Lightmybricks LEGO 75277 User manual

LEGO® BOBA FETT HELMET
#75277 LIGHT KIT
INSTALLATION GUIDE

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
2
Light My Bricks
LEGO® BOBA FETT HELMET #75277 LIGHT KIT
INSTALLATION GUIDE
Hi There!
We’re here to help you get started on the LEGO®
Boba Fett Helmet (75277) Light Kit.
This PDF details the instructions for the LED light kit only.
If you run into any issues, please refer to the
troubleshoot-ing section towards the end of this guide.
Have fun and enjoy!
INSTALLATION GUIDE

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
PACKAGE CONTENTS 3
PACKAGE CONTENTS: LEGO PIECES:
2 x Large Cool White 30cm Bit Lights
3 x Large Red 30cm Bit Lights
1 x Red 30cm Bit Light
8-Port Expansion Board
1 x USB Power Cable
(Power Source not Included)
•2 × Black Plate 1x6
•1 x Trans Red 1x1 Round Plate
•2 × Black Round Plate 1x1 w Open Stud
•2 × Black Arm Skeleton, Bent w Clips (Horizontal Grips)
•4 × Black Plate 1x1 Modified Rounded w Handle

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
CONTENTS 4
Contents
Before You Begin 5
Instructions 9
Final Product 16
Troubleshooting 17
Contact 22

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
BEFORE YOU BEGIN 5
Before You Begin
Laying cables in between
and underneath bricks
Cables can fit in between and underneath
LEGO® bricks, plates, and tiles providing
they are laid correctly between the
LEGO® studs. Do NOT forcefully join
LEGO® together around cables; instead
ensure they are laying comfortably in
between each stud.
CAUTION: Forcing LEGO® to connect over
a cable can result in damaging the cable
and light.
Connecting Cable
Connectors To Expansion
Boards
Take extra care when inserting connectors
to ports of Expansion Boards. Connectors
can be inserted only one way. With the
expansion board facing up, look for the
soldered “=” symbol on the left side of the
port. The connector side with the wires
exposed should be facing toward the
soldered “=” symbol as you insert into the
port. If a plug won’t fit easily into a port
connector, do not force it.
Incorrectly inserting the connector can
can result in bent pins inside the port or
possible overheating of the expansion
board when connected.

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
BEFORE YOU BEGIN 6
Before You Begin
Connecting Cable
Connectors To Strip Lights
Take extra care when inserting connectors
to ports on the Strip Lights. Connectors
can be inserted only one way. With the
Strip Light facing up, ensure the side of
the connector with the wires exposed is
facing down. If a plug won’t fit easily into
a port connector, don’t force it. Doing so
will damage the plug and the connector.
Connecting Micro Cable
Connectors To Micro
Expansion Board Ports
Take extra care when inserting the
micro connectors to micro ports of Micro
Expansion Boards. Connecting Micro Bit
Lights to Micro Expansion Boards is similar
to connecting lights and cables to Strip
Lights. With the expansion board facing
up, ensure the side of the connector with
the wires exposed is facing down. If a plug
won’t fit easily into a port connector, do
not force it. Use your fingernail to push the
plastic part of the connector to the micro
port.

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
BEFORE YOU BEGIN 7
Before You Begin
Installing Bit Lights Under
Lego® Bricks And Plates
When installing Bit Lights under LEGO®
pieces, ensure they are placed the correct
way up (Yellow LED component exposed).
You can either place them directly on top of
LEGO® studs or in between.

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
INSTRUCTIONS 8
INSTRUCTIONS
To ensure a smooth installation of
your light kit, please read and follow
each step carefully. If you run into
any issues, please refer to the online
troubleshooting guide.
INSTRUCTIONS
LEGEND:DISCONNECT DIRECTIONAL
LEGENDE:TRENNEN DIRECTIONAL
LÉGENDE:DÉCONNECTER DIRECTIONNEL
LEGGENDA: SCOLLEGARE
CONNECT / RECONNECT
VERNINDEN / WIEDERVERBINDEN
CONNECTER / RECONNECTER
CONNETTI / RICONNETTI
TURN / FLIP
WENDEN / KIPPEN
TOUR / INCLINAISON
ROTARE / INCLINARE DIREZIONALE
TWIST / BRAID
DREHEN / VERDREHEN
TORSION / TRESSER
TWIST / TRECCIA
POWER ON / TEST
EINSCHALTEN / TESTEN
POWER ON / TEST
POWER ON / TEST

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
INSTRUCTIONS 9
1
Legend DISCONNECT CONNECT /
RECONNECT TURN / FLIP DIRECTIONAL TWIST / BRAID POWER ON TEST NOTE ICON
Red 30cm Bit Light
Trans Red 1x1 Round Plate

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
INSTRUCTIONS 10
2
Legend DISCONNECT CONNECT /
RECONNECT TURN / FLIP DIRECTIONAL TWIST / BRAID POWER ON TEST NOTE ICON
2x Large Red 30cm Bit Light
3

