Life Smart LS-1000X-6W Quick start guide

!"
OWNERS INSTA
OWNERS INSTALLATION AND OPERATING MANUAL LLATION AND OPERATING MANUAL
LIFESMART INFRARED HEATER
Model: LS-1000X-6W
"!"#$%&'()%*+$'
Please read this entire Installation and Operating Manual BEFORE installing and using
your new Infrared Heater. Failure to fully understand and follow instructions may result in
property damage, bodily injury, or even death.
"
If the Infrared Heater in not used properly, a house fire may result. For everyone’s safety,
FOLLOW all Installation and Operating Directions.
Save These Instructions

#"
TABLE OF CONTENTS
Topic Page(s)
Customer Service & Support 3
Introduction & Specifications 4
Important Safety Information 5-7
Frequently Asked Questions 8-11
Heater Operation 12
Heater Placement 13
Users Guide 14-15
Air Filter Maintenance 16
Warranty 17-19
*Contents in the box:
1. Infrared heater(1unit)
2. Instruction manual(1pcs)
$% Remote Control (2 AAA batteries not included)(1pcs)"
"
"

$"
Customer Service and Support
To Obtain Warranty Support or Advice, Please Complete These Easy Steps:
Contact LIFESMART PRODUCTS Technical Support
,-).$:1-866-484-2066 or 1-214-614-2509
/01"*2:[e-mail]
Visit us: www.lifesmartproducts.com
You will need to provide the unit's model number, serial number (located on the
heater’s front panel, rear panel, or on the box), date of purchase, retailer of purchase,
a daytime phone number, and possibly a copy of your receipt.
Be Patient, Clear, and Concise.
Describe the issue and symptoms you have for, and about the product. A certified
LIFESMART Technical Support agent will give you an evaluation of your issue and your
resolution options. If the answer is not available at that time, you will be referred to the
appropriate channels, or given a call/e-mail back within 72 hours with an answer or
resolution.
If after speaking with LIFESMART Technical Support, it is determined by one of our
agents that your unit may need to be sent in to us to be evaluated/repaired, our
representative will provide you with a reference number and provide you with details
on how to send in your unit for repair.

&"
INTRODUCTION
Thank you for choosing one of the best Infrared distribution heaters available on the market
today. Our Infrared Heater is a very safe and effective room heater. It produces safe, clean and
economical heat by utilizing quartz infrared heating elements. The heating process of the
Infrared Heater is similar to the way the sun warms the earth. The infrared elements warm the
heat chamber and the whisper quiet fan distributes the accumulated warmth. This process is
unique among heaters in that it minimizes wasteful heat collection at the ceiling height of rooms
and targets it toward the living space instead. Thank you for being our customer, and enjoy your
heater!
Our Infrared Heaters have been tested and listed for installation in residential and mobile homes
by ETL:
3189533
Conforms to UL STD. UL1278
Certified to CSA STD. C22.2 NO.46

'"
SPECIFICATIONS
Electrical:
Voltage: 120V~60Hz
Power consumption: Up to 1500 Watts
Thermostat range: 50-90 Fahrenheit
Dimensions:
14” x 12.7” x 17.6”, 25.5lbs
SAFETY FEATURES
Tip-Over Safety Feature
()*+"),-.,/"*+",01*22,3"4*.)"-".*2567,/"+-8,.9"8,-.1/,%":;<,".),"),-.,/"*+".*22,3"67,/="-;"*;.,/;->"+4*.<)"4*>>"
-1.6?-.*<->>9"+)1.".),"),-.,/"688%":;<,".),"),-.,/"*+"/,+.6/,3"-;"12/*@)."26+*.*6;=".),"),-.,/"4*>>"/,+,.%"(6"
<6;.*;1,"62,/-.*6;=".1/;"6;".),"),-.,/"1+*;@".),"+122>*,3"/,?6.,"<6;./6>"6/".),"<6;./6>"2-;,>"6;".),"),-.,/%"
Overheat Safety Feature
()*+"),-.,/"*+",01*22,3"4*.)"-"67,/),-."+-8,.9"8,-.1/,%"A),;".),"),-.,/+"*;.,/;->"<6?26;,;.+"/,-<)"-"<,/.-*;"
.,?2,/-.1/,".)-."<61>3"<-1+,"67,/),-."-;3"26++*B>,"8*/,=".),"),-.,/"4*>>"-1.6?-.*<->>9"+)1."688%"
"
GROUNDING INSTRUCTIONS
"
"
WARNING: ()*+"),-.,/")-+"-"76>.-@,"/-.*;@"68"!#C"
76>.+%"(),"<6/3")-+"-"2>1@"-+"+)64;"*;"D%"D;"-3-2.,/"-+"
+)64;"*;"E"*+"-7-*>-B>,"86/"<6;;,<.*;@".)/,,5B>-3,"
@/61;3*;@5.92,"2>1@+".6".465+>6."/,<,2.-<>,+%"(),"
@/61;3*;@">1@",F.,;3*;@"8/6?".),"-3-2.,/"?1+."B,"
<6;;,<.,3".6"-"2,/?-;,;."@/61;3"+1<)"-+"-"2/62,/>9"
@/61;3,3"61.>,."B6F%"(),"-3-2.,/"+)61>3";6."B,"1+,3"*8"
-".)/,,5+>6."@/61;3,3"/,<,2.-<>,"*+"-7-*>-B>,%"
"
G:"H:("GIJID("(KI"LDJI(M"NOPN:LI":J"(KI"
QP:OHGIG"NROQ%"
WARNING:"S."*+";6/?->"86/".),"264,/"<6/3".6"8,,>"4-/?".6".),".61<)T")64,7,/=".),"264,/"<6/3"
2/6;@+"?1+."B,".*@)."-;3"+,<1/,".6".),"4->>"61.>,.%"D">66+,"8*."B,.4,,;".),"61.>,."-;3".),"2>1@"?-9"
<-1+,",F<,++"),-."6/"67,/),-.*;@"68".),"2>1@"6/"<6/3%"S8".)*+"6<<1/+="./9"*;+,/.*;@".),"2>1@"*;.6"-"3*88,/,;."
61.>,.%"E6;.-<."-"01->*8*,3",>,<./*<*-;".6"*;+2,<.".),"6/*@*;->"61.>,."86/"3-?-@,"6/",F<,++*7,"4,-/%"

