Life Smart LS-PH08H Operator's manual











READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a
safe place for future reference. Do not allow anyone who has not read these instructions
assemble, plug in, turn on, or operate the heater.
E
El le ec ct tr ri ic c W Wa al ll l P Pa an ne el l H He ea at te er r 
Model:LS‐PH08H


PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of
fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using this heater.
2. Extreme caution: This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety. Children
should be supervised to ensure that they do not play with the appliance.
3. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible
materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front
of the heater and keep them away from the sides and rear.
4. Always unplug heater when not in use.
5. Do not operate the heater with a damaged cord or plug or after the heater malfunctions, has been dropped or
damaged in any manner. Return it to authorized service facility for examination, electrical or mechanical
adjustment, or repair.
6. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never place the
heater where it may fall into bathtub or other water receptacles.
7. Do not run cord under material. Do not cover cord with throw rugs, runners, or similar coverings.
8. To prevent a possible fire, do not block the space between the heater and the wall which is for air intake or
exhaust in any manner.
9. A heater has hot and arcing or sparking parts inside. Do not use it in the areas where gasoline, paint, or
flammable liquids are used or stored.
10. Use this heater only as described in this manual. Any other use not recommended by the manufacturer
may cause fire, electric shock, or injury to persons.
11. If the supply cord is damaged, it must be replaced by the manufacturer, a service agent, or qualified
persons in order to avoid a hazard.
12. The heater must not be mounted over or directly above or below a power outlet.
13. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire.
14. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances
working. Do not install the heater under the wall socket.
15. It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle)
and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or
worn outlet.
16. The output of this heater may vary and its temperature may become intense enough to burn exposed skin.
Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to react to
avoid burns.
17. WARNING: In order to avoid overheating, do not cover the heater.
18.SAVE THESE INSTRUCTIONS

Included In the Box
Items Required For Mounting
Gettin
g
Started
1. Unpack your heater and any packing materials
2. If all items are enclosed, thoroughly Inspect the heater for any shipping damage (cracks, dents, broken
power buttons, etc.) prior to doing anything else. If it was damaged in transit, contact your place of
purchase immediately.
1. Main Components:
·(Qty 1) Panel Heater
·(Qty 1) Instruction Manual
2. Mounting Hardware Pack Consisting of :
·(Qty 4) Plastic Mounting Posts w/ Built-In Wall Achor
·(Qty 1) Drill Bit
·(Qty 4) Long Mounting Screws
·(Qty 4) Plastic Screw Head Caps
2 People (to help hold it) · Mounting Hardware Pack · Power Drill · Medium Phillips Screwdriver · Small
Level · Pencil for marking the wall (if you think you may have to erase) or a Fine Tip Marker · Medium
Strength Glue (recommended but not essential)

Precautions Prior to Mounting
Mounting Instructions (Reference Fig 1-8 Next Page)
・2 People will be required to complete the mounting process.
・Keep all packaging and packaging materials until you have inspected the heater and all the contents of
the mounting hardware.
・The mounting hardware pack contains small items that should be kept away from young children.
・Do not plug in or power up the heater until it is secure to the wall and the instructions are read fully.
・Please choose a mounting location wisely, prior to starting. A power outlet must be within the
cord’s reach, but the heater must not be mounted over or within 12 inches above or below the
outlet.
・Please observe the recommended heights and dimensions for mounting the heater.
・This appliance is designed to be mounted to a wall at a minimum height of 8 inches from the floor.
・Take necessary precautions to avoid cutting or damaging any cables or power cords.
・While drilling holes for the mounting posts, be cautious of electrical lines, metals, or items beyond the
walls.
・Be sure that the wall you choose to mount on is solid, and will support the heater’s weight of
approximately 13 lbs.
・Make sure that the heater is safely out of the way while you are installing mounting hardware, as it
may become a tripping hazard if left in the open.
・Please be cautious if you are set on mounting the heater low to the floor, as it may become a
safety hazard to children and pets!
**Note: If you do not have a second person to assist, you may use the dimensions on Fig. 7 as a guide to
mounting without awkward handling of the heater.
1. Choose your mounting location based on the criteria in “Precautions Prior to Mounting.”
2. Make sure when choosing your mounting location, that the distance between the bottom of the heater
and the floor will be no less than 8 inches when the heater is installed
3. Once the mounting location is carefully picked out, and with assistance of a second person, lift the
heater, (with the flat side up against the wall) and straighten it using the small level.
4. Mark the positions of the four holes to be drilled on the wall with the pencil or marker (Ref. Fig 1).
5. At this point, lower the heater and place it where it will not be a tripping hazard.
6. Using the power drill, and the bit included in your mounting hardware kit, drill the marked holes on
the wall (Ref. Fig 2).
7. Insert the 4 plastic mounting posts into the holes. You should be able to press them in. If too difficult
to press, you may be able to lightly tap them in, using the screwdriver handle. (Ref. Fig 3)
8. Line up and slide the heater onto the 4 mounting posts the four holes in the heater (switch side towards
the wall). (Ref. Fig 4)
9. Once the heater is resting on the mounting posts, insert and tighten the screws onto the posts. (The
screwdriver is recommended to avoid stripping the posts or screw heads) (Ref. Fig 5)
10. Install the plastic end caps onto the heads of the screws. It is recommended to use a bit of medium
strength glue to hold each cap in place. (Extra strength glue or “crazy glue” is not recommended, in
case you need to remove in the future) (Ref. Fig 6).
11. Fig. 7 shows an outline of what the completed process should look like.

