Lightmybricks 75244 User manual

The following page is the instructions for the Light My Bricks LEGO Star Wars
Tantive IV (75244) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow
each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are
wishing to purchase the Light My Bricks LEGO Star Wars Tantive IV (75244) LED
light kit , please click here to view the product page
Light My Bricks: LEGO Star Wars Tantive IV
75244 Lighting Kit

Package Contents:
11x White 30cm Bit Lights
10x Cool White 30cm Bit Lights
4x Red 30cm Bit Lights
2x Flashing Red 30cm Bit Lights
4x 6-Port Expansion Boards
1x 8-Port Expansion Boards
1x 12-Port Expansion Boards
1x Multi Effects Board
1x Gun Effects Board
1x Set of Wireless Power Connectors (possitive and negative)
2x 5cm Connecting Cables
3x 15cm Connecting Cables
1x 30cm Connecting Cable
6x Adhesive Squares
1x USB Power Cable 30cm
LEGO Pieces:
4x Trans Clear Round Plate 1×1
1x Trans Clear Plate 1×2
Important things to note:
Laying cables in between and underneath bricks

Cables can fit in between and underneath LEGO® bricks, plates, and tiles
providing they are laid correctly between the LEGO® studs. Do NOT forcefully
join LEGO® together around cables; instead ensure they are laying comfortably
in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the
cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards.
Connectors can be inserted only one way. With the expansion board facing up,
look for the soldered “=” symbol on the left side of the port. The connector side
with the wires exposed should be facing toward the soldered “=” symbol as you
insert into the port. If a plug won’t fit easily into a port connector, do not force it.

Incorrectly inserting the connector can can result in bent pins inside the port
or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure
the side of the connector with the wires exposed is facing down. If a plug won’t
fit easily into a port connector, don’t force it. Doing so will damage the plug and
the connector.
Installing Bit Lights under LEGO® bricks
and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the

correct way up (Yellow LED component exposed). You can either place them
directly on top of LEGO® studs or in between.
OK, Let’s Begin!
1.) We will first install lights to the cockpit. Start by disconnecting the roof
section on each side, then disconnect the following middle sections as shown
below:

Disassemble the middle section as shown below, then take the red and trans
dark clear pieces.

2.) Take 2x Cool White 30cm Bit Lights and with the cables facing the right
side, place both of them over the studs of the red plate. Secure them in place by
reconnecting the trans dark clear plates over the top. The 2 LEDs should fit
nicely inside the studs of the trans dark clear plates.

Reconnect the following section on top, then flip it over and push the cables
down into the corner before reconnecting it to the two white arch bricks. Lay
the two cables down the middle in between studs before reconnecting the
right section over the top of the cables.

Flip this section over and ensure both cables are tucked in between white
bricks, then flip it back over and reconnect the middle section on top.

3.) Take a new Cool White 30cm Bit Light and using an Adhesive Square, stick
it underneath the middle section in the below position with cable facing the
back.