U"
34,5678(7'!89/7:'3(!76;<735(!'
6/8='8(=';(=/6!78(='8>>'3(!76;<735(!?'!89/7:'@86(3(A!?'
8(='98BCD'E/956/';!3(A'7F/'F/87/6'
WARNING!
G',57/(738>'956'/>/<763<8>'F8H86='39'(57'8=F/6/='75G'
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electric shock, and injury to persons, including the following:
1. This heater must be plugged into a 120V, 15 amp (or more) circuit of its own. Nothing
else can be plugged into the same circuit. If unsure if your home meets this
specification, consult a certified electrician prior to use. Risk of fire, overheat,
malfunction, property damage, injury, or even death may result if not adhered
to!
2. Connect to a properly grounded, 3-prong outlet only. Do not connect the heater to
extension cords, surge protectors, timers, direct breakers, or an outlet with other
appliances connected to the same outlet. Risk of fire, overheat, malfunction,
property damage, injury, or even death may result if not adhered to!
3. This heater is hot when in use. To avoid burns, do not let bare skin touch hot
surfaces. Use handles (certain models) or wheels to move this heater.
4. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and
curtains from the front of the heater and keep them away from the sides and rear of
the heater.
5. Extreme caution is necessary when any heater is used by or near children, invalids,
pets, or when the heater is left operating unattended.
6. Always unplug the heater when not in use.
7. Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped, or damaged in any manner. Contact the
manufacturer for resolution options.
8. Do not use outdoors. Exposure to outdoor elements such as rain, snow, sun, wind or
extreme temperatures may cause the heater to become a safety hazard.

V"
9. This heater is not intended for use in bathrooms, laundry areas and similar indoor
locations, nor any locations that use GFCI outlets.
10.Never place heater where it may fall into a bathtub or other water receptacles.
11.Do not run cord under carpet. Do not cover cord with throw rugs, runners, or similar
coverings. Arrange cord away from traffic area and where it will not be tripped over.
12.The heater must be plugged into a wall outlet that is a DEDICATED CIRCUIT, with a
minimum 15 amp rating on that individual circuit.
13.To disconnect the heater: FIRST, turn the power button to the “off” position, then
remove plug from the wall outlet.
14.To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not
use on soft surfaces, like a bed, where openings may become blocked.
15.Do not allow foreign objects to enter or block any ventilation or exhaust opening as
this may cause an electric shock or fire, or damage the heater.
16.Allow at least 3 feet of unobstructed space to the front and rear of the heater to allow
for maximum heat, air, and ventilation flow.
17.A heater has hot and arcing or sparking parts inside. Do not use it in areas where
gasoline, paint, or flammable liquids are used or stored, nor use flammable solvents to
clean the heater. Also, make sure to keep heater dry at all times.
18.Use this heater only as described in this manual. Any other use not recommended by
the manufacturer may cause fire, electric shock, or injury to persons.
19.Do not use abrasive solvents to clean the heater as it may cause damage to the finish
or casing.
SAVE THESE INSTRUCTIONS
PLEASE REVIEW FREQUENTLY ASKED QUESTIONS ON THE NEXT
FEW PAGES PRIOR TO USING YOUR HEATER.

