Lightmybricks 75349 User manual

LEGO®STAR WARS CAPTAIN REX HELMET
#75349 LIGHT KIT
INSTALLATION GUIDE

2
Light My Bricks
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE
LEGO®STAR WARS CAPTAIN REX HELMET
75349 INSTALLATION GUIDE
Hi There!
We’re here to help you get started on the LEGO®
Star Wars Captain Rex Helmet 75349 Light Kit.
This PDF details the instructions for the LED light kit only.
If you run into any issues, please refer to the
troubleshooting section towards the end of this guide.
Have fun and enjoy!
INSTALLATION GUIDE

PACKAGE CONTENTS 3
PACKAGE CONTENTS:
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE
•1 x Blue 30cm Large Bit Light
•1 x Cool White 30cm Large Bit Light
•3 x Cool White 30cm Bit Light
•1 x USB Power Cable
1 x 2-Port Expansion Board
1 x 6-Port Expansion Board
2 x Plate 1 x 6 - Black
4 x Plate 1x1 Mod Rounded w Handle - Black
2 x Arm Skeleton, Bent with Clips (Horizontal Grip) - Black
2 x Round Plate 1x1 w/ Open Stud - Black
1 x 30cm Connecting Cable
Individual Bags Mixed Components
Connecting Cables
USB Power Cable
1x USB Power Cable
(Power Source not Included)

CONTENTS 4
Contents
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE
Before You Begin 5
Blueprint 10
Instructions 11
Final Product 24
Troubleshooting 25
Contact 29

BEFORE YOU BEGIN 5
Before You Begin
Laying cables in between
and underneath bricks
Cables can fit in between and underneath
LEGO®bricks, plates, and tiles providing
they are laid correctly between the LEGO®
studs. Do NOT forcefully join LEGO®
together around cables; instead ensure
they are laying comfortably in between
each stud.
CAUTION: Forcing LEGO®to connect over
a cable can result in damaging the cable
and light.
Connecting Cable
Connectors To Expansion
Boards
Take extra care when inserting connectors
to ports of Expansion Boards. Connectors
can be inserted only one way. With the
expansion board facing up, look for the
soldered “=” symbol on the left side of the
port. The connector side with the wires
exposed should be facing toward the
soldered “=” symbol as you insert into the
port. If a plug won’t fit easily into a port
connector, do not force it.
Incorrectly inserting the connector can re-
sult in bent pins inside the port or possible
overheating of the expansion board when
connected.
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE

BEFORE YOU BEGIN 6
Before You Begin
Connecting Cable
Connectors To Strip Lights
Take extra care when inserting connectors
to ports on the Strip Lights. Connectors
can be inserted only one way. With the
Strip Light facing up, ensure the side of
the connector with the wires exposed is
facing down. If a plug won’t fit easily into
a port connector, don’t force it. Doing so
will damage the plug and the connector.
Connecting Micro Cable
Connectors To Micro
Expansion Board Ports
Take extra care when inserting the
micro connectors to micro ports of Micro
Expansion Boards. Connecting Micro Bit
Lights to Micro Expansion Boards is similar
to connecting lights and cables to Strip
Lights. With the expansion board facing
up, ensure the side of the connector with
the wires exposed is facing down. If a plug
won’t fit easily into a port connector, do
not force it. Use your fingernail to push the
plastic part of the connector to the micro
port.
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE

BEFORE YOU BEGIN 7
Before You Begin
Installing Bit Lights Under
Lego® Bricks And Plates
When installing Bit Lights under LEGO®
pieces, ensure they are placed the correct
way up (Yellow LED component exposed).
You can either place them directly on top of
LEGO®studs or in between.
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE

BEFORE YOU BEGIN 8
Before You Begin
Disconnect
Used when you need to
remove a LEGO piece/ section
or LMB component.
Twist/ Braid
Seen when a set of cables
need to be grouped and
twisted together.
Directional
Used to show where to route
cables, place components, or
move them.
Power On Test
Found at the end of a major
step to test the lights. Will be
located in the top left corner.
Bend/Pivot
Used when a component
needs to be bent, or part
folded or pivoted.
Note
Notes will be found alongside
the instruction photos and
explain what to do.
Connect
Used when you need to
connect a LEGO piece or LMB
component.
Turn/ Flip
Will be found in the top left
corner when the set needs to
be rotated or flipped.
Light Kit Component
This is the most important image
format as it indicates which part
to use from the Light Kit. Make
sure you pay close attention to
which part is shown.
The Symbols Used In This Guide
When going through the following guide you will
come across symbols and formats that will assist
with the installation of your light kit. Take notice of
them as each has a specific purpose.
White 30cm Bit Light
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE