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
INSTRUCTIONS 11
4
Legend DISCONNECT CONNECT /
RECONNECT TURN / FLIP DIRECTIONAL TWIST / BRAID POWER ON TEST NOTE ICON
After pulling the
wire towards the
back of the helmet,
re-connect the piece
you just removed
After pulling the
wire towards the
back of the helmet,
re-connect the piece
you just removed

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
INSTRUCTIONS 12
5
6
Legend DISCONNECT CONNECT /
RECONNECT TURN / FLIP DIRECTIONAL TWIST / BRAID POWER ON TEST NOTE ICON
Connect to a
USB, Power Bank,
USB to AA Battery
Pack or USB Wall
Adaptor (each sold
separately)
If you experience any issues with the lights not working and suspect an issue with a component, please try a dierent port on the expansion board to verify where the fault lies (with the light or
expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues in our troubleshooting section.
Large Red 30cm Bit Light
8-Port Expansion Board
USB Power Cable

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
INSTRUCTIONS 13
7
Legend DISCONNECT CONNECT /
RECONNECT TURN / FLIP DIRECTIONAL TWIST / BRAID POWER ON TEST NOTE ICON
Black Arm Skeleton, Bent w
clips (Horizontal Grips)
2x Black Modified Plate
Rounded w Handle
Large Cool White
30cm Bit Light
Black Round Plate 1x1
w Open Stud 2x
2x Black 1x6 Plate
Thread the wires
through the holes as
shown

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
INSTRUCTIONS 14
8
Legend DISCONNECT CONNECT /
RECONNECT TURN / FLIP DIRECTIONAL TWIST / BRAID POWER ON TEST NOTE ICON
Lay the spotlight
wire inbetween the
following studs be-
fore securing them
Lay the spotlight
wire inbetween the
following studs be-
fore securing them

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
INSTRUCTIONS 15
9
Legend DISCONNECT CONNECT /
RECONNECT TURN / FLIP DIRECTIONAL TWIST / BRAID POWER ON TEST NOTE ICON

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
FINAL PPRODUCT 16
FINAL PRODUCT
This finally completes installation of the Light My
Bricks Boba Fett Helmet 75277 Light Kit.

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
TROUBLESHOOTING 17
TROUBLESHOOTING
Light My Bricks lighting
kits contain individual
components that are very
small and can be easily
damaged if not handled
correctly.
To prevent unnecessary
damage to components,
we highly recommend that
the User Guide section,
“Important things to note”
is read carefully. Follow the
handling procedures in the
User Guide to help prevent
faults and damages to your
Light My Bricks components.
If you are experiencing
issues with your Light
My Bricks set, watch our
troubleshooting video
here or read on for a list of
common causes to help you
troubleshoot.

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
TROUBLESHOOTING 18
Troubleshooting
Firstly, ensure that the
baeries have power using a
baery charge gauge.
If the baeries have no power,
replace the baeries.
If the baeries still have
power, check to see if the
baeries have been inserted
correctly into the baery
pack.
Check For CR2032 Baeries
Using The Flat Baery Pack
Inside the battery pack is a symbol
indicating which side the (round) CR2032
battery should be inserted. Check that
the “+” side of the battery pack has
the battery with the “+” symbol facing
downwards.
On the opposite side, the “-” side of the
battery pack should have the battery
flipped upside down, that is the “+” symbol
facing upwards
CR2032

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
TROUBLESHOOTING 19
Troubleshooting
Check For Cr2032 Baeries
Using The Round Baery
Pack
Inside the battery pack is a symbol indicating
which side the (round) CR2032 battery should
be inserted. In this case, for the stacked
battery pack, ensure that BOTH batteries
have the “+” symbol facing upwards.
Check for AA baeries
using the AA baery pack
Inside the battery pack are symbols
indicating which direction the AA battery
should be inserted. The flat side of the
battery should be paired with the spring
side of the battery pack.
If the batteries have been installed
correctly and your kit still isn’t operating
correctly, the next step is to check the
wiring.
CR2032

LEGO BOBA FETT HELMET 75277 LIGHT KIT INSTALL GUIDE
TROUBLESHOOTING 20
Troubleshooting
In order for Light My Bricks components to fit
in between and underneath LEGO® bricks, the
components need to be very small. Due to this
nature, Light My Bricks components can be
easily damaged when not handled correctly.
Be careful when removing unpacked
components out of the packaging and ensure
not to forcibly pull at the wires as this can
damage the soldering that attach the wires to
the LEDs.
If the wiring is detached from the LED itself, the
light will not operate.
When connecting lights to your LEGO set, check
that there are no pinched wires underneath
or in between bricks and plates. When the
wires are pinched and the exposed wires are
touching each other, this can cause a crosswire
and the lights to not function correctly.
Check Your Wires