W"
FREQUENTLY ASKED QUESTIONS (FAQ’S)
!"#$%&'%(#%)*'+#&#,+'(&-.%/#010(#2$%-#3#4*(+'#05%-#'$%#60782$%-#3#'9(-#'$%#$%&'%(#0-#40(#'$%#4*(+'#
'*)%:#;$"#*+#'$*+#$&55%-*-.<#
This is normal. This heater is treated with a special heat safe/resistant coating. This odor will sometimes
be present when the box is opened, and may be compared to a heaters version of “new car smell.” Also,
similar to all hearth appliances (woodstoves, etc.), the coating, exposed to heat, will produce this particular
odor during the first few hours of operation. This will dissipate after the break-in period. If you are sensitive
to odors, you may want to pre-burn the unit in a garage with the door open until the initial odor
dissipates.
34#)"#$%&'%(#(9-+#0-#&55(07*)&'%=">?@@#;&''+A#$02#)&-"#BCDE+#*+#'$&'<#3+#'$&'#&#=0'#04#$%&'<#
At 1500 Watts, your heater will use approximately 5100 BTUs. 5100 BTUs, compared to your home furnace,
is a very small amount of heat (this heater is intended to be used as supplemental heat in areas most
needed). It may take several minutes, to several hours to heat your area, depending on various factors (see
Heater Placement).
F&-#)"#$%&'%(#(%&=="#05%(&'%#0-#=%++#)0-%"#5%(#1&"<#;$&'#&(%#)"#05%(&'*-.#G0+'+<#
H%+:#If the heater is used as it is intended (as supplement/assist heat), it should cycle on and off, allowing for
it to heat a total of approximately 8 out of the 24 hours of the day. Using the national average of
approximately 10¢ per kWh (look at your bill for exact cost per kWh--will vary per state), your average
heating cost (add a few cents just for having it plugged in) should be less per day compared to your main
furnace. The costs will increase if it is used as the single source of heat, or if heat somehow escapes the
room being heated, since the “on” cycle will run longer.
The Formula: To determine the cost of this or ANY 1500 watt appliance, multiply 1.5 X your cost per
Kilowatt Hour to determine approximately how much it costs you to run the heater. You can find the cost per
KWH prices for your state at: http://www.eia.doe.gov/fuelelectric.html
F&-#'$%#$%&'*-.#%=%)%-'+#6%#(%5=&G%1<#
If after speaking to a LIFESMART Technical Support Agent, it is determined that heating elements have
failed. Heating elements may be replaced by obtaining them from the Manufacturer. All parts may be
purchased through LIFESMART if your product is out of warranty. Note: If you feel that the elements are
definitely faulty right out of the box, contact the LIFESMART Technical Support department first (for
troubleshooting and verification).They can then direct you on to the next step.

X"
I-G%#3#5=9.#'$%#9-*'#*-#&-1#'9(-#*'#0-A#$02#=0-.#2*==#*'#'&J%#'0#$%&'#)"#(00)<#
The heating process in the heater begins immediately upon powering on, and setting the desired
temperature above the ambient temperature. A noticeable change in the l room’s ambient temperature will
vary. Remember that with any type of heating process, there are many variables: Location of heater (in the
home), floor plan and size of the room, how well the room is insulated, how many doors/windows, how much
bare concrete (acts as a heat sink with any type of heating), the opening and closing of an exterior door,
long hallways, high ceilings, etc. Customers with smaller rooms experience quick heat changes. Rooms with
larger and open floor plans can expect up to 24 hours to completely heat up.
3#10-E'#$&K%#&#.(09-1%1#09'=%'L#G&-#3#9+%#&1&5'%(+A#&#MN5(0-.#502%(#+'(*5A#0(#(%)0K%#'$%#.(09-1#
5(0-.#4(0)#'$%#G0(1<#
Definitely NOT! If you don’t have a grounded outlet, contact a certified electrician for advice. Removing or
altering any part of the heater’s original design or intent (including the power cord) will not only void the
warranty, but will make you liable for any unexpected or hazardous results.
;$"#10%+-E'#'$%#'%)5%(&'9(%#0-#)"#$%&'%(#)&'G$#'$%#'%)5%(&'9(%#1*+5=&"#0-#)"#2&==A#0(#%7'%(-&=#'$%()0+'&'<#
This is completely normal. The temperature display on your heater may vary from the temperature display
on another thermostat (like the one mounted to your wall or a purchased external thermostat). This is
because the temperature sensor on the heater reads the temperature directly around the heater. With the
heater near the cold floor (and heat rising), any readings on elevated or external thermostats will differ in
readings on the heater. The best way to operate your heater is just to set the unit on “High” and dial up to a
temperature that feels comfortable to you. Then, leave it at that temperature, regardless of the mismatch.
The heater will cycle off when the set temperature is met or exceeded slightly.
!"#$0)%#*+#-0'#*-+9=&'%1#K%("#2%==:#F&-#3#9+%#'$%#$%&'%(#*4#3#$&K%#K&9='%1#0(#G&'$%1(&=#G%*=*-.+<#3#=*K%#*-#&#+'(9G'9(%#
'$&'#*+#=&(.%(#'$&-#>@@@#+O9&(%#4%%':#;*==#'$*+#$%&'%(#$%=5#)%< F&-#3#9+%#'$%#$%&'%(#'0#$%&'#)9='*5=%#(00)+#&'#'$%#
+&)%#'*)%<#;*==#3#6%#&6=%#'0#9+%#'$%#$%&'%(#*-#&#6&+%)%-'#0(#.&(&.%<#
The answer to these is the same. Yes. You will be able to use it, but keep in mind that rooms/structures with
open floor plans, minimal insulation, adjacent rooms, or high ceilings will not retain the heat as efficiently,
and noticeable heat changes will come slowly. Also, the heater will stay on for longer periods of time (since it
takes so long to cycle off), and may increase your electric costs. Note that if you do use it in a garage or
basement, the moisture levels must be very low and the heater must have a dedicated circuit (15 amps
minimum) with no GFCI outlets being used. If unsure what a GFCI outlet is, contact a certified electrician.
F&-#3#9+%#)0(%#'$&-#0-%#$%&'%(#&'#&#'*)%<#F&-#3#9+%#'$%#$%&'%(#&-1#&-0'$%(#&55=*&-G%#&'#'$%#+&)%#
'*)%<#
Yes. But make sure they are not plugged into the same circuit. Each heater (heaters are considered
appliances, and draw out high amperage) requires its own minimum 15 amp circuit (with no other items
plugged into that circuit or outlet). If unsure your circuit meets these requirements, verify with a certified
electrician. Risk of fire, damage to property, or injury may result if requirements are not met.

