Life Smart LS-6BPIQH-X Quick start guide

1
O
OW WN NE ER RS S I IN NS ST TA AL LL LA AT TI IO ON N A AN ND D O OP PE ER RA AT TI IN NG G M MA AN NU UA AL L
LIFESMART INFRARED HEATER
Model: LS-6BPIQH-X
Safety Notice
Please read this entire Installation and Operating Manual BEFORE installing and using
your new Infrared Heater. Failure to fully understand and follow instructions may result in
property damage, bodily injury, or even death.
If the Infrared Heater in not used properly, a house fire may result. For everyone’s safety,
FOLLOW all Installation and Operating Directions.
Save These Instructions

2
TABLE OF CONTENTS
Topic Page(s)
Customer Service & Support 3
Introduction & Specifications 4
Important Safety Information 5-7
Frequently Asked Questions 8-11
Heater Operation 12
Heater Placement 13
Users Guide 14-15
Air Filter Maintenance 16
Warranty 17-19
*Contents in the box:
1. Infrared heater (1unit)
2. Instruction manual (1pcs)
3. Remote Control (2 AAA batteries not included) (1pcs)

3
Customer Service and Support
To Obtain Warranty Support or Advice, Please Complete These Easy Steps:
Contact LIFESMART PRODUCTS Technical Support
Phone:[phone] or 1-214-614-2509
E-mail:[e-mail]
Visit us: www.lifesmartproducts.com
You will need to provide the unit's model number, serial number (located on the
heater’s front panel, rear panel, or on the box), date of purchase, retailer of
purchase, a daytime phone number, and possibly a copy of your receipt.
Be Patient, Clear, and Concise.
Describe the issue and symptoms you have for, and about the product. A certified
LIFESMART Technical Support agent will give you an evaluation of your issue and your
resolution options. If the answer is not available at that time, you will be referred to the
appropriate channels, or given a call/e-mail back within 72 hours with an answer or
resolution.
If after speaking with LIFESMART Technical Support, it is determined by one of our
agents that your unit may need to be sent in to us to be evaluated/repaired, our
representative will provide you with a reference number and provide you with details
on how to send in your unit for repair.

4
INTRODUCTION
Thank you for choosing one of the best Infrared distribution heaters available on the market
today. Our Infrared Heater is a very safe and effective room heater. It produces safe, clean and
economical heat by utilizing quartz infrared heating elements. The heating process of the
Infrared Heater is similar to the way the sun warms the earth. The infrared elements warm the
heat chamber and the whisper quiet fan distributes the accumulated warmth. This process is
unique among heaters in that it minimizes wasteful heat collection at the ceiling height of rooms
and targets it toward the living space instead. Thank you for being our customer, and enjoy your
heater!
Our Infrared Heaters have been tested and listed for installation in residential and mobile homes
by ETL:
3189533
Conforms to UL STD. UL1278
Certified to CSA STD. C22.2 NO.46
SPECIFICATIONS:
Electrical:
Voltage: 120V~60Hz
Power consumption: Low 1000 Watts/High 1500 Watts
Thermostat range: 50-90 Fahrenheit
Coverage:
Up to 1500 square feet of unobstructed area
Dimensions:
16.5” x 13.2” x 16.9”, 18.7 lbs
Safety Features:
Advanced Safety Overheat Shut Off
Tip Over Shut Off
Features:
Remote Control
High/Low/Eco Heat Settings
Air filtration system
Lifetime Washable Filter
On/Off Timer
Injection Molded Plastic Cabinet