BEFORE YOU BEGIN 9
Before You Begin
Disconnect Note
The red coloured note is
used when the topic focuses
on a component being
disconnected or like here, the
removed pieces.
Connect Note
The green coloured note is
used when the topic focuses
on a component being
connected, like the shown
Power Bank.
General Note
This is a sample note that is
used anywhere in this guide. It
will explain a dicult section
where photos are hard to
illustrate or easily confused.
NOTE
Connect to a 5V USB Power Bank,
5V USB Wall Adaptor, or USB to AA
Battery Pack (sold separately)
NOTE
You should have these parts left
over that were removed from the
LEGO set
NOTE
Take the 5cm Connecting Cable
from the 4-Port Micro Expansion
Board and route it into the “IN”
port of the Flicker Eects Board
x2
Connect Focus
Used to highlight a hard to
see area where a component
is being connected.
Disconnect Focus
Used to highlight a hard to
see area where a component
is being disconnected.
General Focus
Used to highlight a hard to
see area where a component
needs to be acted on.
Repeat Step
Repeat the previous step eg.
Make a spotlight, then make a
second spotlight.
Removed Pieces
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE

BLUEPRINT 10
BLUEPRINT
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE

INSTRUCTIONS 11
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE
INSINSTRTRUCUCTIONSTIONS
TTo ensuro ensure a smooe a smooth instth installation oallation off yyourour lighlightt kitkit, please r, please read and fead and folloolloww
each steach step cep carareefullfullyy. I. Iff yyou run inou run inttooanany issues, please ry issues, please reefferer tto the onlineo the online
trtroubleshoooubleshooting guideting guide..
Wenn Sie Probleme mit Ihrem Light My Bricks-Set haben, sehen Sie sich unser Video zur Fehlerbehebung an oder
lesen Sie die Auflistung der häufigsten Ursachen, die Ihnen bei der Fehlersuche helfen hier.
Si vous rencontrez des problèmes avec votre kit Light My Bricks, regardez notre vidéo de dépannage ou consultez la
liste des causes les plus fréquentes pour vous aider à les résoudre ici.
Se si verificano problemi con il set Light My Bricks, guardare il nostro video per la risoluzione dei problemi o leggere
l'elenco delle cause più comuni per la risoluzione dei problemi qui.

INSTRUCTIONS 12
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE
1

INSTRUCTIONS 13
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE
2 3
Round Plate 1x1 Open Stud - Black
2 x Plate 1x1 Mod Rounded W/
Handle - Black
Cool White 30cm Large Bit Light

INSTRUCTIONS 14
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE
Arm Skeleton, Bent W/ Clips
Horizontal Grip - Black
2 x Plate 1x1 Mod Rounded W/
Handle - Black
Plate 1x6 - Black
5
Round Plate 1x1 Open Stud - Black
2 x Plate 1x1 Mod Rounded W/
Handle - Black
Blue 30cm Large Bit Light

INSTRUCTIONS 15
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE
6
Arm Skeleton, Bent W/ Clips
Horizontal Grip - Black
Plate 1x6 - Black
NOTE
Connect both of the spotlight
assemblies to the base. Ensure
the Blue Bit Light is on the left,
and the Cool White on the
right.

INSTRUCTIONS 16
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE
72-Port Expansion BoardUSB Power Cable
30cm Connecting Cable
NOTE
Thread the 30cm Connecting
Cable through the following
gap. Straighten the cable if you
are having trouble.
NOTE
Continue to thread the 30cm
Connecting Cable all the way
through while positioning the
2-Port Expansion Board as
shown

INSTRUCTIONS 17
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE
8

INSTRUCTIONS 18
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE
9
6-Port Expansion Board
Cool White 30cm Bit Light

INSTRUCTIONS 19
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE
10

INSTRUCTIONS 20
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®STAR WARS CAPTAIN REX HELMET 75349 LIGHT KIT INSTALL GUIDE
11
Cool White 30cm Bit Light
12