!C"
;$"#10%+#)"#$%&'%(E+#4&-#G0-'*-9%#'0#(9-#&4'%(#'$%#+%'#'%)5%(&'9(%#*+#(%&G$%1#0(#'$%#502%(#*+#'9(-%1#
044<#
This is normal. The heater’s fan will continue to run, even after the heater automatically cycles down. The
fan continues to run so that every last bit of heat is blown out of the heat chamber, while allowing the unit to
continue filtering your air. Once the internal box/components cool completely, the fan should then shut off on
its own. In this case, allow a few minutes after the heat cycles off (with power on). The fan will shut off faster
when the power is turned off.
;$"#10%+-E'#'$%#4&-#+5%%1#*-G(%&+%#2$%-#3#G$&-.%#'$%#+%''*-.#4(0)#P02#'0#Q*.$<#
This is normal. The heater’s fan’s speed is not affected by the High/Low settings. The fan is designed to
vent the heat at one soft, comfortable, and energy efficient speed. What is affected by the High setting is the
heat output. In essence, in the High mode, the heater produces “more” heat, rather than “faster” heat.
3#2&-'#'0#)&J%#+9(%#)"#2&((&-'"#*+#(%.*+'%(%1:#;$&'#10#3#+%-1#'0#)&J%#+9(%#*'#*+#(%.*+'%(%1<#
;$%(%#10#3#+%-1#*'<#
The heater comes with an automatic 1-year limited manufacturer’s warranty at the time of purchase. Your
receipt is considered your proof of purchase and registration. Keep it in a safe place. As long as it is legible,
a copy may be used for any future warranty claims (if requested). If you have access to e-mail, and would
like peace of mind, e-mail us to: 6$I*D%J"%*).K2*#$D1"J%LJ)MN+%DO+)1 In the body of the e-mail, include your
full name, address, phone number, model, serial number, and scanned copy of your legible receipt. You may
also register in the “registration” tab at: www.lifesmartproducts.com.
!"#$%&'%(#10%+#-0'#5%(40()#&+#2%==#&+#&-0'$%(#6(&-1#$%&'%(#'$&'#3#59(G$&+%1:#;$"#R0'<#
There are many brands of heaters on the market. Each brand is designed with different heat specifications,
designs, trademarks, fan speeds, colors, material types, displays, and electrical components. They are
manufactured this way for you, as the consumer to have choices, selection, and preferences. As long as the
unit functions as specifications indicate, comparison to other brands will ultimately depend on individual
consumer perception.
3#59(G$&+%1#)"#$%&'%(#+0#'$&'#*'#G09=1#G9'#)"#$%&'*-.#G0+'+A#69'#)"#%=%G'(*G#6*==#$&+#.0-%#95:#;$"<#
The compact LIFESMART heater can definitely save you on heating costs, when compared to the existing
central heating system in your home, and when used as supplemental heat. Your heater is designed to give
your main heat source a supplement “boost,” or allow for you to have extra heat (in the form of soft infrared
waves) in locations where you would otherwise be short. It is meant to cycle on and off as it provides the
central heat the boost it needs. If you intend on using it as a single heat source, especially in larger homes
(which you may), expect the heater to 1) take as much as 24 hours to heat the area, 2) stay on for longer
periods of time (without cycling off) due to heat loss, and 3) increased use time, and electric costs.

!!"
!"#$%&'%(E+#1*+5=&"#+$02+#)"#&)6*%-'#'%)5%(&'9(%#'0#6%#*-#'$%#M@E+A#2$%-#3#J-02#*'#*+#2&()%(#
'$&-#'$&':#;$"<#
The heater’s display is defaulted to read the temperature as Fahrenheit. If your heater is definitely heating,
but shows it is in the 20’s, you probably have the setting to read your temperature in Celsius, rather than
Fahrenheit. See Users Guide to change.
#
!"#$%&'%(#$&+#&#'%)5%(&'9(%#+%''*-.#*-1*G&'*-.#SFI:#3'#*+#+9550+%1#'0#6%#%44*G*%-'A#69'#*'#+%%)+#'0#
-0'#$%&'#&+#)9G$:#;$"<#
The ECO mode on your heater is a program that attempts to keep the temperature strictly at a “warm” 68° F.
This also helps with efficiency, as it is programmed to 1) Increase the wattage used to 1500W if the
temperature drops below 64.4°F 2) Gradually reduce the wattage used as it approaches 66.2° F and 3) Stop
heating when 68° F is achieved. This is considered an Economical function, since in the ECO setting, the
heater is almost never running on the full 1500 Watts. If this “warm” heat is not plentiful or is “On” constantly,
and you fear it will increase your electric bills, we recommend you set it to the High or Low setting and have
it cycle off when your set temperature is achieved. You may also set the timer to allow your heater to shut off
at the given hour increments you desire. See User’s Guide to set the timer.
#
!"#Q%&'%(E+#T02%(#G0(1#.%'+#2&():#!"#G0(1#*+#+$02*-.#+*.-+#04#$%&'#0(#)%='*-.#&'#'$%#09'=%':#3+#'$*+#-0()&=<#
A warm power cord is normal. All LIFESMART power cords are rated safe for up to 105° C/ 221° F by the
UL, CSA, or ETL. The exception is, if you detect heat, smoke, or signs of melting at the contact point of the
wall outlet, it may be due to loose or worn wall contacts (or arcing). Please stop using the heater
immediately, contact LIFESMART warranty support for a replacement power cord, and have a certified
electrician replace the wall outlet as soon as possible.#