5
IMPORTANT SAFETY INSTRUCTIONS
READ AND UNDERSTAND ALL INSTRUCTIONS, SAFETY WARNINGS,
AND FAQ’s BEFORE USING THE HEATER
WARNING!
! POTENTIAL FOR ELECTRICAL HAZARD IF NOT ADHERED TO!
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electric shock, and injury to persons, including the following:
1. This heater must be plugged into a 120V, 15 amp (or more) circuit of its own. Nothing
else can be plugged into the same circuit. If unsure if your home meets this
specification, consult a certified electrician prior to use. Risk of fire, overheat,
malfunction, property damage, injury, or even death may result if not adhered
to!
2. Connect to a properly grounded, 3-prong outlet only. Do not connect the heater to
extension cords, surge protectors, timers, direct breakers, or an outlet with other
appliances connected to the same outlet. Risk of fire, overheat, malfunction,
property damage, injury, or even death may result if not adhered to!
3. This heater is hot when in use. To avoid burns, do not let bare skin touch hot
surfaces. Use handles (certain models) or wheels to move this heater.
4. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and
curtains from the front of the heater and keep them away from the sides and rear of
the heater.
5. Extreme caution is necessary when any heater is used by or near children, invalids,
pets, or when the heater is left operating unattended.
6. Always unplug the heater when not in use.
7. Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped, or damaged in any manner. Contact the
manufacturer for resolution options.
8. Do not use outdoors. Exposure to outdoor elements such as rain, snow, sun, wind or
extreme temperatures may cause the heater to become a safety hazard.
9. This heater is not intended for use in bathrooms, laundry areas and similar indoor
locations, nor any locations that use GFCI outlets.

6
10.Never place heater where it may fall into a bathtub or other water receptacles.
11.Do not run cord under carpet. Do not cover cord with throw rugs, runners, or similar
coverings. Arrange cord away from traffic area and where it will not be tripped over.
12.The heater must be plugged into a wall outlet that is a DEDICATED CIRCUIT, with a
minimum 15 amp rating on that individual circuit.
13.To disconnect the heater: FIRST, turn the power button to the “off”position, then
remove plug from the wall outlet.
14.Do not allow foreign objects to enter or block any ventilation or exhaust opening as
this may cause an electric shock or fire, or damage the heater.
15.Allow at least 3 feet of unobstructed space to the front and rear of the heater to allow
for maximum heat, air, and ventilation flow.
16.A heater has hot and arcing or sparking parts inside. Do not use it in areas where
gasoline, paint, or flammable liquids are used or stored, nor use flammable solvents to
clean the heater. Also, make sure to keep heater dry at all times.
17.Use this heater only as described in this manual. Any other use not recommended by
the manufacturer may cause fire, electric shock, or injury to persons.
18.Do not use abrasive solvents to clean the heater as it may cause damage to the finish
or casing.
PLEASE REVIEW FREQUENTLY ASKED QUESTIONS ON THE NEXT
FEW PAGES PRIOR TO USING YOUR HEATER.

7
FREQUENTLY ASKED QUESTIONS (FAQ’S)
My heater emits a “strange” odor when I first open the box/when I turn the heater on for the first
time. Why is this happening?
This is normal. This heater is treated with a special heat safe/resistant coating. This odor will sometimes
be present when the box is opened, and may be compared to a heaters version of “new car smell.” Also,
similar to all hearth appliances (woodstoves, etc.), the coating, exposed to heat, will produce this particular
odor during the first few hours of operation. This will dissipate after the break-in period. If you are sensitive
to odors, you may want to pre-burn the unit in a garage with the door open until the initial odor
dissipates.
If my heater runs on approximately 1500 Watts, how many BTU’s is that? Is that a lot of heat?
At 1500 Watts, your heater will use approximately 5100 BTUs. 5100 BTUs, compared to your home furnace,
is a very small amount of heat (this heater is intended to be used as supplemental heat in areas most
needed). It may take several minutes, to several hours to heat your area, depending on various factors (see
Heater Placement).
Can my heater really operate on less money per day? What are my operating costs?
Yes. If the heater is used as it is intended (as supplement/assist heat), it should cycle on and off, allowing for
it to heat a total of approximately 8 out of the 24 hours of the day. Using the national average of
approximately 10¢ per kWh (look at your bill for exact cost per kWh--will vary per state), your average
heating cost (add a few cents just for having it plugged in) should be less per day compared to your main
furnace. The costs will increase if it is used as the single source of heat, or if heat somehow escapes the
room being heated, since the “on” cycle will run longer.
The Formula: To determine the cost of this or ANY 1500 watt appliance, multiply 1.5 X your cost per
Kilowatt Hour to determine approximately how much it costs you to run the heater. You can find the cost per
KWH prices for your state at: http://www.eia.doe.gov/fuelelectric.html
Can the heating elements be replaced?
If after speaking to a Lifesmart Technical Support Agent, it is determined that heating elements have failed.
Heating elements may be replaced by obtaining them from the Manufacturer. All parts may be purchased
through LIFESMART PRODUCTS if your product is out of warranty. Note: If you feel that the elements are
definitely faulty right out of the box, contact the LIFESMART PRODUCTS Technical Support department first
(for troubleshooting and verification).They can then direct you on to the next step.

