Lightolier Lytecaster 1004IC User manual

Lightolier a Genlyte company www.lightolier.com
631 Airport Road, Fall River, MA 02720 • [phone] • Fax [phone]
We reserve the right to change details of design, materials and finish.
© 2007 Genlyte Group LLC • I0407
Job Information Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
Lytecaster®Recessed Downlighting 1004IC
Page 1 of 1 5" Aperture 0Incandescent Convertible IC/Non-IC Frame-In Kit
5" Aperture: Complete Fixture consists of Reflector Trim & Frame-In Kit. Select each separately.
Frame-In Kit Reflector Trims — See Individual Reflector Trim Specification Sheets
Open Downlight Adjustable
Anodized Anodized Satin Baffles Basic Eyeball Enclosed Open Wall
Reflector Cone Cone White Diffusers Wet Location Washer
1004IC 1045 1012 1008 1005 1071 1022 1021* 1081CD 1085*
1004ICQ** 1046 1012NM 1008NM 1005NM 1022WH 1024* 1081WH
1004ICN 1046CD 1013 1010 1005WH 1082 1177LX
1004ICNQ** 1013BK 1010NM 1005BNM 1088 1178LX
1013CD 1076 1088GW 1090*
1013NM 1076WH 1088WH
1013BKNM
1013CDNM
1013WH * For Non-IC applications only.
**Supplied with integral push-In wire connectors
Frame-In Kit
Reflector Trim
7
1104IC
23
6
1
5
4
1004ICN
(Integral Nail)
Top View
Overall Length
1004IC/N: 9"
13 3/4" MIN.
24” MAX.
Overall Width
1004IC/N: 5 3/4"
Overall Height
1004IC/N: 7 1/2"
Features
1. Housing: .032 (#20 ga.) aluminum. UL listed convertible IC/NON-IC. 2"
vertical adjustment in ceiling. Can be removed for access to junction box
and ceiling plenum. AirSeal®housing minimizes air leakage to less than 2
CFM at 1.57 PSF (or 75pa), which complies with Model Energy Code (Section
602.3.3) and Washington State Energy Code (Section 502.4) and reduces
heat loss and condensation in ceiling.
2. Mounting Frame: .048 (#18 ga.) galvanized steel. Locks into position along
length of mounting bars with locking spring and bendable slot. (3) slots 90°
apart simplify alignment.
3. Junction Box: 2"X 4" X 3 1/2" (22 cu. in.) .032 (#22 ga.) galvanized steel.
UL listed for maximum 6 (#12 ga.) 1004IC/N 90°C through branch circuit con-
ductors. Integral cable clamps permit attachment of non-metallic (#12 or #14
ga.) Romex®cable without tools or additional connectors.
4. Mounting Bars: .059 (#16 ga.) galvanized steel. Bars pivot for easy attach-
ment and wire-in below ceiling line. Bars extend to accommodate 16" to
24" O.C. joist spacing. The 1004IC features integral self-tapping philips
screws for secure attachment to wood or metal construction. The 1004ICN
features integral nails for secure attachment to wood. Both attach to T-bar
ceilings without the need of accessories.
5. Socket Housing: Impact extruded aluminum or galvanized steel. Attached
trim retaining spring secures trim to any height on housing wall.
6. Socket: Porcelain medium base: nickel plated screw shell. Pre-wired with
#18 ga. SF1 (300 VOLT 200° C) leads to junction box.
7. Thermal Protector: Meets NEC and UL requirements. Located inside
housing.
Options & Accessories
AirSeal®Kit: LAS56
NOTE: Use only if factory installed tape or knockouts are removed from vertical
adjustment slots in housing wall.
Labels
UL (Type IC/NON-IC Convertible; Suitable for Damp Locations)
Complies with Air Leakage Requirements stated in the Model Energy Code and
the Washington State Energy Code.
AirSeal®is a registered trademark of Lightolier.
Romex®is a registered trademark of General Cable Industries Inc.
1004IC
(Integral Screw)