Lifetime DOUBLE SHOT 90648 User manual

TOOLS REQUIRED TABLE OF CONTENTS
• 2+ people recommended for setup
• Videos and help guides available
Scan the code below to see how it all comes together.
http://go.lifetime.com/90648playlist
ASSEMBLY INSTRUCTIONS
MODEL #60091
DOUBLE SHOT®
ARCADE BASKETBALL
SYSTEM
MODEL 90648
THIS PRODUCT IS INTENDED FOR INDOOR USE ONLY.
BEFORE ASSEMBLY:
Icon Legend................................2
Warnings & Notices.....................3
Frame Assembly..........................4
Backboard to Rim Assembly.........9
Parts Identifier..........................i-iv
Ramp Assembly........................13
Adjusting the System................20
Maintenance..........................21
Registration........................21
Warning Stickers.......................22
Warranty................................23
(1, included)
9/16" (14 mm)
(1, included) (1)
(1)
CAUTION – ELECTRICALLY OPERATED
PRODUCT – Not recommended for Children under 3
years of age. As with all electric products, precautions should be
observed during handling and use to prevent electric shock.
WARNING – ADULT
ASSEMBLY REQUIRED:
Small parts, sharp edges and points
may be present during assembly.
CONTACT LIFETIME CUSTOMER SERVICE:
Call: 1-800-225-3865
7:00 am–5:00 pm (Monday–Friday) MST
and 9:00 am–1:00 pm Saturday MST
QUESTIONS? MODEL# AND PRODUCT ID
(you will need both when contacting us)
Model Number: 90648
Product ID:
For Customer Service in Mainland
Europe and the United Kingdom,
E-mail:[email protected]
Live Chat: www.lifetime.com
(click on “Ask An Expert” tab)
Video Instructions:
www.youtube.com/lifetimeproducts
COPY

2
1182656 C 11/17/2017
• Indicates the parts to be used for a section.
• Indicates special heed should be taken when reading.
• Indicates the hardware to be used for a section.
• Indicates the tools to be used for a section.
• Indicates no hardware required for a specific page.
• Indicates no parts required for a specific section.
• Indicates to use/not to use an electric drill for a specific step.
ICON LEGEND
• Indicates the use of a Centerlock Nut. A Nut with this marking will require some effort to tighten.
This hardware was designed with this feature in order to prevent loosening later.
COPY

3
WARNINGS & NOTICES
Most injuries are caused by misuse and/or not following instructions. Use caution when using this product.
To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing
material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware
identifier and parts list in this document. Proper and complete assembly, use and supervision are essential for proper operation and to reduce the
risk of accident or injury. A high probability of serious injury exists if this product is not installed, maintained, and operated properly.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
• If using a ladder during assembly, use extreme caution.
• Two capable adults are recommended for this operation.
• Assemble the pole sections properly. Failure to do so could cause the pole sections to separate during play or transport.
• The power adaptor should be periodically examined for potential hazards.
• Any potentially hazardous parts must be repaired or replaced immediately.
• Do not allow the system or any of the components to get wet. Keep the system in a climate-controlled low-humidity environment.
SAFETY INSTRUCTIONS
CAUTION – UPRIGHT STORAGE OF THE PRODUCT:
When storing the Double Shot Arcade Basketball System in the upright
position, make sure the back of the backboard is up against a wall or
other reasonable support to prevent the system from falling over, which
could result in personal injury or property damage.
ELECTRICAL RATING 5.9V –Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium)
batteries.
COPY

4
Metal Parts
Hardware Blister Pack
PARTS REQUIRED
HARDWARE REQUIRED
FRAME ASSEMBLY
1
ETX (x2)
ETZ (x4)
ETZ (x2)
EYF (x1)
EUC (x3)
EUD (x1)
EUA (x9)
EUA (x2)
EUB (x3)
ETY (x2)
TOOLS REQUIRED
9/16" (14 mm)
BMA (x1)
BMB (x2)
ETL (x2)
BMF (x2)
BLT (x2)
BLZ (x2)
BLY (x2)
R
BMC (x2)
ETS
EYF (x1)
BLU (x1)
L
EXV (x1)
BPW (x1)
BPW (x1)
BMK (x2)
1
ETS 2
COPY

