Life Gear 93810 User manual

Magnet Power, Elliptical Transorbit
OWNER’S MANUAL
Model# 93810

1
Table of Contents
2 ■Warranty
3 ■Precautions
4 ■Operation Instruction
5 ■Parts List
7 ■Overview Drawing
8 ■Hardware Packing List
9 ■Assembly Instructions
13 ■Adjustment
13 ■Maintenance and Treatment
14 ■Warm Up Exercises
The equipment conforms to EN957-1 and EN957-9 Class HC requirements.

2
One Year Limited Warranty
LifeGear Inc. warrants to the original purchaser that this product is free from defects in material
and workmanship when used for the purpose intended, under the conditions that it has been
installed and operated in accordance with LifeGear’s Owner’s Manual. LifeGear’s obligation
under this warranty is limited to replacing or repairing, free of charge, any parts which may prove
to be defective under normal home use. This warranty does not include any damage caused by
improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year. All
parts and workmanship, including electronics and its console cases, upholstery, foam, ball
bearings, pulleys, cables, shocks, all tension mechanisms, wheels, pedals and hardware are to
be free from defects for 90 days, This warranty is offered only to the original owner and is not
transferable. Proof of purchase is required. For customer service please call
1-800-226-4493.
Ordering Replacement Parts
Replacement parts can be ordered by calling or emailing our customer service department
[e-mail]
1-800-226-4493
Monday through Friday,
8:00 AM - 5:00 PM (PST).
When ordering replacement parts please have the following information ready:
1. Owner’s Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase
WARNING: Before beginning this or any exercise program, consult your physician. This is
especially important for people with pre-existing health problems.

3
1. Precautions
1) Read all the instructions in this manual and do warm up exercises before using this
equipment.
2) This elliptical bike is a home stationary fitness equipment, and also an aerobic training
equipment that can help you to develop your cardio-vascular function.
3) Please make sure all parts are not damaged and fixed well before use. The equipment should
be placed on a flat surface when using. Using a carpet or other covering material on the
ground is recommended.
4) Consult your physician and make a suitable exercise schedule before exercise. This is
particularly important to people who are over 35 years old or who have prior medical history.
In order to attain the ideal exercise result, besides executing a suitable amount of exercise, it
is also very important to insist on doing exercise every day.
5) Before exercise, in order to avoid injuring the muscle, warm-up exercise of every position of
the body is necessary. Refer to section 9 Warm Up Exercises. After exercise, relaxation of the
body is suggested for cool-down.
6) Keep children and pets away from the equipment while operating the equipment. This
machine is designed for adults only. The minimum free space required for safety operation is
39.4” x 47.3” x 78.8” in (100 x 120 x 200 cm).
7) Be careful when stepping on and off the pedals. Always hold the handlebars when stepping
off the equipment. Move the pedal you intend to mount on to its lowest position, step on the
pedal, and stride over the main frame to step on the other pedal. When using, please hold the
handlebar with your hands. To make the pedals run smoothly, push or pull handlebars, then
run the equipment regularly by cooperation of hands and feet. After exercise, please also
make one pedal at the lowest position and leave your foot on the higher pedal first and then
another.
8) Do not use this equipment one hour before or after dinner.
9) If you feel any chest pains, nausea, dizziness, or short of breath, you should stop exercising
immediately and consult your physician before continuing.
10)The maximum weight capacity of the user is 250 lbs/113 kgs.
11)The braking system of the equipment is speed-independent.
12)The equipment is designed according to EN957-1/9HC Regulations.
Warning: It will be harmful if you do not follow the above-mentioned precautions.

4
2. Operating Instruction
FUNCTIONS AND OPERATIONS:
AUTO ON/OFF: When you start to exercise or press the button on the
computer, the monitor will turn on. If you leave the equipment for 5 minutes,
the power will turn off automatically.
SCAN: Press the button until SCAN appears at SCAN position, monitor will
scan the following functions: time, speed, distance, calories and pulse
every 4 seconds.
TMR: Count exercise time from start to end.
SPD: Display current speed (mph).
DST: Count the distance from exercise start to end (mph).
CAL: Count the total calories from exercise start to end (Kcal).
ZERO CLEARING: Button being pressed over 4 seconds, all data returns to zero.
PULSE: Hold pulse sensors with hands and the screen will display your current heart beat rate in
beats per minute (BPM) after 4-5 seconds.“”means the pulse signal input.
REPLACING THE BATTERY: Open the battery cover and place two " AA " or "UM-3 " batteries
when the screen can not show clearly.
Note: The computer display can recover 15 seconds later after the battery replacement. Memory
data will all disappear after replacing the batteries.