FIGS. 1-8
Fig 1 Fig 2
Fig3 Fig4
Fig5 Fig 6
Fig 7

Considerations For Maximum Heat Efficiency
Fig. 8
These are factors that you must consider to get the best use out of your heater:
・The intended room to be heated must be well insulated. Poor insulation will cause heat loss and
diminished heat efficiency.
・Mounting the heater near a flight of stairs will diminish efficiency, since the heat waves emitting from
the heater will constantly “fight” with cooler waves along the stairs.
・Open floor plans will be a factor, since heat is constantly being “lost” into other rooms, causing the
unit to be less efficient.
・Mounting the heater near open doorways, or doorways with excessive foot traffic will reduce
efficiency, since heat will constantly be lost through those doorways.
・Mounting the heater near/along open windows or windows that are constantly opened will cause heat
to escape and diminish full heat potential.
・Using this heater in a room larger than what the unit is intended for will diminish full heat potential.

ElectricalDiagram
To use the heater, please follow these instructions:
1. Plug in the heater.
2. Toggle the red on/off switch to the “on” position. The toggle switch should light up when powered
on.
3. Turn the toggle switch to the “off” position when you do not require heat.
4. Unplug the heater if you will be leaving it unattended for a while.
D
A
B
C

If your heater fails to operate, please follow these instructions:
Ensure that your circuit breaker or fuse is working properly.
Be sure the heater is plugged in and that the electrical outlet is working properly.
If the ON/OFF switch is not lit at ON position, contact technical support or consult with the place of
purchase immediately.
NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR HEATER, PLEASE SEE THE WARRANTY INFORMATION FOR
INSTRUCTIONS. PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HEATER YOURSELF. DOING SO MAY VOID THE
WARRANTY AND COULD CAUSE DAMAGE OR PERSONAL INJURY. IF THE PROBLEM STILL PERSISTS, PLEASE
CONTACT THE DISTRIBUTOR.
Before cleaning your heater, switch off the heater and allow it to cool. Disconnect the power cord from the
outlet. The outside of the heater can be cleaned by wiping it with a soft damp cloth and then dried. Do not
use abrasive cleaning powders or furniture polish, as this can damage the surface/ finish. To release the
heater from the wall, for cleaning or redecorating, just remove the plastic screw head cap and unscrew the
screws. Then just slide the heater off the wall.
For short term storage, just unplug the heater and safely coil up the power cord. For long term storage, you
can dismount from the wall and store, or just cover it on the wall with a cloth material.
Factory Model No.: PH-08H2
Voltage/Frequency: AC120V, 50/ 60Hz
(Please refer to the package information and be sure that your input voltage is matching with the rated input
voltage)
Tolerances on all specifications: Approximately +5%, -10%.
Recommended suitable Room Sizes:
Places with normal winter: 40 X 40 foot room
Places with cold winter: 30 X 30 foot room
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmental safe recycling.