!#"
HEATER OPERATION
Here is a small description of how our heaters work:
Operation Mechanism:
1) Air is brought into the heater through an easy to clean, washable filter at the rear of the
unit.
2) The highly efficient, one-speed, high volume fan pushes filtered air through the chamber,
across the heat elements.
3) During this exchange, heat is accumulated and transferred to the air in the chamber.
4) The newly transferred filtered, clean, and hot air is then circulated out the infrared
heater’s front vent.
5) The whole process produces variably hot air, compared to the air originally entering the
heater.
6) This method of heat generation creates an even, comfortable level of infrared heat from
floor to ceiling (as opposed to venting hot air blowing that will just rise to the ceiling and
dissipate)
There is no drying of the air with this method of heating and no harmful chemicals or pollutants
are released.

!$"
HEATER PLACEMENT
By using this infrared heater you can efficiently heat up to 1500 of unobstructed square feet.
This heater is NOT intended to replace your home’s furnace. Rather, it is designed to be a
supplement to it. It is not an instant heater, and on occasions (depending on various factors),
can take up to 24 hours for a room to reach the desired temperature. Your Infrared Heater is
equipped with a lifetime washable static filter system which removes airborne contaminates as
air circulates into the heating chamber.
To achieve maximum efficiency of your Infrared Heater, please follow these recommendations:
1. Place your Infrared Heater at least 3 feet from an “inside” wall (a wall that is away from the
cold, outside perimeter of your house) of the room in which it will be used. Face the heater’s
exhaust vent (the grill) toward the cooler “outside” walls of the room. This positioning will
allow the heat to be moved across the room toward the outside walls to provide more even
warmth throughout the room.
2. Make sure that windows and doors are not allowing a high rate of airflow into the room where
you will be placing your heater. High airflow will minimize the effectiveness of your Infrared
heater, as it would any conventional type heater.
3. For best results, always try to maintain a minimum of 40% relative humidity in the
environment to be heated.
4. It is recommended that the Infrared heater be used in rooms that are insulated according to
code. You can use your heater in a room whether insulated or not, but a non-insulated room
will cause greater and faster heat loss which is counterproductive, and will keep the heater in
the “on” cycle longer. This may increase your electricity costs.
5. Keep the area around the heater clear of clutter and obstacles so that there is free airflow to
and from the heater.
6. Make sure to keep your heater out of the main traffic area of the room in which it is located; it
should be a welcome addition to the room rather than an obstacle to be stepped over or
stepped around.
7. The heater will pull a good amount of power (between 10-14 amps on average) from the wall
outlet and from the circuit (the circuit is considered all the outlets and lighting that is
controlled by a single house breaker). The heater needs to be connected to an individual
circuit with nothing else connected to that circuit. Doing so will exceed the maximum
amperage allowed for that breaker. Excessive heat, hot power cords, damage to outlets, and
risk of fire will be the result, if not adhered to, and will void your warranty (releasing
LIFESMART from any liability).

!&"
USER’S GUIDE
Plug your Infrared Heater power cord into a 120V, 15amp (or higher) three-prong receptacle. "
To Turn the Heater On:
1. Turn the Master toggle switch in the back of the heater to the “On/Lit” position.
2. Press the “Power” button on the front control panel or “ON/OFF” button on the remote
control.
Heater Default Temperature:
The heater’s default temperature every time it is powered “on” is 72°F.
•Note that the heater will not activate its heat elements or fan, if the starting ambient
temperature (temperature in the room) is above 72°F.
•If this is the case, the set desired temperature must be first be adjusted above the
ambient temperature.
Ambient Temperature (room temperature):To view the ambient room temperature, press
the “Temp up” and “Temp down”buttons at the same time for appx 3 seconds. The room
temperature will display for 5 seconds then return to the desired set temperature.
Set Desired Temperature (Goal Temperature):Press the “Temp up” or “Temp down”
button on the control panel or on the remote control to select the Set Desired Temperature. The
heating process will begin.
•When the heater detects that the ambient room temperature matches the set desired
temperature, the heating will stop automatically.
•The fan will continue to run for a few extra minutes so that the unit’s chamber can cool,
then the fan will also shut off. When the ambient temperature drops below the set desired
temperature once again, the heater will restart the heating cycle.
To Set Heat Mode:Press the “High/Low/Eco” button on the control panel or “H/L/E” on the
remote control to switch between the High, Low, and Eco modes. The corresponding High, Low
or Eco light will switch on. Note that in all modes, the fan speed will remain the same.