5
3. Parts List
No. Description Qty No. Description Qty
1 Main frame 1 51 Ф8 Spring washer 16
2 Rear stabilizer 1 52 Ф5 Flat washer 1
3 Base foot 4 53 Ф8 Plastic flat washer 2
4 Pedal support tube 2 54 Ф10 Plastic flat washer 2
5 Pedal 2 55 Crosshead self lock bolt ST4.2x16 8
6L,R Handlebar support (left & right) 1 56 M6x50 Bolt 1
7 Nut cap 10 57 M5x50 Bolt 1
8 Left handlebar 1 58 M5 Nut 1
9 Arc spacer 2 59 M6 Nut 2
10 Computer 1 60 M10x1x5 Nut 4
11 Right handlebar 1 61 M10x1x3 Nut 2
12 Tension control wire 1 62 M12 Nut 1
13 Front stabilizer 1 63 M8 x20 Bolt 3
14 Front upright frame 1 64 Bearing set 1set
15 Handlebar bushing 4 65 Press-belt wheel 1
16 M8 Special washer 2 66 Spacer 1
17 M10 Special washer 8 67 Crank 1
18 Handlebar support bushing 4 68 Belt 1
19 Pedal bushing 4 69 M10 Nut 1
20 Hand pulse bar 1 70 Wheel bracket 1
21 Tension control 1 71 Wire clamp 1
22 Foam grip 2 72 Left cover 1
23 Adjustable base foot 2 73 Belt wheel 1
24 Pulse wire 2 74 Right cover 1
25 Sensor wire I 1 75 Pressing belt wheel spring 1
26 Computer wire 1 76 Magnetic spring 1
27 Sensor wire II 1 77 Sensor bracket 4
28 Ф20 Wave washer 2 78 Magnet axis 1
29 Round plug 2 79 Flywheel 1
30 Left pedal axis 1 80 Ф6 Flat washer 5
31 Right pedal axis 1 81 Crosshead self bolt ST2.9x8 2
32 Hand pulse tube 2 82 Crosshead bolt M4x16 4
33 M8×40 Bolt 4 83 Crosshead self bolt 4x16 4
34 M10×70 Bolt 2 84 M 6x8 Bolt 4

6
No. Description Qty No. Description Qty
35 M10×20 Bolt 2 85 Wheel axis 2
36 M8×16 Bolt 2 86 Wheel 2
37 M8×50 Bolt 4 87 U-shape bracket 2
38 M8×20 Bolt 10 88 Pulse sensor 2
39 M5x35 Screw 1 89 Round plug 2
40 M8 Cap nut 4 90 F35 Square tube plug 2
41 M10 Lock nut 6 91 Front connecting tube 1
42 M8 Lock nut 9 92 Crosshead self bolt ST4x25 2
43 1/2” Left lock nut 1 93 M8x16 Bolt 2
44 1/2” Right lock nut 1 94 M10x55 Bolt 2
45 Ф8 Arc washer 12 95 M6 Lock nut 1
46 Ф10 Flat washer 11 96 Ф16 Wave washer 2
47 Ф10 Spring washer 2 97 Rear U-shape bracket 2
48 Ф10 Big washer 4 98 M10x65 Bolt 1
49 Ф8 Big washer 2 99 Wrench 2
50 Ф8 Flat washer 12 100 Screw driver 1

7
4. Overview Drawing

8
5. Hardware Packing List

9
6. Assembly Instructions
Attention:
Please follow these assembly instructions step by step to assemble this elliptical.
1. Attach the Front Connecting Tube
Insert the Tension control wire (12) and Sensor wire I (25) into the bottom tube hole of Front
connecting tube (91) and then pull them out from the upper hole of Front connecting tube (91).
(See figure 1a)
Attach the Front connecting tube (91) to the Main frame (1) with three Bolts (63), Lock nuts (42),
and Flat washers (50). (See figure 1b)
2. Attach the Rear Stabilizer
Attach the Rear stabilizer (2) to the Main frame (1) with two Bolts (38), Spring washers (51),
and Flat washers (50). (See figure 2)
3. Attach the Front Stabilizer
Attach the Front stabilizer (13) to the Front connecting tube (91) with two Bolts (38), Spring
washers (51), and Flat washers (50). (See figure 3)