LIGMAN NEON Series User manual

For Installation of NEON CLASSIC Continuous LED Solution IP67 (24VDC)
24VDC
M ITNO1230001067-CL-HB/16/12/19/REV.0
IP67
ALWAYS UNCOIL BEFORE USE
Actual product characteristics may vary. Ligman Lighting reserves the right to improve, modify or update the product designs without prior notice.
Please note drawings are an installation guide only. Each LED tape application may have variable factors. Cable size may need to be specified to limit the voltage drop throughout the circuit.
COLOUR NEON SERIES
WARM WHITE
3000K +/- 175K NEON 7
NATURAL WHITE
4000K +/- 275K NEON 7
2500 - 5000K
TUNEABLE WHITE NEON 8
RGB NEON 10
RGBW NEON 11
RGB DYNAMIC NEON 19
ELECTRICAL & OPTICAL DATA VARIANCE +/- 10%
SOLD BY THE METRE
IES FILES AVAILABLE
NEON CLASSIC │ELECTRICAL AND PHYSICAL INSTALLTION GUIDE
VARIANT CODE
ITNO1230001067-CL-HB
ITNO1240001067-CL-HB
ITNO12TUW01067-CL-HB
ITNO12RGB01067-CL-HB
ITNO15RGBW0567-CL-HB
ITNO12RGBC1067-CL-HB
RED
615–625mm
GREEN
520–530mm
BLUE
465–475mm
YELLOW
580mm
16.5
29
HORIZONTAL BENDING
MINIMUM
BEND RADIUS
60mm
NEON 9 ITNO12Y0001067-CL-HB
NEON 9 ITNO12B0001067-CL-HB
NEON 9 ITNO12G0001067-CL-HB
NEON 9 ITNO12R0001067-CL-HB

DO NOT TWIST THE LIGHT OR BEND
AGAINST THE LIGHT SURFACE
NEON CLASSIC CAN BE CURVED
AS SHOWN BELOW
LIGHT SURFACE
– (units are
clearly marked with dashed lines on the sides of the product)
–
“minimum bend radius” (60mm for Neon Classic)
BENDING PARAMETERS
60mm
M ITNO1230001067-CL-HB/16/12/19/REV.0

NEON CLASSIC| ELECTRICAL AND PHYSICAL INSTALLATIONGUIDE
– LED Neon must always be used in conjunction with a
– Check the polarity of the connector before inserting the front
connector and switching on the mains power.
– To minimise voltage drop and ensure consistent light output,
position the power supply near to the power feed end of the
LED Neon, and keep the line as short as possible
– Ensure your maximum run per power feed adheres to the
– Ensure to add 20% buffer when selecting a power supply
– Before making any cuts, installation, maintenance, or
connection, be sure the mains power is disconnected.
– If essential; cut and connect LED Neon correctly. Any
incorrect operation can cause damage.
– All connector joints must be connected correctly to
achieve connector IP rating.
WHITE / SINGLE COLOUR
WIRING DIAGRAMS
RGBW
RGB
POWER SUPPLY RGB CONTROL
green wire: “G” terminal (-)
blue wire: “B” terminal (-)
yellow wire: +
red wire: “R” terminal (-)
24V DC
TUNEABLE WHITE
POWER SUPPLY 2-CHANNEL
CONTROL
black wire: Cool White connection (-)
red wire: +
yellow wire: Warm White connection (-)
24V DC
POWER SUPPLY RGBW CONTROL
green wire: “G” terminal (-)
blue wire: “B” terminal (-)
white wire: “W” terminal (-)
yellow wire: +
red wire: “R” terminal (-)
24V DC
DYNAMIC RGB ‘CHASING’
POWER SUPPLY DIMMER
optional black wire: -
red wire: +
24V DC
DMX OPTION AVAILABLE
black wire: “GND”, Cathode (-) terminal
red wire: “VCC”, Anode (+) terminal
yellow wire: “Signal” terminal
POWER SUPPLY INDEPENDENT
SPI CONTROL
24V DC
M ITNO1230001067-CL-HB/16/12/19/REV.0

