Life Gear 76503 User manual

INCLINE BENCH
ITEM NO.: 76503
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo and are subject to change without
prior notice. 2020, Dec.

1
TABLE OF CONTENTS
WARRANTY -------------------------------------------------------------------------------- 2
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3
PARTS LIST ------------------------------------------------------------------------------- 4
HARDWARE PACK ---------------------------------------------------------------------- 5
EXPLODED VIEW ----------------------------------------------------------------------- 6
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 7
HOW TO MOVE THE INCLINE BENCH ------------------------------------------- 15
ADJUSTMENTS -------------------------------------------------------------------------- 16
MAINTENANCE -------------------------------------------------------------------------- 18
WARM UP AND COOL DOWN ROUTINE ----------------------------------------- 19

2
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is offered only to the original owner and is not transferable. Proof of
purchase is required.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

3
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions, including the following important safety instructions should always be
followed when using this incline bench. Read all instructions before using this incline
bench.
1. Read all instructions and follow it carefully before using this equipment. Make sure the
equipment is properly assembled and tightened prior to each use.
2. Before exercise, in order to avoid injuring the muscle, warm-up exercises are
recommended.
3. Please make sure all parts are not damaged and fixed well before use. This
equipment should be placed on a flat surface when using. Using a mat or other
covering material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment. Avoid wearing
loose clothing that may become entangled in the equipment.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult your local dealer.
6. Never drop or insert any object into any opening.
7. Do not use the equipment outdoors.
8. Do not jump on the equipment.
9. Doing all the exercises with a slow and controlled movement.
10. This equipment is for household use only. It is not a commercial model.
11. Only one person at a time should use this equipment.
12. Be careful to maintain your balance while using, mounting, dismounting, folding,
unfolding or assembling the equipment, loss of balance may result in a fall and serious
bodily injury.
13. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
14. Do not allow children to use or play on the equipment. Keep children and pets away
from the equipment while in use. This equipment is designed for adult use only. The
minimum free space required for safe operation is not less than two meters.
15. The maximum weight capacity for this product is 120 kg.
WARNING: Before beginning any exercise program consult your physician.
This is especially important for people who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness equipment.
Do not operate this exercise equipment without properly fitted guards, as the moving
parts can present a risk of serious injury if exposed.
CAUTION: Read all instructions carefully before operating this product. Retain
this Owner’s Manual for future reference.

4
PARTS LIST
No. Description Qty No. Description Qty
001 Front Stabilizer 1 026
Leg Developer Square End Cap
(□50) 2
002 Rear Stabilizer 1 027 Leg Developer Round End Cap Ø25 2
003
Front Tube
1 028 Round End Cap Ø25 6
004 Main Frame 1 029 Weight Holder Sleeve 1
005 Seat Support Tube 1 030 Small Spring Clip Ø25 1
006 Backrest Support Tube 2 031 Big Spring Clip Ø48 1
007 Incline Adjust Tube 1 032 Lock Pin Ø10x100 1
008 U-Shaped Bracket 1 033 Spacer Ø16xØ10.5x51.5 2
009 Adjustable Seat Bracket 1 034
Cross Recessed Pan Head Bolt
M6x15 2
010 Leg Developer 1 035
Cross Recessed Pan Head Bolt
M6x40 2
011 Arm Curl Tube 1 036
Hexagon Socket Pan Head Cap
Bolt M10x20 2
012 Holder Tube Ø25xT1.5x390 3 037
Hexagon Socket Pan Head Cap
Bolt M10x55 4
013
Backrest Adjustment Plate
500x45xT3.0 2 038
Hexagon Socket Pan Head Cap
Bolt M10x65 1
014 Seat 1 039
Hexagon Socket Pan Head Cap
Bolt M10x95 6
015 Backrest 1 040
Hexagon Socket Pan Head Cap
Bolt M10x150 3
016 Arm Curl Pad 1 041
Hexagon Socket Pan Head Cap
Bolt M8x40 8
017 Foam Roller Ø23xØ90x170 6 042
Hexagon Socket Pan Head Cap
Bolt M8x15 2
018 Adjustment Knob M16 2 043 Spring Washer M10 11
019 Round Bumper Ø25xØ9x12 2 044 Flat Washer Ø10 26
020 Hexagon Socket Set Screw M8x10 1 045 Flat Washer Ø8 10
021 Stabilizer End Cap 4 046 Flat Washer Ø6 2
022 Transport Wheel Ø50x25 2 047 Nylon Nut M10 10
023 Plastic Bushing Ø50xØ16.2 2 048 Nylon Nut M8 2
024
Arm Curl Tube Bushing
(□50x□38) 1 049
Axle Ø16xM10x71 1
025 Square End Cap (□25) 6 050 U-shaped Pin 1

