+ Central Controller(All Types) - Using LGAP
1,2,3,4 ON : Multi V CRUN Product
+ Central Controller(All types) - Using LGAP
Multi V & Multi(LGAP applied) products Configuration Methods
CAUTION:
The wrong setting of air-conditioner switch could cause malfunctioning.
Switch setting must be done carefully.
Push the Reset button after changing the Dip switch.
NOTE: Multi(Non-Inverter) Product applied Common PCB
PCB P/NO. : 6871A20917*
P/NO. : 6871A20918*
P/NO. : 6871A20910*
* Please refer the corresponding Central Controller installation manual if you want to know whether
your Central Controller is compatible with LGAP or not.

Installation Guide
Installation Manual 9
ENGLISH
ON
L1 2 3 4
KSDO4H
PI485
C
D
VCC
MAIN PCB
MAIN PCB
PI485
Control Box
GND
MAIN PCB
CN_CENTRAL
CN_CENTRAL
CN_OUT
Simple Central Controller - Connection Diagram
CAUTION:
After product installation, tie the cables with Clamps & Tie-Wraps provided.
Check the right connection of each BUS A and BUS B.

Installation Guide
10 485 Gateway(M)
ON
L1 2 3 4
KSDO4H
CNU PCB
BUS_A
BUS_A
BUS_B
BUS_B
LAN PORT
ABCD VCC GND
MULTI OUTDOOR TERMINAL BLOCK
CN_CENTRAL
Outdoor PCB
PC / Deluxe Central Controller
•In case of Multi V, either connect
PI485 to Multi V terminal block or
connect it directly to the CNU PCB
as shown here.
PC/ Deluxe Central Controller - Connection Diagram
CAUTION:
After product installation, tie the cables with Clamps & Tie-Wraps provided.
Check the right connection of each BUS A and BUS B.

Installation Guide
Installation Manual 11
ENGLISH
[Steps to connect]
*Note: See the PI 485 manual for the internal setting.
*Note: Because the RS485 communication line connecting to the PI 485 has polarity, check
A and B. PI485
How to connect the base station controller
•PGNFP14A0 (Only)
Connecting the PI 485 communication line
POWER
RUN/STOP RESETMODE
EREORRUN
Indoor unit #1 (Control address : 01)
Indoor unit #1 (Control address : 02)
Base station controller
AB
BUS_B
BUS_A
GND
10V
BUS_B
BUS_A
GND
10V
Aircon

Memo
12 485 Gateway(M)

P/No.: MFL37115809
After reading this manual, keep it in a place easily accessible to the user for future reference.
Printed in Korea