!'"
Heating Process:
In the High Mode, all heating elements will engage for full 1500 Watt heating capacity.
In the Low mode, corresponding heating elements will engage to heat at 1000 Watts, to save
energy. This mode can be used when some heat is needed, but not at full capacity.
In the Eco mode, the heater’s Set Desired Temperature will automatically default to 68°F. The
heater will determine heating element usage based on the ambient room temperature. If the
ambient room temp is below 64°F, all heating elements engage. As the ambient temperature
approaches 68°F, the number of heating elements used decreases. The heating elements will
disengage when 68°F is achieved.
The On/Off Timer: For your convenience, our heater also comes with a built in timer. This is a
function that allows for you to set the heater to Power on (to default set temp) or Power off at
desired hourly intervals.
To Set “On” Timer:With the master switch in the back of the unit “on” position, press the
“Time” button on the front control panel or remote control. The number 0 will appear on the
display. “Zero” indicates there is no specified time frame for the heater to turn on. This can be
increased in hourly increments by pressing the “time” button. The number chosen (1, 2, 3. . .12)
determines how many hours before the heater automatically turns on. After the number is set,
the display will show only the hours or minutes remaining until it automatically turns on.
To Set “Off” Timer:While the heater is heat cycling, press the “timer” button. The number 0
will appear on the display. “Zero” indicates there is no specified time frame for the heater to turn
off (it will cycle on and off based on the set desired temperature). This can be increased in
hourly increments by pressing the “time” button. The number chosen (1, 2, 3. . .12) determines
how many hours before the heater automatically turns off. The display will automatically go back
to the displaying the set desired temperature after 5 seconds of button inactivity.
Celsius and Fahrenheit:The heater displays temperature in Fahrenheit as the default, but has
the capability to display it in Celsius as well.
To change between °Celsius and °Fahrenheit: Press “C°/F°”

!U"
FILTER MAINTENANCE
Your Infrared Heater is equipped with an easy to clean, washable static filter. Regular cleaning
and maintenance of your filter will ensure a lifetime of trouble-free use.
1. Turn off the heater. Locate the filter at the rear of the heater and lift out (some filters may be
held on by brackets. Others may be magnetic. Others may require loosening up some screws).
2. Rinse the filter by spraying warm tap water through the filter. Make sure the water is sprayed
into the side that faces the inside of the heater, and comes out of the side that faces away from
the heater. Continue spraying until the filter is clear of dust and debris.
3. If the filter is extremely dirty or clogged with grease, you can soak the filter in a mild solution of
dish soap and water, then brush (the side that faces away from the heater) with a soft brush and
repeat the rinsing process.
4. Shake filter to remove excess water and lay on clean cloth or paper towels to dry. Do not use
heat source to dry filter.
5. Reinstall the filter on to the heater after it is completely dry. Do not use this filter for any other
purpose.
NOTE: Never operate the heater without a filter in place. Without the filter, dust can
accumulate on the heater’s components and cause damage.

