Life Gear CLASSIC PRO 20790 User manual

CLASSIC PRO
Magnetic Upright Bike
ITEM NO.: 20790
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo and are subject to change without
prior notice. 2017, Sept.

1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 2
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3
PARTS LIST ------------------------------------------------------------------------------- 4
HARDWARE AND COMPONENT LIST -------------------------------------------- 5
TOOLS -------------------------------------------------------------------------------------- 5
OVERVIEW DRAWING ----------------------------------------------------------------- 6
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 7
HOW TO MOVE THE UPRIGHT BIKE --------------------------------------------- 18
OPERATING THE COMPUTER ------------------------------------------------------ 19
ADJUSTMENTS -------------------------------------------------------------------------- 20
MAINTENANCE -------------------------------------------------------------------------- 21
TROUBLESHOOTING ------------------------------------------------------------------ 21
WARM UP AND COOL DOWN ROUTINE ----------------------------------------- 22

2
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is offered only to the original owner and is not transferable. Proof of
purchase is required.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

3
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following important
safety instructions when using this equipment. Read all instructions before using
this equipment.
1. Read all instructions and follow it carefully before using this equipment. Make sure the
equipment is properly assembled and tightened before use.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercises are
recommended.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes
that may catch any part of the equipment; remember to tighten the pedaling straps.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult your local dealer.
6. Do not use the equipment outdoors.
7. This equipment is for household use only. It is not a commercial model.
8. Only one person at a time should use this equipment.
9. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
10. Care should be taken in mounting or dismounting the equipment.
11. Do not allow children to use or play on the equipment. Keep children and pets away
from the equipment while in use. This machine is designed for adults use only. The
minimum free space required for safe operation is not less than two meters.
12. The maximum weight capacity for this product is 110 kgs.
WARNING: Before beginning any exercise program consult your
physician. This is especially important for the people who are over 35 years old or
who have pre-existing health problems. Read all instructions before using any
fitness equipment.
CAUTION: Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

4
PARTS LIST
No. Description Qty No. Description Qty
001 Rear Stabilizer End Cap 2 023 Cross Recessed Pan Head
Tapping Screw ST3.5x10 2
002 Carriage Bolt M8x75 4 024 Seat Sliding Tube 1
003 Rear Stabilizer Ø50x1.5tx480 1 025 Seat Cushion (DD98-2) 1
004 Curve Washer Ø8.5xØ18x1.5t 10 026 Handlebar Post Cover 1
005 Spring Washer Ø8.5xØ14x2.0t 12 027 Seat Sliding Tube End Cap
(38x38) 2
006 Cap Nut M8 4 028 Hexagon Socket Pan Head Cap
Bolt M8x15 6
007 Front Stabilizer Ø50x1.5tx330 1 029 Handlebar Post 1
008 Front Stabilizer End Cap 2 030 Washer Ø6.5xØ16 1
009 Hexagon Nut 7/8" 1 031 Cross Recessed Pan Head Bolt
M5x40 1
010 Main Frame 1 032 Tension Control Knob 1
011L Left Cover 1 033 Computer FB‐210 1
011R Right Cover 1 034 Cross Recessed Pan Head Bolt
M6x15 2
012L Left Foot Pedal (30X) 1 035 Handlebar Foam Grip
Ø23xØ29x550 2
012R Right Foot Pedal (30X) 1 036 Hand Pulse Sensor 2
013 Crank Cover 2 037 Hexagon Nut M10x1.0x3.0t 2
014 Cross Recessed Pan Head
Tapping Screw M4.2x20 12 038 Belt (PJ380) 1
015 Seat Post Bushing 1 039 Hexagon Socket Pan Head Cap
Bolt M8x25 2
016 Seat Post Knob M16 1 040 Hexagon Nut M6 2
017L Left Seat Sliding Tube Cover 1 041 Handlebar Ø25.4 1
017R Right Seat Sliding Tube Cover 1 042 Handlebar End Cap Ø25.4 2
018 Seat Post 1 043 Nut M10x1.0 2
019 Seat Adjustment Knob M8x40 1 044 Eyebolt M6x42 2
020 Washer Ø8.5xØ18x1.5t 8 045 Flywheel Ø250 1
021 Screw M4.2x20 4 046 Washer Ø25x3.0t 1
022 Hexagon Nylon Nut M8 5 047 Spring 1