5
HARDWARE PACK
STEP 1
(37) Hexagon Socket Pan
Head Cap Bolt 4 PCS
(39) Hexagon Socket Pan
Head Cap Bolt 2 PCS
(43) Spring Washer 6 PCS
(44) Flat Washer 8 PCS
(47) Nylon Nut 2 PCS
STEP 2
(36) Hexagon Socket Pan
Head Cap Bolt 2 PCS
(44) Flat Washer 2 PCS
(49) Axle 1 PC
STEP 3
(41) Hexagon Socket Pan
Head Cap Bolt 8 PCS
(42) Hexagon Socket Pan
Head Cap Bolt 2 PCS
(45) Flat Washer 10 PCS
Allen Wrench 5 mm 1 PC
Allen Wrench 6 mm 1 PC
Double Open End Wrench
13 mm-17 mm
1 PC
13 mm 17 mm

6
EXPLODED VIEW

7
ASSEMBLY INSTRUCTIONS
STEP 1
Attach the Front Tube (3) onto the Front Stabilizer (1) with two Hexagon Socket Pan Head
Cap Bolts (37), two Spring Washers (43), and two Flat Washers (44). Tighten bolt with the
6 mm Allen Wrench provided.
Hardware:
STEP 1
(37) Hexagon Socket Pan
Head Cap Bolt 2 PCS
(43) Spring Washer 2 PCS
(44) Flat Washer 2 PCS
6 mm Allen Wrench

8
STEP 1-1
Attach the Rear Stabilizer (2) onto the Main Frame (4) with two Hexagon Socket Pan Head
Cap Bolts (37), two Spring Washers (43), and two Flat Washers (44). Tighten bolt with the
6 mm Allen Wrench provided.
Hardware:
STEP 1
(37) Hexagon Socket Pan
Head Cap Bolt 2 PCS
(43) Spring Washer 2 PCS
(44) Flat Washer 2 PCS
6 mm Allen Wrench

9
STEP 1-2
Attach the Front Tube (3) onto the Main Frame (4) with two Hexagon Socket Pan Head
Cap Bolts (39), two Spring Washers (43), two Nylon Nuts (47), and four Flat Washers (44).
Tighten bolt and nylon nut with the 6 mm Allen Wrench and the Double Open End Wrench
provided.
Insert the Lock Pin (32) into the holes on the Adjustable Seat Bracket (9) and Main Frame (4)
to lock the Adjustable Seat Bracket (9) in place.
Hardware:
6 mm Allen Wrench
STEP 1
(39) Hexagon Socket Pan
Head Cap Bolt 2 PCS
(43) Spring Washer 2 PCS
(44) Flat Washer 4 PCS
(47) Nylon Nut 2 PCS

10
STEP 2
Remove two Hexagon Socket Pan Head Cap Bolts (36) and two Flat Washers (44) from the
both ends the Axle (49). Remove the bolt with the 6 mm Allen Wrench provided.
Insert the Axle (49) into the hole of the Leg Developer (10).
STEP 2-1
Position the Leg Developer (10) into the u-shaped bracket of the Main Frame (1) and align
bolt holes.
Attach the Leg Developer (10) with two Hexagon Socket Pan Head Cap Bolts (36) and two
Flat Washers (44) that were removed. Tighten bolt with the 6 mm Allen Wrench provided.
Hardware:
STEP 2
(36) Hexagon Socket Pan
Head Cap Bolt 2 PCS
(44) Flat Washer 2 PCS
(49) Axle 1 PC
6 mm Allen Wrench
6 mm Allen Wrench
STEP 2
(36) Hexagon Socket Pan
Head Cap Bolt 2 PCS
(44) Flat Washer 2 PCS
(49) Axle 1 PC
6 mm Allen Wrench

11
STEP 3
Attach the Seat (14) onto the Seat Support Tube (5) with four Hexagon Socket Pan Head
Cap Bolts (41) and four Flat Washers (45). Tighten bolt with the 5 mm Allen Wrench
provided.
Attach the Backrest (15) onto the Backrest Support Tubes (65) with four Hexagon Socket
Pan Head Cap Bolts (41) and four Flat Washers (45). Tighten bolt with the 5 mm Allen
Wrench provided.
Hardware:
STEP 3
(41) Hexagon Socket Pan
Head Cap Bolt 8 PCS
(45) Flat Washer 8 PCS
5 mm Allen Wrench

12
STEP 3-1
Attach the Arm Curl Pad (16) onto the Arm Curl Tube (11) with two Hexagon Socket Pan
Head Cap Bolts (42) and two Flat Washers (45). Tighten bolt with the 5 mm Allen Wrench
provided.
STEP 3-2
Turn the Adjustment Knob (18) in a counterclockwise direction until it can be pulled out.
Pull out the Adjustment Knob (18) and then insert the Arm Curl Tube (11) into the square
hole of the Main Frame (4). Slide the Arm Curl Tube (11) up or down direction to the
suitable position. Lock the Arm Curl Tube (11) in place by releasing the Adjustment Knob
(18) and sliding the Arm Curl Tube (11) up or down slightly until the Adjustment Knob (18)
"pops" down into the locked position. For added safety, tighten the Adjustment Knob (18) in
a clockwise direction.
STEP 3
(42) Hexagon Socket Pan
Head Cap Bolt 2 PCS
(45) Flat Washer 2 PCS
5 mm Allen Wrench