8
Once I plug the unit in and turn it on, how long will it take to heat my room?
The heating process in the heater begins immediately upon powering on, and setting the desired
temperature above the ambient temperature. A noticeable change in the l room’s ambient temperature will
vary. Remember that with any type of heating process, there are many variables: Location of heater (in the
home), floor plan and size of the room, how well the room is insulated, how many doors/windows, how much
bare concrete (acts as a heat sink with any type of heating), the opening and closing of an exterior door,
long hallways, high ceilings, etc. Customers with smaller rooms experience quick heat changes. Rooms with
larger and open floor plans can expect up to 24 hours to completely heat up.
I don’t have a grounded outlet; can I use adapters, a 2-prong power strip, or remove the ground
prong from the cord?
Definitely NOT! If you don’t have a grounded outlet, contact a certified electrician for advice. Removing or
altering any part of the heater’s original design or intent (including the power cord) will not only void the
warranty, but will make you liable for any unexpected or hazardous results.
Why doesn’t the temperature on my heater match the temperature display on my wall, or external thermostat?
This is completely normal. The temperature display on your heater may vary from the temperature display
on another thermostat (like the one mounted to your wall or a purchased external thermostat). This is
because the temperature sensor on the heater reads the temperature directly around the heater. With the
heater near the cold floor (and heat rising), any readings on elevated or external thermostats will differ in
readings on the heater. The best way to operate your heater is just to set the unit on “High” and dial up to a
temperature that feels comfortable to you. Then, leave it at that temperature, regardless of the mismatch.
The heater will cycle off when the set temperature is met or exceeded slightly.
My home is not insulated very well. Can I use the heater if I have vaulted or cathedral ceilings? I live in a structure
that is larger than 1000 square feet. Will this heater help me? Can I use the heater to heat multiple rooms at the
same time? Will I be able to use the heater in a basement or garage?
The answer to these is the same. Yes. You will be able to use it, but keep in mind that rooms/structures with
open floor plans, minimal insulation, adjacent rooms, or high ceilings will not retain the heat as efficiently,
and noticeable heat changes will come slowly. Also, the heater will stay on for longer periods of time (since it
takes so long to cycle off), and may increase your electric costs. Note that if you do use it in a garage or
basement, the moisture levels must be very low and the heater must have a dedicated circuit (15 amps
minimum) with no GFCI outlets being used. If unsure what a GFCI outlet is, contact a certified electrician.
Can I use more than one heater at a time? Can I use the heater and another appliance at the same
time?
Yes. But make sure they are not plugged into the same circuit. Each heater (heaters are considered
appliances, and draw out high amperage) requires its own minimum 15 amp circuit (with no other items