5
PARTS LIST
HARDWARE AND COMPONENT LIST
TOOLS
No. Description Qty No. Description Qty
048 Idler Arm 1 057 Bearing Nut I 15/16” 1
049 Hand Pulse Sensor Wire (800 mm) 2 058 Seat Post Cover 1
050 Extension Sensor Wire (850 mm) 1 059 Washer Ø5xØ16x1.5t 2
051 Bolt M8x13 1 060 Tension Bracket 2
052 Idle Wheel Ø11xØ44x24 1 061 Ball Bearing 2
053 Sensor with Wire (700 mm) 1 062 Bearing Nut II 7/8” 1
054 Tension Cable (1150 mm) 1 063 Washer Ø23x3.0t 1
055 Bearing Cup 2 064 Spacer Ø8.5 xØ12x9 1
056 Belt Pulley with Crank 1
Allen Wrench with Phillips Screwdriver
1 PC
Multi Hex Tool
1 PC
(6) Cap Nut
4 PCS
(5) Spring Washer
4 PCS
(4) Curve Washer
4 PCS
(2) Carriage Bolt
4 PCS
(16) Seat Post Knob
1 PC

6
3
4
5
6
44
37
47
48
51
53
52
56
11R
21
13
12R
10
11L
12L
13
14
19
20
17L
23
22
17R
15
16
29
33
34 35
14
36
41 42
35
26
45
44
37
4
5
6
2
7
58
18
24
25
21
21
14
14
14
14
1
2
14 14 14
8
8
20
20
20
14
21
22
22
27
27
39
43
43
54
32
1
14
45
64
59
36
60
46
57
55
61
55
61
62
63
9
38
40
50
49
49
60
40
28
54
5428
5
20
30
31
32 50
14
59
4528
20
5
28
OVERVIEW DRAWING

7
ASSEMBLY INSTRUCTIONS
STEP 1
Position the Front Stabilizer (7) in front of the Main Frame (10) and align bolt holes.
Attach the Front Stabilizer (7) onto the front curve of the Main Frame (10) with two Carriage
Bolts (2), two Curve Washers (4), two Spring Washers (5), and two Cap Nuts (6). Tighten
cap nuts with the Multi Hex Tool provided.
Hardware:
7
4
5
6
10
2
2
6
5
4
4
5
6
7
2
(6) Cap Nut
2 PCS
(5) Spring Washer
2 PCS
(4) Curve Washer
2 PCS
(2) Carriage Bolt
2 PCS

8
2
3
10
4
5
6
6
5
4
2
3
6
5
4
2
STEP 2
Position the Rear Stabilizer (3) behind the Main Frame (10) and align bolt holes.
Attach the Rear Stabilizer (3) onto the rear curve of the Main Frame (10) with two Carriage
Bolts (2), two Curve Washers (4), two Spring Washers (5), and two Cap Nuts (6). Tighten
cap nuts with the Multi Hex Tool provided.
Hardware:
(6) Cap Nut
2 PCS
(5) Spring Washer
2 PCS
(4) Curve Washer
2 PCS
(2) Carriage Bolt
2 PCS