!V"
>*1*%$M'4".N#"+%NJ$J'@"JJ".%&'
P':$"J'>*1*%$M'@"JJ".%&Q">39/!4867'4-//-;.+".)*+"),-.,/"-@-*;+."3,8,<.+"*;"?-.,/*->+"-;3"46/Y?-;+)*2").'
#N.+%*)."2'L"J%D?"86/"-"2,/*63"68"6;,"9,-/"8/6?".),"6/*@*;->"3-.,"68"21/<)-+,%":)NJ'D"2$D'J$+$*L%'D-)R*.I'%-$'M"%$')#'
LNJ+-"D$')#'%-$'LJ)MN+%'*D'&)NJ'LJ))#')#'LNJ+-"D$O'Z,,2"*."*;"-"+-8,"2>-<,"86/"81.1/,"/,8,/,;<,%"
"
4".N#"+%NJ$J'@"JJ".%&''
"""D>>">39/!4867'2/631<.+"-/,"?-;18-<.1/,3"4*.)".),")*@),+."01->*.9"?-.,/*->+"-;3"-/,"4-//-;.,3".6"B,"8/,,"8/6?"
3,8,<.+"*;"?-.,/*->"-;3"46/Y?-;+)*2"-.".),".*?,"68"21/<)-+,%"()*+">*?*.,3"4-//-;.9"-22>*,+".6"2/631<.+"
?-;18-<.1/,3"6/"3*+./*B1.,3"B9".),"RSJIL[DP("B/-;3";-?,="-/,"3,>*7,/,3"*;".),"E6;.*;,;.->"O;*.,3"L.-.,+="E-;-3-="
-;3",F.,;3+".6".),"6/*@*;->"21/<)-+,/="6/"@*8."/,<*2*,;.%"()*+"4-//-;.9"B,<6?,+"7->*3"-.".),".*?,"68"21/<)-+,"-;3"
.,/?*;-.,+",*.),/"B9".),"+2,<*8*,3".*?,"8/-?,">*+.,3"-B67,"-;3\6/"64;,/"./-;+8,/"]1;>,++"6.),/4*+,"-1.)6/*^,3"B9"
RSJIL[DP(="-+".),"?-;18-<.1/,/_%"D;9",F.,;3,3"4-//-;.*,+"]4-//-;.*,+".)-."<67,/"-B67,"-;3"B,96;3".)*+"
?-;18-<.1/,/"4-//-;.9_".)-."-/,"+6>3".)/61@)"-"/,.-*>,/"6/".)*/3"2-/.9="-/,";6."3*/,<.>9"<6//,>-.,3"4*.)".)*+"
RSJIL[DP(">*?*.,3"4-//-;.9="-;3"?-9"B,"/,3*/,<.,3".6"+-*3"/,.-*>,/"6/".)*/3"2-/.9"86/"<67,/-@,%"D;9"P,81;3+"6/"
?6;,.-/9"<6?2,;+-.*6;+"?1+."B,"<>-*?,3".)/61@)".),"2>-<,"68"21/<)-+,"]/,.-*>,/_="-;3";6.".)/61@)">39/!4867'-+"
.),"?-;18-<.1/,/%'"
""
/S%$.%')#'@"JJ".%&'
()*+"4-//-;.9",F.,;3+".)/61@)".),"?-;18-<.1/,/"68".),"2/631<.="-;3"<67,/+"81;<.*6;->"2-/.+"6;>9%"E6+?,.*<+"-/,"
;6."<67,/,3="1;>,++"1;,01*76<->>9"3,.,/?*;,3"*."*+"-"?-;18-<.1/,/\46/Y?-;+)*2"3,8,<.%"H6.,".)-."+1/8-<,"</-<Y+"
-/,";6."<6;+*3,/,3"3,8,<.+"*;"?-.,/*->"6/"46/Y?-;+)*2="-+".),9"-/,";6/?->"<)-/-<.,/*+.*<+"68"->>"4663%'O;>,++"
RSJIL[DP("4-+".),"3*/,<."+)*22,/="+)*22*;@"3-?-@,"+)61>3"B,"-33/,++,3"4*.)".),"+)*22*;@"<6?2-;9="/,.-*>,/="6/"
2>-<,"68"21/<)-+,="2/*6/".6"?-Y*;@"-"<>-*?".6"RSJIL[DP(="-+".),"?-;18-<.1/,/%"'
"""(),"?-;18-<.1/,/`+"+6>,"6B>*@-.*6;"1;3,/".)*+"4-//-;.9"+)->>"B,">*?*.,3".6"81/;*+)*;@".),"6/*@*;->"21/<)-+,/"
/,2>-<,?,;."2-/.+"86/"1;*.+"3,,?,3"!"#$%!$&'""B9".),">39/!4867'4-//-;.9"3,2-/.?,;.%"(),"21/<)-+,/"?-9"->+6"62."
.6"+)*2".),"2/631<.".6"RSJIL[DP(".6")-7,"*."/,2-*/,3="4*.)"2/*6/"4/*..,;"-1.)6/*^-.*6;"8/6?"-">39/!4867"4-//-;.9"
3,2-/.?,;.%"(),"21/<)-+,/"4*>>"B,"/,+26;+*B>,".6"2/,2-9"-;9"+)*22*;@"<)-/@,+"]B6.)"4-9+_=",F26/.".-F,+="<1+.6?"
31.*,+"-;3".-F,+="6/"-;9"6.),/"<)-/@,+"-++6<*-.,3"4*.)".),"./-;+26/.-.*6;"68".),"1;*.%"S;"-33*.*6;=".),"21/<)-+,/"*+"
/,+26;+*B>,"86/"*;+1/*;@"-;9"2-/.+"+)*22,3"6/"/,.1/;,3="*8"3,+*/,3%"J6/"2/631<.+".),"4-//-;.9"3,2-/.?,;."3,,?+"()*
!"#$%!$&'"+,-!,.%/0-)1%)(".+">39/!4867'/,+,/7,+".),"/*@).".6"*++1,"-"/,81/B*+),3"2/631<.="6/"2/631<."+*?*>-/"*;"
81;<.*6;->*.9"-+"-"/,2>-<,?,;."86/".),"3,8,<.*7,"1;*.="*4#&K&*=&6=%:#D;"->.,/;-.*7,".6"-"/,2>-<,?,;.+"]>39/!4867'
=*D+J$%*)._"4*>>"B,"<6;+*3,/,3"86/"2/631<.+"3*+<6;.*;1,3"]6/";6."-7-*>-B>,_"-.".),".*?,"68".),"<>-*?"?-9"B,"
;,@6.*-.,3"4*.)"-"8-*/"-;3"<6?2-/-B>,"->.,/;-.*7,%""D>>",F<)-;@,3"2-/.+"-;3"2/631<.+"/,2>-<,3"1;3,/".)*+"4-//-;.9"
4*>>"B,<6?,".),"2/62,/.9"68'>39/!4867O'>39/!4867'/,+,/7,+".),"/*@).".6"<)-;@,"?-;18-<.1/,/+"68"/,2>-<,?,;."
2-/.+"6/"2/631<.+"86/"1+,="*;"6/3,/".6"<67,/"-;9",F*+.*;@"4-//-;.9%"D;9"2-/.+"3,.,/?*;,3"3,8,<.*7,"?-9"-+Y,3".6"B,"
/,.1/;,3".6">39/!4867')J"*.+"/,2/,+,;.-.*7,+".6"7->*3-.,"-"<>-*?%"H6;5A-//-;.9"/,2>-<,?,;."2-/.+"4*>>"B,"4-//-;.,3"
$C"3-9+"8/6?".),".*?,".),"21/<)-+,/"/,<,*7,+".),?%""
"""(),"21/<)-+,/"?1+."2/,+,;.">39/!4867'4*.)"2/668"68"21/<)-+,"36<1?,;.+"]*;<>13*;@".),"3-.,"68"21/<)-+,_"*8"
/,01,+.,3%"D;9",7*3,;<,"68"->.,/-.*6;=",/-+*;@="6/"86/@,/9"68"2/668"68"21/<)-+,"36<1?,;.+"4*>>"B,"a1+."<-1+,".6"T53="
.)*+">*?*.,3"4-//-;.9%"N/631<.+="*;"4)*<)".),"+,/*->";1?B,/")-+"B,,;"3,8-<,3"6/"/,?67,3="-/,";6.",>*@*B>,"86/"
4-//-;.9"<67,/-@,%""
'
'