Limited Manufacturer Warranty
90 Day Limited Warranty
LIFESMART warrants this heater against defects in materials and workmanship on functional parts, for
a period of 90 days from the original date of purchase. Your sales receipt showing the date of purchase of
the product is your proof of purchase. Keep it in a safe place for future reference.
Manufacturer Warranty
AllLIFESMART products are manufactured with the highest quality materials and are warranted to be
free from defects in material and workmanship at the time of purchase. This limited warranty applies to
products manufactured or distributed by the LIFESMART brand name, are delivered in the continental
United States, and extends to the original purchaser, or gift recipient. This warranty becomes valid at the
time of purchase and terminates either by the specified time frame listed above and/or owner transfer
(unless otherwise authorized by LIFESMART, as the manufacturer). Any extended warranties (warranties
that cover above and beyond this manufacturer warranty) that are sold through a retailer or third party, are
not directly correlated with this LIFESMART limited warranty, and may be redirected to said retailer or
third party for coverage.
Extent of Warranty
This warranty extends through the manufacturer of the product, and covers functional parts only.
Cosmetics are not covered, unless unequivocally determined it is a manufacturer/workmanship defect. Note
that surface cracks are not considered defects in material or workmanship, as they are normal characteristics
of all wood and some plastics. Unless LIFESMART was the direct shipper, shipping damage should be
addressed with the shipping company, retailer, or place of purchase, prior to making a claim to
LIFESMART, as the manufacturer.
The manufacturer's sole obligation under this warranty shall be limited to furnishing the original purchaser
replacement parts for units deemed repairable by the LIFESMART warranty department. The purchaser
may also opt to ship the product to LIFESMART to have it repaired. The purchaser will be responsible to
prepay any shipping charges (both ways), export taxes, custom duties and taxes, or any other charges
associated with the transportation of the unit. In addition, the purchaser is responsible for insuring any parts
shipped or returned, if desired. For products the warranty department deems un-repairable, or discontinued,
LIFESMART reserves the right to issue a refurbished product, or product similar in size and functionality
as a replacement for the defective unit, if available. All exchanged parts and products replaced under this
warranty will become the property of LIFESMART.LIFESMART reserves the right to change
manufacturers of replacement parts or products for use, in order to cover any existing warranty. Any parts
determined defective may asked to be returned to LIFESMART or its representatives to validate a claim.
Non-Warranty replacement parts will be warranted 30 days from the time the purchaser receives them.
The purchaser must present LIFESMART with proof of purchase documents (including the date of
purchase) if requested. Any evidence of alteration, erasing, or forgery of proof of purchase documents will
be just cause to VOID this limited warranty. Products, in which the serial number has been defaced or
removed, are not eligible for warranty coverage. Continued…

Warranty Limitations
This warranty does not apply if the unit has been subject to negligence, fabrication, misuse, abuse, or
repairs (unless authorized verbally, or in writing, by an Authorized LIFESMART Representative) alteration
by non LIFESMART authorized personnel, inappropriate installations, or any case beyond the control of
LIFESMART. Examples of warranty invalidation may also include, but are not limited to:
Use of lacquer or paints in (and around)
the heaters
Heater placed on non-approved surfaces
Electrical requirement deficiencies
(15-20 amp dedicated outlet)
Use on Extension Cords/Timers/Surge
Protectors/GFCI
Outdoor applications
Normal wear/tear/weathering
Pet/Consumer accidents
Purchases from dealers unauthorized by
LIFESMART (Authorization in writing)
Disclaimers
LIFESMART shall not be liable for any loss due to use (or misuse) of the heater or other LIFESMART
products or other incidental or consequential costs, expense or damages without irrefutable foundations.
Under no circumstances shall LIFESMART or any of its representatives be held liable for injury to any
person or damage to any property, however arising. Any implied warranty shall have duration equal of the
applicable warranty stated above. Specifications are subject to change without notice or obligation.
Legal Remedies
This limited warranty gives the original purchaser specific legal rights. Other rights may vary from state
to state.

Customer Service and Support
To Obtain Warranty Support or Advice, Please Complete Any of these Easy Steps:
Contact LIFESMART PRODUCTS Technical Support
E-mail: W[email protected]
Phone: [phone]
You will need to provide the unit's model number, serial number (located on the heater’s front
panel, rear panel, or on the box), date of purchase, retailer of purchase, a daytime phone
number, and possibly a copy of your receipt.
Be Patient, Clear, and Concise.
Describe the issue and symptoms you have for, and about the product.Acertified LIFESMART
Technical Support agent will give you an evaluation of your issue and your resolution options.
If the answer is not available at that time, you will be referred to the appropriate channels, or
given a call/e-mail back within 72 hours with an answer or resolution.
*E-Mail is the Preferred Method of Communication
Or visit us online at: www. Lifesmartproducts.com