9
plugged into that circuit or outlet). If unsure your circuit meets these requirements, verify with a certified
electrician. Risk of fire, damage to property, or injury may result if requirements are not met.
Why does my heater’s fan continue to run after the set temperature is reached or the power is turned
off?
This is normal. The heater’s fan will continue to run, even after the heater automatically cycles down. The
fan continues to run so that every last bit of heat is blown out of the heat chamber, while allowing the unit to
continue filtering your air. Once the internal box/components cool completely, the fan should then shut off on
its own. In this case, allow a few minutes after the heat cycles off (with power on). The fan will shut off faster
when the power is turned off.
Why doesn’t the fan speed increase when I change the setting from Low to High?
This is normal. The heater’s fan’s speed is not affected by the High/Low settings. The fan is designed to
vent the heat at one soft, comfortable, and energy efficient speed. What is affected by the High setting is the
heat output. In essence, in the High mode, the heater produces “more” heat, rather than “faster” heat.
I want to make sure my warranty is registered. What do I send to make sure it is registered?
Where do I send it?
The heater comes with an automatic 1 year limited manufacturer’s warranty at the time of purchase. Your
receipt is considered your proof of purchase and registration. Keep it in a safe place. As long as it is legible,
a copy may be used for any future warranty claims (if requested). If you have access to e-mail, and would
like peace of mind, e-mail us to: [e-mail] In the body of the e-mail, include your
full name, address, phone number, model, serial number, and scanned copy of your legible receipt. You may
also register in the “registration” tab at: www.lifesmartproducts.com.
My heater does not perform as well as another brand heater that I purchased. Why Not?
There are many brands of heaters on the market. Each brand is designed with different heat specifications,
designs, trademarks, fan speeds, colors, material types, displays, and electrical components. They are
manufactured this way for you, as the consumer to have choices, selection, and preferences. As long as the
unit functions as specifications indicate, comparison to other brands will ultimately depend on individual
consumer perception.
I purchased my heater so that it could cut my heating costs, but my electric bill has gone up. Why?
The compact LIFESMART heater can definitely save you on heating costs, when compared to the existing
central heating system in your home, and when used as supplemental heat. Your heater is designed to give
your main heat source a supplement “boost,” or allow for you to have extra heat (in the form of soft infrared
waves) in locations where you would otherwise be short. It is meant to cycle on and off as it provides the

10
central heat the boost it needs. If you intend on using it as a single heat source, especially in larger homes
(which you may), expect the heater to 1) take as much as 24 hours to heat the area, 2) stay on for longer
periods of time (without cycling off) due to heat loss, and 3) increased use time, and electric costs.
My heater’s display shows my ambient temperature to be in the 20’s, when I know it is warmer
than that. Why?
The heater’s display is defaulted to read the temperature as Fahrenheit. If your heater is definitely heating,
but shows it is in the 20’s, you probably have the setting to read your temperature in Celsius, rather than
Fahrenheit. See Users Guide to change.
My heater has a temperature setting indicating ECO. It is supposed to be efficient, but it seems to
not heat as much. Why?
The ECO mode on your heater is a program that attempts to keep the temperature strictly at a “warm” 68° F.
This also helps with efficiency, as it is programmed to 1) Increase the wattage used to 1500W if the
temperature drops below 64.4°F 2) Gradually reduce the wattage used as it approaches 66.2° F and 3) Stop
heating when 68° F is achieved. This is considered an Economical function, since in the ECO setting, the
heater is almost never running on the full 1500 Watts. If this “warm” heat is not plentiful or is “On” constantly,
and you fear it will increase your electric bills, we recommend you set it to the High or Low setting and have
it cycle off when your set temperature is achieved. You may also set the timer to allow your heater to shut off
at the given hour increments you desire. See User’s Guide to set the timer.
My Heater’s Power cord gets warm. My cord is showing signs of heat or melting at the outlet. Is
this normal?
A warm power cord is normal. All LIFESMART power cords are rated safe for up to 105° C/ 221° F by the
UL, CSA, or ETL. The exception is, if you detect heat, smoke, or signs of melting at the contact point of the
wall outlet, it may be due to loose or worn wall contacts (or arcing). Please stop using the heater
immediately, contact LIFESMART warranty support for a replacement power cord, and have a certified
electrician replace the wall outlet as soon as possible.