Lightmybricks Old Fishing Store Lighting Kit 103041 User manual

lightmybricks
User Guides for Light My Bricks LED Lighting Kits for LEGO®
Nov 6 · 11 min read
Light My Bricks: Old Fishing Store
Lighting Kit
Here is the instructions document for the LEGO Old Fishing Store LED
lighting kit. Please read and follow the steps carefully to ensure this lighting
kit is installed properly.
. . .

Package contents:
• 4x White 15cm Bit Lights
• 3x White Strip Lights
• 1x 6-Port Expansion Board
• 1x 30cm Connecting Cable
• 1x 15cm Connecting Cable
• 1x 5cm Connecting Cable
• AA Battery Pack (Requires 3x AA Batteries)
LEGO pieces
• 2x Plates 1x6
. . .
Important things to note:
Laying cables in between and underneath bricks
Cables can t in between and underneath LEGO® bricks, plates, and tiles
providing they are laid correctly between the LEGO® studs. Do NOT
forcefully join LEGO® together around cables; instead ensure they are laying
comfortably in between each stud.

CAUTION: Forcing LEGO® to connect over a
cable can result in damaging the cable and
light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards.
Connectors can be inserted only one way. With the expansion board facing
up, look for the soldered “=” symbol on the left side of the port. The
connector side with the wires exposed should be facing toward the
soldered “=” symbol as you insert into the port. If a plug won’t t easily into a
port connector, do not force it.

Incorrectly inserting the connector can can
result in bent pins inside the port or possible
overheating of the expansion board when
connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up,
ensure the side of the connector with the wires exposed is facing down. If a
plug won’t t easily into a port connector, don’t force it.
Doing so will damage the plug and the connector.

Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the
correct way up (Yellow LED component exposed). You can either place them
directly on top of LEGO® studs or in between.
. . .
OK, Let’s Begin!
1.) Start by removing the upper level as well as the main roof section.

Remove the lamp section and then disassemble as per below.
2.) Take a White 15cm Bit Light and then thread the connector side through
the hole on top of the bottom piece. Thread it all the way through until
the LED is at against the top of the piece.

You may need bend the LED slightly so that it sits at against the top of the LEGO piece
Reconnect the top section to secure the LED in place.

Reconnect the lamp back to the desk inside the building ensuring the cable
is facing the front left corner so that it is not visible if you look in the
window.

3.) Take the top section of the Old Fishing Store and remove the roof.
Disconnect the at clear 2x2 boat stud piece from underneath the roof and
then take a White 15cm Bit Light and place it directly in the centre.
Reconnect the at clear boat stud piece directly over the Bit Light to secure it
in place.

Ensure the LED is the correct way facing up
Secure the cable by laying it underneath the bottom brown 1x6 plate.

Ensure the cable is laid in between studs
4.) Before reconnecting the roof, thread the Bit Light cable from theroof
down and then pull it out from the bottom of the top section.

5.) Remove the lamp from the bottom of this section and thendisconnect
the black round stud from underneath.

Take another White 15cm Bit Light and thread the connector side through
the top of the black round plate. Thread it all the way through until the LED
is at against the top of the plate then reconnect the top section of the lamp.

You may need bend the LED slightly so that it sits at against the top of the LEGO piece
6.) Reconnect the lamp to the outside of the upper level and then laythe
cable and secure it underneath the brown LEGO 1x6 plate.

7.) Take the 6-Port Expansion Board and then connect the two bit light
cables to spare ports.
8.) Take the 30cm Connecting Cable and connect one end to the expansion
board.

9.) Take the AA Battery Pack and insert 3x AA Batteries to it before placing
it at the back of the old shing store in the following location. It should
seat neatly in between the back of the building and rail.
10.) Take the entire upper level above the set and take the bit lightcable
from the lamp inside and connect it to the expansion board.

Take the battery pack cable and connect it to the expansion board.
Tuck the expansion board and excess cables (except for the 30cm cable) up
inside the upper level as per below.

Before reconnecting the upper level back to it’s original position, ensure the
30cm connecting cable is pulled across to the right section of the building.

VIEW FROM THE BACK: Ensure 30cm cable is accessible after reconnecting upper level Test
the lights we have installed so far by turning ‘ON’ the battery pack.

11.) Remove the lamp from the right side of the building and
thendisconnect the black round stud from underneath.