NEON CLASSIC| ELECTRICAL AND PHYSICAL INSTALLATIONGUIDE
PROFILE INSTALLATION REQUIREMENTS
– Ensure the supply cord is not subject to mechanical stress
–
–
– Avoid placing mechanical stress on the front connector cable
– Do not curl or bend the front connector cable with excessive force
–
–
PULL
M ITNO1230001067-CL-HB/16/12/19/REV.0

SNAP CONNECTIONS - IP67
TOP END FEED END CAP FLEXIBLE
CONNECTOR
WHITE
TUNEABLE
SINGLE COLOUR
RGB
RGB CHASING
RGBW ---
NEON CLASSIC | CONNECTIONS
SUITABLE FOR OUTDOOR APPLICATIONS
MUST BE FITTED CORRECTLY FOR IP67 RATING
FEED CONNECTORS SUPPLIED AS 1M CABLE STANDARD,
CHECK WITH BRIGHT LIGHT FOR ALTERNATE LENGTHS
FLEXIBLE CONNECTOR
L
300mm
END CAPTOP END FEED
M ITNO1230001067-CL-HB/16/12/19/REV.0

SLIMLINE INJECTION MOULDING CONNECTIONS - IP67
SIDE FEED BOTTOM
FEED
TOP END
FEED
MIDDLE FEED END CAP FLEXIBLE
CONNECTOR
T FEED
WHITE
TUNEABLE
SINGLE COLOUR
RGB
RGB CHASING -
RGBW -
NEON CLASSIC | CONNECTIONS
SIDE FEED
END CAP FLEXIBLE CONNECTOR
BOTTOM FEED
T-FEED
TOP END FEED MIDDLE FEED
300mm
REQUIRES FITTING AT FACTORY. LEAD
TIMES APPLY
SUITABLE FOR OUTDOOR APPLICATIONS
FEED CONNECTORS SUPPLIED AS 1M
CABLE STANDARD, CHECK WITH BRIGHT
LIGHT FOR ALTERNATE LENGTHS
300mm 300mm
1000mm
M ITNO1230001067-CL-HB/16/12/19/REV.0

CAPPED DUAL INJECTION MOULDING - IP68
SIDE FEED BOTTOM FEED TOP END FEED END CAP FLEXIBLE
CONNECTOR
WHITE
TUNEABLE
SINGLE COLOUR
RGB
RGB CHASING
RGBW
NEON CLASSIC | CONNECTIONS
REQUIRES FITTING AT FACTORY. LEAD TIMES APPLY
SUITABLE FOR OUTDOOR APPLICATIONS
FEED CONNECTORS SUPPLIED AS 1M CABLE
STANDARD, CHECK WITH BRIGHT LIGHT FOR
ALTERNATE LENGTHS
33mm
20mm17.5mm
42mm
2m m2 mm
Φ15m m
27mm
20mm
4mm
2mm
TOP END FEED
FLEXIBLE CONNECTOR
END CAP
Φ15m m
34mm
20mm18mm
22mm 3m m
2m m
50mm
10mm
2m m
33mm
35mm 20mm
15.5mm
4mm
BOTTOM FEEDSIDE FEED
15.5mm
20mm
35mm20mm
2m m 2m m
35mm
42mm
Φ15m m
27mm
4mm
300mm
M ITNO1230001067-CL-HB/16/12/19/REV.0

NEON CLASSIC| MOUNTING ACCESSORIES
ACCESSORY L1 L2 HOLE
DIMENSIONS
HOLE
NUMBER
SELF-LOCKING ALUMINIUM PROFILE 2M 100mm 200mm Ø3.5mm 10
SELF-LOCKING ALUMINIUM V2 MOUNTING CLIP 35MM 5mm 25mm Ø3.5mm 2
PLASTIC PROFILE 2M 100mm 200mm Ø3.5mm 10
PLASTIC PROFILE 1M 100mm 200mm Ø3.5mm 5
SELF-LOCKING ALUMINIUM
V2 MOUNTING CLIP
SELF-LOCKING ALUMINIUM
PROFILE 2M
PLASTIC PROFILE
L1 L2
14
24
16.2
25.6
16.8
23.7
M ITNO1230001067-CL-HB/16/12/19/REV.0