9
12R
12L
56
10
STEP 3
The Foot Pedals and Pedal Straps are marked “R” for Right and “L” for Left.
Select the Right Foot Pedal Strap (12R) which has R marked on the side of the strap. Snap
the two hole end of the strap onto the inside edge of the Right Foot Pedal (12R). Snap the
other end of the strap onto the outside edge of the Right Foot Pedal (12R). Select
adjustment holes which allow your foot to be easily removed from the foot pedal.
Use the same procedure to snap the Left Foot Pedal Strap (12L) onto the Left Foot Pedal
(12L).
STEP 4
Insert the pedal shaft of Left Foot Pedal (12L) into threaded hole in the left Crank (56). Turn
the pedal shaft by hand in the counter-clockwise direction until snug.
Note: DO NOT turn the pedal shaft in the clockwise direction, doing so will strip the
threads.
Tighten the pedal shaft of Left Foot Pedal (12L) with the Multi Hex Tool provided.
Insert pedal shaft of Right Foot Pedal (12R) into threaded hole in right Crank (56). Turn
the pedal shaft by hand in the clockwise direction until snug. Tighten pedal shaft of Right
Foot Pedal (12R) with the Multi Hex Tool provided.
Left Foot Pedal Right Foot Pedal
12R
12L

10
STEP 5
Remove three Hexagon Nylon Nuts (22) and three Washers (20) from underside of the Seat
Cushion (25). Remove hexagon nylon nuts with the Multi Hex Tool provided.
Guide bolts on underside of the Seat Cushion (25) through holes on top of the Seat Sliding
Tube (24), attach with three removed Hexagon Nylon Nuts (22) and three Washers (20).
Tighten hexagon nylon nuts with the Multi Hex Tool provided.
STEP 6
Remove one Spacer (64), one Washer (20) and one Seat Adjustment Knob (19) from
underside of the Seat Sliding Tube (24).
Guide the bolt on underside of the Seat Sliding Tube (24) through a hole on the top of the
Seat Post (18), attach with one removed Spacer (64), Washer (20) and Seat Adjustment
Knob (19).
25
20
22
20
22
25
24 20
22
24
19
20
64
19
20
18
64
24

11
STEP 7
Remove one Cross Recessed Pan Head Tapping Screw (14) from the Left/Right Seat
Sliding Tube Covers (17L, 17R). Remove screw with the Allen Wrench with Phillips
Screwdriver provided.
Attach both Left/Right Seat Sliding Tube Covers (17L, 17R) onto the top end of the Seat Post
(18) with one Cross Recessed Pan Head Tapping Screw (14) that was removed. Tighten
screw with the Allen Wrench with Phillips Screwdriver provided.
STEP 8
Slide the Seat Post Cover (58) onto the tube of the Main Frame (10).
Insert the Seat Post (18) into the tube of the Main Frame (10) at the desired height and then
attach the Seat Post Knob (16) onto the tube of the Main Frame (10) by turning it in a
clockwise direction to tighten the Seat Post (18) in the suitable position.
17L
14 17R
17L
14
17R
18
14
10
18
16
58
16
58
18
(16) Seat Post Knob
1 PC

12
STEP 9
Remove six Hexagon Socket Pan Head Cap Bolts (28), six Spring Washers (5), four Curve
Washers (4), and two Washers (20) from the Main Frame (10). Remove bolts with the Allen
Wrench with Phillips Screwdriver provided.
STEP 10
Slide the Handlebar Post Cover (26) up to the Handlebar Post (29).
28
5
20
4528
20
5
28
10
29
26
29
26

13
STEP 11
It is recommended to have a second person assist with this step. One person should hold
the Handlebar Post (29) in place while the other person to connect the wires.
Connect the Sensor Wire (53) from the Main Frame (10) to the Extension Sensor Wire (50)
from the Handlebar Post (29).
Put the cable end of resistance cable of Tension Control Knob (32) into the cable lock of
Tension Cable (54), see Figure A.
Pull the resistance cable of Tension Control Knob (32) up and force it into the slot of metal
bracket of Tension Cable (54), see Figure B.
Insert the metal fitting on the resistance cable of Tension Control Knob (32) into the hole at
the end of the slot in the metal bracket of Tension Cable (54), see Figure C.
Connect the resistance cable of Tension Control Knob (32) to Tension Cable (54) complete,
see Figure D.
A
B
C
D
50
53
53
50
10
54
54
54
54
54
32
32
32
32
29
26
32