13
STEP 4
Slide a Foam Roller (17) onto one end of the Holder Tube (12). Insert the Holder Tube (12)
into the hole in the Main Frame (3). Slide the other Foam Roller (7) onto the other end of
the Holder Tube (12).
Press both Round End Caps (28) into both ends of the Holder Tube (12).
Slide a Foam Roller (17) onto one end of the Holder Tube (12). Insert the Holder Tube (12)
into the top hole in the Leg Developer (10). Slide the other Foam Roller (7) onto the other
end of the Holder Tube (12).
Press both Round End Caps (28) into both ends of the Holder Tube (12).
Slide a Foam Roller (17) onto one end of the Holder Tube (12). Insert the Holder Tube (12)
into the bottom hole in the Leg Developer (10). Slide the other Foam Roller (7) onto the
other end of the Holder Tube (12).
Press both Round End Caps (28) into both ends of the Holder Tube (12).

14
STEP 5
Attach the Small Spring Clip (30) to the Leg Developer (10).
Remove the Hexagon Socket Set Screw (20) from the Weight Holder Sleeve (29).
Remove screw with the Allen Wrench provided.
Slide the Weight Holder Sleeve (29) onto the Leg Developer (10) and secure with one
Hexagon Socket Set Screw (20) that was removed. Tighten screw with the Allen Wrench
provided.
Attach the Big Spring Clip (31) to the Weight Holder Sleeve (29).
Use the U-shaped Pin (50) to lock the Leg Developer (10) in place.

15
HOW TO MOVE THE INCLINE BENCH
This incline bench has a pair of Transport Wheels on the rear stabilizer and can be carefully
tilted onto its Transport Wheels for easy moving and storage. To move the bench, firmly
grasp the Leg Developer with both hands and the Leg Developer must be locked by
U-shaped Pin. Next, carefully pull the bench up until it rolls freely on the Transport Wheels.
CAUTION: It is suggested you always use the aid of a second person when moving
the bench.
Transport Wheel
Leg Developer
U-shaped Pin

16
ADJUSTMENTS
Adjusting the Adjustable Leveler
Turn the adjustable leveler on the front or rear stabilizer as needed to level the bench.
Adjusting the Backrest
The backrest can be adjusted according to your own training needs. Turn the adjustment
knob in a counterclockwise direction until it can be pulled out. Pull out the adjustment knob
and then raise or lower the backrest to the suitable position. Lock the backrest in place by
releasing the adjustment knob and raise or lower the backrest slightly until the adjustment
knob "pops" down into the locked position. For added safety, tighten the adjustment knob
in a clockwise direction.
Adjustable Leveler
Adjustment Knob
Backrest

17
Adjustment Knob
Arm Curl Pad
Adjusting the Arm Curl Pad Height
The arm curl pad height can be adjusted according to your own training needs. Turn the
Adjustment knob in a counterclockwise direction until it can be pulled out. Pull out the
adjustment knob and then slide the arm curl pad up or down direction to the suitable position.
Lock the arm curl pad in place by releasing the adjustment knob and sliding the arm curl pad
up or down slightly until the adjustment knob "pops" down into the locked position. For
added safety, tighten the adjustment knob in a clockwise direction.
Adjusting the Seat Height
The seat can be adjusted according to your own training needs. Pull out the lock pin and
then adjust the seat to the desired height, insert the lock pin back into the holes on the
adjustable seat bracket and main frame to lock the seat in place.
Lock Pin
Seat

18
U-shaped Pin
Leg Developer
Adjusting the Leg Developer
The leg developer can be locked when doing sit up exercise. Simply pull the U-shaped pin
out and drop into the hole on the leg developer. Remove the U-shaped pin when doing leg
developer exercises.
MAINTENANCE
The equipment can be cleaned using a clean and dry cloth after each use.
Upholstery can be cleaned with a mild detergent or spray cleaner.
Please inspect all assembly bolts and nuts on the equipment for proper tightness and frame
of the equipment for any sign of cracking or permanent bending. If you find this situation,
do not use this equipment and contact local dealer immediately.

19
WARM UP AND COOL DOWN ROUTINE
The WARM-UP is an important part of any workout. The purpose of warming up is to
prepare your body for exercise and to minimize injuries. Warm up for two to five minutes
before aerobic exercising. It should begin every session to prepare your body for more
strenuous exercise by heating up and stretching your muscles, increasing your circulation
and pulse rate, and delivering more oxygen to your muscles.
COOL DOWN at the end of your workout, repeat these exercises to reduce soreness in tired
muscles. The purpose of cooling down is to return the body to its resting state at the end of
each exercise session. A proper cool-down slowly lowers your heart rate and allows blood
to return to the heart.
HEAD ROLLS
Rotate your head to the right for one count, you should feel a
stretching sensation up the left side of your neck. Then rotate your
head back for one count, stretching your chin to the ceiling and
letting your mouth open. Rotate your head to the left for one count,
then drop your head to your chest for one count.
SHOULDER LIFTS
Lift your right shoulder toward your ear for one count. Then lift your
left shoulder up for one count as you lower your right shoulder.
SIDE STRETCHES
Open your arms to the side and lift them until they are over your head.
Reach your right arm as far toward the ceiling as you can for one
count. Repeat this action with your left arm.