!W"
@"JJ".%&'>*1*%"%*).D''
()*+"4-//-;.9"36,+";6."-22>9"*8".),"1;*.")-+"B,,;"+1Ba,<.".6";,@>*@,;<,="8-B/*<-.*6;="?*+1+,="-B1+,="6/"/,2-*/+"]1;>,++"
-1.)6/*^,3"7,/B->>9="6/"*;"4/*.*;@="B9"-;"D1.)6/*^,3"RSJIL[DP("P,2/,+,;.-.*7,_"->.,/-.*6;"B9";6;">39/!4867'"
-1.)6/*^,3"2,/+6;;,>="*;-22/62/*-.,"*;+.->>-.*6;+="6/"-;9"<-+,"B,96;3".),"<6;./6>"68">39/!4867'O"IF-?2>,+"68"
4-//-;.9"*;7->*3-.*6;"?-9"->+6"*;<>13,="B1."-/,";6.">*?*.,3".6b""
•F$"%$J',2NII$M'*.%)'"'>))D$')J'="1"I$M'
5N%2$%'
•F$"%$J'L2"+$M').'.).0"LLJ)U$M'DNJ#"+$D')J'
.).0"LLJ)U$M'"J$"D'VDN+-'"D'W"%-J))1D?'
2"N.MJ&'"J$"DX''''
•/2$+%J*+"2'J$YN*J$1$.%'M$#*+*$.+*$D'VPZ0[\'
"1L'M$M*+"%$M')N%2$%XO"[ND%'W$'L2NII$M'*.%)'
"'P[\T?'PZ'"1L'V)J'1)J$X'+*J+N*%')#'*%D')R.O'
()%-*.I'$2D$'+".'W$'L2NII$M'*.%)'%-$'D"1$'
+*J+N*%O'
•;D$').'/S%$.D*).'<)JMD]7*1$JD]!NJI$'
,J)%$+%)JD]A9<3'
•5N%M))J],"%*)]E"2+).&'"LL2*+"%*).D''
•,$%]<).DN1$J'"++*M$.%D'
•,NJ+-"D$D'#J)1'M$"2$JD'.)%'"N%-)J*^$M'W&'
>39/!4867''V8N%-)J*^"%*).'*.'RJ*%*.IX'DN+-'"D'
8N+%*).D?',J$U*)ND2&'5R.$M?'A"J"I$'!"2$D?'
7J"U$2*.I'!"2$DL$JD).D''
Disclaimers
>39/!4867'+)->>";6."B,">*-B>,"86/"-;9">6++"31,".6"1+,"]6/"?*+1+,_"68".),"),-.,/"6/"6.),/'>39/!4867'LJ)MN+%D"6/"6.),/"
*;<*3,;.->"6/"<6;+,01,;.*->"<6+.+=",F2,;+,"6/"3-?-@,+"4*.)61."*//,81.-B>,"861;3-.*6;+%"O;3,/";6"<*/<1?+.-;<,+"+)->>"
>39/!4867'6/"-;9"68"*.+"/,2/,+,;.-.*7,+"B,"),>3">*-B>,"86/"*;a1/9".6"-;9"2,/+6;"6/"3-?-@,".6"-;9"2/62,/.9=")64,7,/"
-/*+*;@%"D;9"*?2>*,3"4-//-;.9"+)->>")-7,"31/-.*6;",01->"68".),"-22>*<-B>,"4-//-;.9"+.-.,3"-B67,%"L2,<*8*<-.*6;+"-/,"
+1Ba,<.".6"<)-;@,"4*.)61.";6.*<,"6/"6B>*@-.*6;%

" "
!X"
Legal Remedies
This limited warranty gives the original purchaser specific legal rights. Other rights may vary from state to state.
" " RL5!CCCc5UA"PId!"NPSH(IG"SH"EKSHD"