Lightmybricks Blade Runner Spinner User manual

BLADE RUNNER SPINNER LIGHT KIT
INSTALLATION GUIDE

BLADE RUNNER SPINNER LIGHT KIT INSTALL GUIDE
INSTALLATION GUIDE 2
Light My Bricks
BLADE RUNNER SPINNER LIGHT KIT
INSTALLATION GUIDE
Hi There!
We’re here to help you get started on the LEGO®
Blade Runner Spinner Light Kit.
This PDF details the instructions for the LED light.
If you run into any issues, please refer to the troubleshoot-
ing section towards the end of this guide.
Have fun and enjoy!

BLADE RUNNER SPINNER LIGHT KIT INSTALL GUIDE
PACKAGE CONTENTS 3
PACKAGE CONTENTS: LEGO PIECES:
11 x Cool White 30cm Bit Light
2 x Cool White 15cm Bit Light
2 x Cool White 30cm Large Bit Light
6 x White 30cm Bit Light
2 x Blue 30cm Bit Light
2 x Red 30cm Bit Light
1 x Rotating 30cm Bit Light
3 x 6-Port Expansion Board
1 x 8-Port Expansion Board
4 x Adhesive Squares
• 1 x 1/2 Technic Pin
• 4 x Grey 1x1 Plate Modified w/ Open O Horizontal Grip
• 2 x Trans Clear 1x2 Tile
• 6 x Trans Clear 1x1 Round Plate
1 x Rotating Sequence Board (RSB)
2 x 5cm Connecting Cables
2 x 30cm Connecting Cable
1 x USB Power Cable
(Power Source not Included)

BLADE RUNNER SPINNER LIGHT KIT INSTALL GUIDE
CONTENTS 4
Contents
Before You Begin 5
Instructions 9
Final Product 38
Troubleshooting 39
Contact 44

BLADE RUNNER SPINNER LIGHT KIT INSTALL GUIDE
BEFORE YOU BEGIN 5
Before You Begin
Laying cables in between
and underneath bricks
Cables can fit in between and underneath
LEGO® bricks, plates, and tiles providing
they are laid correctly between the
LEGO® studs. Do NOT forcefully join
LEGO® together around cables; instead
ensure they are laying comfortably in
between each stud.
CAUTION: Forcing LEGO® to connect over
a cable can result in damaging the cable
and light.
Connecting Cable
Connectors To Expansion
Boards
Take extra care when inserting connectors
to ports of Expansion Boards. Connectors
can be inserted only one way. With the
expansion board facing up, look for the
soldered “=” symbol on the left side of the
port. The connector side with the wires
exposed should be facing toward the
soldered “=” symbol as you insert into the
port. If a plug won’t fit easily into a port
connector, do not force it.
Incorrectly inserting the connector can
can result in bent pins inside the port or
possible overheating of the expansion
board when connected.

BLADE RUNNER SPINNER LIGHT KIT INSTALL GUIDE
BEFORE YOU BEGIN 6
Before You Begin
Connecting Cable
Connectors To Strip Lights
Take extra care when inserting connectors
to ports on the Strip Lights. Connectors
can be inserted only one way. With the
Strip Light facing up, ensure the side of
the connector with the wires exposed is
facing down. If a plug won’t fit easily into
a port connector, don’t force it. Doing so
will damage the plug and the connector.
Connecting Micro Cable
Connectors To Micro
Expansion Board Ports
Take extra care when inserting the
micro connectors to micro ports of Micro
Expansion Boards. Connecting Micro Bit
Lights to Micro Expansion Boards is similar
to connecting lights and cables to Strip
Lights. With the expansion board facing
up, ensure the side of the connector with
the wires exposed is facing down. If a plug
won’t fit easily into a port connector, do
not force it. Use your fingernail to push the
plastic part of the connector to the micro
port.

BLADE RUNNER SPINNER LIGHT KIT INSTALL GUIDE
BEFORE YOU BEGIN 7
Before You Begin
Installing Bit Lights Under
Lego® Bricks And Plates
When installing Bit Lights under LEGO®
pieces, ensure they are placed the correct
way up (Yellow LED component exposed).
You can either place them directly on top of
LEGO® studs or in between.

BLADE RUNNER SPINNER LIGHT KIT INSTALL GUIDE
INSTRUCTIONS 8
INSTRUCTIONS
To ensure a smooth installation of
your light kit, please read and follow
each step carefully. If you run into
any issues, please refer to the online
troubleshooting guide.

BLADE RUNNER SPINNER LIGHT KIT INSTALL GUIDE
INSTRUCTIONS 9
1
Legend DISCONNECT CONNECT /
RECONNECT TURN / FLIP DIRECTIONAL TWIST / BRAID POWER ON TEST NOTE ICON

BLADE RUNNER SPINNER LIGHT KIT INSTALL GUIDE
INSTRUCTIONS 10
2
Legend DISCONNECT CONNECT /
RECONNECT TURN / FLIP DIRECTIONAL TWIST / BRAID POWER ON TEST NOTE ICON
Cool White 30cm Large Bit Light Trans Clear 1x2 Tile
Cool White 30cm Large Bit Light Trans Clear 1x2 Tile