14
STEP 12
Attach the Handlebar Post (29) to the Main Frame (10) with six Hexagon Socket Pan Head
Cap Bolts (28), six Spring Washers (5), four Curve Washers (4), and two Washers (20) that
were removed. Tighten bolts with the Allen Wrench with Phillips Screwdriver provided.
28
5
20
4528
20
5
28
10
29
26
4
5
28

15
STEP 13
Slide the Handlebar Post Cover (26) down to the Handlebar Post (29).
STEP 14
Remove two Curve Washer (4), two Spring Washers (5), and two Hexagon Socket Pan Head
Cap Bolts (39) from the Handlebar Post (29). Remove bolts with the Allen Wrench with
Phillips Screwdriver provided.
10
29
26
29
4
5
39
29

16
STEP 15
Insert the Hand Pulse Sensor Wires (49) from the Handlebar (41) into the hole on the
Handlebar Post (29) and then pull them out from the top end of the Handlebar Post (29).
STEP 16
Attach the Handlebar (41) onto the Handlebar Post (29) with two Curve Washer (4), two
Spring Washers (5), and two Hexagon Socket Pan Head Cap Bolts (39) that were removed.
Tighten bolts with the Allen Wrench with Phillips Screwdriver provided.
41
49
29
29
49
41
49
29
41
4
5
39

17
STEP 17
Remove two Cross Recessed Pan Head Bolts (34) from the Computer (33). Remove bolts
with the Allen Wrench with Phillips Screwdriver provided.
STEP 18
It is recommended to have a second person assist with this step. One person should hold
the Computer (33) in place while the other person to connect the wires.
Connect the Hand Pulse Sensor Wires (49) and Extension Sensor Wire (50) to the wires that
come from the Computer (33).
Attach the Computer (33) onto the top end of the Handlebar Post (29) with two Cross
Recessed Pan Head Bolts (34) that were removed. Tighten bolts with the Allen Wrench
with Phillips Screwdriver provided.
33
34
33
29
49
50
33
29
34

18
HOW TO MOVE THE UPRIGHT BIKE
This upright bike has a pair of Transport Wheels built into the front stabilizer and can be
carefully tilted onto its Transport Wheels for easy moving and storage.
To move the upright bike, firmly grasp the Handlebar with both hands. Next, carefully push
the upright bike down until it rolls freely on the Transport Wheels.
CAUTION: It is suggested you always use the aid of a second person when moving
the upright bike.
Handlebar
Transport Wheel

19
OPERATING THE COMPUTER
USING YOUR COMPUTER
The computer can be activated by pressing the MODE button or by
pedaling. If you leave the equipment idle for 4-5 minutes, the power
will turn off automatically.
BUTTON FUNCTIONS:
Press the MODE button to select the functions of the computer.
Press and hold the MODE button for 3 seconds to reset all data values to zero except the
ODO (ODOMETER) data values.
COMPUTER FUNCTIONS:
SCAN: Automatically scans each function in sequence with change every 4 seconds.
TMR (TIME): Displays your elapsed workout time in minutes and seconds.
SPD (SPEED): Displays the current training speed.
DST (DISTANCE): Displays the cumulative distance travelled during workout.
CAL (CALORIES): Displays approximate amount of calories burned during workout.
(This data is a rough guide for comparison of different exercise sessions and should not be
used in medical treatment).
ODO (ODOMETER): Displays the total accumulative distance travelled. The ODOMETER
data values can not be clear to zero by pressing and holding the button for 3 seconds. If
you take out the batteries from the computer, the ODOMETER data values will clear to zero.
P (PULSE): Displays your current heart rate figures after you grip the handlebar pulse
sensors with both your hands during exercise. To ensure the pulse readout is more precise,
please always hold on to the handlebar pulse sensors with two hands instead of just with
one hand only when you try to test your heart rate figures.
HOW TO INSTALL THE BATTERIES:
1. Remove the battery cover on the back of the computer.
2. Place two size AAA batteries into the battery housing.
3. Insure batteries are correctly positioned and battery springs are in proper contact with
batteries.
4. Re-install the battery cover.
5. If the display is illegible or only partial segment appears, remove batteries and wait 15
seconds before reinstalling.