Lightmybricks LEGO Star Wars Slave 1 75060 Lighting Kit User manual

LightMyBricks
InstallationInstructionsforLightMyBricksLEDLightingKits
Jul20 ·20minread
LightMyBricks:LEGOStarWarsSlave1
75060LightingKit
The following page is the instructions for the Light My Bricks LEGO
Star Wars Slave 1 (75060) LED light kit.
To ensure a trouble-free installation of your light kit, please read and
follow each step carefully.
If you run into any issues, please refer to the online troubleshooting
guide.
To download this instructions guide in PDF format please click here.
Pleasenote:ThispagelistsinstructionsfortheLED
lightkitonly.IfyouarewishingtopurchasetheLight
MyBricksLEGOStarWarsSlave1(75060)LEDlight
kit,pleaseclickheretoviewtheproductpage
...
PackageContents:
13x White 30cm Bit Lights•

11x Blue 30cm Bit Lights
2x Flashing Red 30cm Bit Lights
2x 12-Port Expansion Boards
1x 8-Port Expansion Board
1x Multi Eects Board
3x 5cm Connecting Cables
1x AA Battery Pack
LEGO Pieces:
1x Trans Clear Round Plate 1x1
9x Trans Light Blue Round Plate 1x1
•
•
•
•
•
•
•
•
•
...
Importantthingstonote:
Layingcablesinbetweenandunderneathbricks
Cables can t in between and underneath LEGO® bricks, plates, and
tiles providing they are laid correctly between the LEGO® studs. Do
NOT forcefully join LEGO® together around cables; instead ensure they
are laying comfortably in between each stud.

CAUTION:ForcingLEGO®toconnectoveracable
canresultindamagingthecableandlight.
ConnectingcableconnectorstoExpansionBoards
Take extra care when inserting connectors to ports of Expansion
Boards. Connectors can be inserted only one way. With the expansion
board facing up, look for the soldered “=” symbol on the left side of the
port. The connector side with the wires exposed should be facing
toward the soldered “=” symbol as you insert into the port. If a plug
won’t t easily into a port connector, do not force it.
Incorrectlyinsertingtheconnectorcancanresultin
bentpinsinsidetheportorpossibleoverheatingof

theexpansionboardwhenconnected.
InstallingBitLightsunderLEGO®bricksandplates.
When installing Bit Lights under LEGO® pieces, ensure they are placed
the correct way up (Yellow LED component exposed). You can either
place them directly on top of LEGO® studs or in between.
...
OK, Let’s Begin!
1.) Start by disconnecting the front window section as well as sections
from the right side using the LEGO removal tool as per below:

2.) Take a Flashing Red 30cm Bit Light and bend the component part
slightly on a 90 degree angle so that it is facing upward.

Thread the Bit Light through the upper hole on the right side of cockpit.
Pull the cable out slightly from the inside as per below:
Lay the cable in between studs of the outside and then reconnect the
middle part of the right section.

From the inside of Slave 1, push the Flashing Red Bit Light toward the
inside of the hole.
3.) Thread the connector side of the cable down behind the side of the
ship and then reconnect sections of the right side which we removed
earlier.

4.) Repeat previous steps to install another Flashing Red 30cm Bit
Light to the left side of the cockpit.

5.) Remove the middle and the left and right side sections of Slave 1 as
per below:
Take the cable from the left Flashing Red Bit Light and then thread it
through the middle and pull it out from the right side so that both
cables are together