5
• Attach the Bottom Brace (BLU) to the Right Bottom Leg
(BMA) and Left Bottom Leg (EXV) with the hardware
shown.
TOOLS AND HARDWARE REQUIRED
XSECTION 1 (CONTINUED)
EXV
ETX ETX
ETY
ETY
ETZ ETZ
EUA EUA
BMA
BLU
1.1
1.2
EXV
BMA
BMB
BMB
• Attach the Bottom Legs (BMA & EXV) to the Rear Top Leg Assemblies as shown. Press down on the push button and insert
the swaged end of the Rear Bottom Leg into the Rear Middle Leg (BMB) until the push button snaps into the hole.
Snap push button
into hole
Press down on
push button
ETX (x2)
ETZ (x2)
EUA (x2) ETY (x2)
EYF (x1)
9/16" (14 mm)
• If you have trouble with this section, scan the
QR code below to view the assembly video.
• http://go.lifetime.com/doubleshot-frame
R
L
BPW (x1)

6
TOOLS AND HARDWARE REQUIRED
1.3
XSECTION 1 (CONTINUED)
• Align the holes in the Top Arm (ETL) and Rear Top Leg (BMC), then secure them with the hardware shown.
Only finger-tighten the hardware for now.
ETL
BMC
BMC
BMC
• Attach the Rear Top Leg Assemblies to Rear Middle Leg (BMB) as shown. Press down on the push button and insert the
swaged end of the Rear Top Leg into the Rear Middle Leg (BMB) until the push button snaps into the hole indicated.
1.4
90-inch high ceilings
Press down on
push button
BMB
BMB
BMK (x2)
ETZ (x2)
EUA (x2)
EUA
BMK
ETZ
EYF (x1)
9/16" (14 mm)
BPW (x1)
!• The hardware for this step is found in the Section 2
portion of the hardware blister pack. Repeat this step
to assemble the remaining Top Arm and Rear Top Leg.
Ceilings between
84 and 90 inches
!• The Double Shot Arcade Basketball System has two height settings. For ceilings that are
90 inches or more from the floor, set the push button to rest in the first hole in the Rear
Middle Leg (BMB). For ceilings between 84 and 90 inches, use the second hole.
The Double Shot was not intended for use with ceilings under 84 inches.
BMB
BMC

7
TOOLS AND HARDWARE REQUIRED
• Attach the Rear Cross Braces (BLZ) to the Rear Leg Assemblies and the Bottom Brace (BLU) with the hardware shown.
1.5
XSECTION 1 (CONTINUED)
BLZ
BLZ
BLZ
BLU
EUB
EUB
EUB
EUA
EUA
EUA
ETZ
ETZ
ETZ (x2) EUA (3)
EUB (x3)
• Press down on the push button on the Side Leg (BMF) and insert the swaged end of it into the Upper Side Leg (BLY) until the
push button snaps into the hole indicated. Repeat this step to complete the other Side Leg Assembly.
1.6
Snap push button
into hole Press down on
push button
BLY BMF
BLY BMF
EYF (x1)
9/16" (14 mm)
BPW (x1)

8
TOOLS AND HARDWARE REQUIRED
• Turn the Frame over and attach the Side Leg Assembly to the frame with the hardware as shown.
• Attach the other Side Leg Assembly. Attach a Fold-Up Plate (BLT) to each side of the Bottom Brace (BLU).
1.7
1.8
XSECTION 1 (CONTINUED)
BMF
EUC
EUC
EUA
EUA
BLY
EUC (x3)
EUA (x4)
EUD (x1)
BMF
EUC
EUA
EUD
BLT
BLT
BLY
EUA
BLU
BLU
EYF (x1)
9/16" (14 mm)
BPW (x1)

9
2BACKBOARD TO RIM ASSEMBLY
Metal Parts
Hardware Blister Pack
PARTS REQUIRED
HARDWARE REQUIRED
AJI (x1)
AKZ (x2)
BLQ (x1)
ALX (x2)
TOOLS REQUIRED
(1)
(1)
BPW (x1)
Plastic Parts
ETZ (x8)
BMN (x2)
BNZ (x4) BOA (x4) EUE (x8)
BMJ (x8) EUA (x8)
9/16" (14 mm)
EYB (x4)
EYF (x1)
ETS 2

10
XSECTION 2 (CONTINUED)
TOOLS AND HARDWARE REQUIRED
BLQ
2.1 • Remove and discard the plastic shield from the Electronic Scoreboard (BLQ), and snap the four Sensors (EYB) into
place as shown.
EYB
EYB
EYB
EYB
• If you have trouble with this section, scan the code below to view a video on on its assembly.
• http://go.lifetime.com/doubleshot-backboard