Lightolier Arco Oval Series Guide

LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
[phone]  FAX [phone] © 1995
Read and understand these instructions before installing fixture.
This fixture is intended for installation in accordance with the National Electrical Code and local or Federal
code specifications. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
IS:4511
0995
Instructions for Installation of ArcoOval Series Fixtures.
Page 1 of 2
NOTE:
This instruction sheet covers both compact fluorescent and incandescent fixtures. Although illustration shows compact fluorescent, the
incandescent version assembles and installs in the same manner.
NOTE:
The Backplate is provided with (4) Auxiliary Mounting Knockout
holes for direct mounting to wall surfaces. These can be used for
added security or where direct Outlet Box mounting is not
available. To remove plug in Knockout holes, follow steps 1 through
3 below. This Backplate can be mounted horizontally of vertically.
See Fig 1 below for proper orientation for type of Lens Assembly
and desired position.
1. Position blunt ended punch or awl in center of Knockout hole and
firmly hit with hammer to punch plug through. Repeat for remaining
Knockouts (Fig. 1).
Caution: Always wear eye protection (safety goggles) when
removing Auxiliary Mounting Knock-Outs.
2. Position Backplate in desired position over Outlet Box and mark
location of (4) Auxiliary Holes on wall surface.
3. Determine the appropriate mounting hardware required for type of
wall material fixture is being mounted to (i.e. toggle bolts or molly
screws for plaster or gysum board walls, wood screws, etc.)
4. Thread Crossbar Mounting Screws into Crossbar as shown in
Fig. 1.
5. Using appropriate slots in Crossbar, secure Crossbar to Outlet
Box using Outlet Box Screws (provided with Outlet Box).
6. While supporting Backplate make connections: black fixture lead
or fixture without tracer marks to hot (black) supply lead; white
fixture lead or fixture lead with tracer markers to neutral (white)
supply lead. Un-insulated wire is a ground wire and must be
connected to grounding terminals or ground lead inside Outlet Box.
Use Wire Nuts (local hardware item). Push connections back into
Outlet Box.
FIG.1
N
X.
OU
AU
T
T
N
U
O
M
U
AX.
U
E
L
E
R
FO
P
S
E
H
T
E
S
NS
S
L
EN
S
T
I
H
Wire Nut
Outlet Box
Crossbar
Outlet Box Screws
Ground Wire
Backplate
Gasket
Mounting Hole
Safety Cable
Battery Nut
Loop
Mounting Screw
Lens Assembly
Crossbar Mounting
Screws
Auxiliary Mounting
Knock-out
Position this edge of Backplate up for
horizontal mounting of these Lens Assemblies.
Position this edge
of Backplate up
for vertical
mounting of this
Lens Assembly

LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
[phone]  FAX [phone] © 1995
7. Position Backplate over Crossbar allowing Crossbar Mounting
Screws to come through Holes in Backplate. Secure Backplate
in position by installing (2) Battery Nuts over Crossbar Mounting
Screws and tighten.
8. If using Auxiliary Mounting Knockout, install the appropriate
hardware determined in step 3.
9. Position Screw through Loop in Safety Cable and thread Screw
into Mounting Boss on inside of Lens Assembly (Fig. 2).
10. Install recommended lamp(s).
11. Position Lens Assembly over Backplate making certain the
Safety Cable does not interfere with the Gasket (fig. 1).
12. Secure Lens Assembly in place by tightening the (2) Mounting
Screws on the face of Lens Assembly.
CAUTION: Maximum wattage as marked on fixture must not
be exceeded.
WARNING--(Risk of Fire) most dwellings built before 1985
have supply wire rated for 60° C. Consult a qualified
electrician before installing.
CAUTION: For wet locations, in accordance with
Underwriters Laboratories requirements, a line of caulking
compound such as acrylic latex or silicone must be placed
around the perimeter of Backplate to seal water away from
the outlet box and back openings.
IS:4511
0995 Page 2 of 2
Instructions for Installation of ArcoOval Series Fixtures.
Glass
Mounting Boss
Lens Assembly
Loop
Mounting
Screw
Safty
Cable
FIG. 2
Inside Lens Assembly