Lilin IPD2322ESX User manual

Instr uction Manual
66-IPD2322CSE
IPD2322ESX / LD2322EX
MERIT LILIN ENT. CO., LTD
http://www.meritlilin.com
D/N 1080P HD Vari-Focal Dome IP Camera

IMPORTANT SAFEGUARDS
GRAPHIC SYMBOL EXPLANATION
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's enclosure
that may be of sufficient magnitude to constitute a risk of electric
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
shock to persons.
accompanying the unit.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION：
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS

IPD2322ESX & LD2322EX series is an 2 megapixel Day&Night
1080P HD Vari-Focal Dome IP Camera, built-in H.264 AVC
(Advanced Video Coding) video compression. H.264 AVC video
compression engine supports high definition video quality,
1080P(1920x1080) resolution, bandwidth efficiency with PPPoE
and DDNS.
Also it provides higher bit rate of internet and diverse alarm
functions such as movement video detection e-mail or FTP.
Moreover, IPD2322ESX & LD2322EX series can do remote
surveillance with iPad, iPhone or Android cell phone. The
software R&D engineer can use HTTP protocol (HTTPAPI) or
ONVIF protocol to develop related software, and integrate them
with existing application software system.
IPD2322ESX & LD2322EX series is ideal solution for remote
video monitoring via internet.
Executive Summary

1
Unit: mm
2
3
4
150.0
6
80.0
5
PART DESCRIPTION & DIMENSION
134.0
7
8
9
10 11 12 14 1513
16
17
18

COM.GND
N.O.DIN
5 4 3 2 1
+5V
1Cylinder (Ceiling Mount)
Top Cover
Inner Cover
Dome Cover
Lens
Slide Cover
Fixed Plate (Ceiling Mount)
Bottom Chassis
Lock Plate
RJ-45 Network Connector
Audio Input 3.5mm Phone Jack
Audio Output 3.5mm Phone Jack
DC12V Power Input Jack
Live Video Output RCA Jack
Plug the video input of monitor to the RCA jack and adjust focus and zoom.
Alarm In/Out Terminal
Network Indicator LEDs
Green(LINK): Network cable connected, this LED lit.
Orange(ACT): Data communications, this LED flashes.
Reset Button
To restore the server to factory default setting.
Micro SD Card Slot
This network camera is compliant with micro SD/SDHC card.
2
3
4
5
6
7
8
10
9
11
12
13
14
15
16
17
18

INSTALLATION
Installation Structural Drawing
Embedded Mounting Attached Mounting

FIG.3 FIG.4
FIG.1 FIG.2
Embedded Mounting (False Ceiling)
1. Please use the screw driver to untighten the 3 screws on the top cover(FIG.1), and to
untighten the 3 screws on the cylinder(FIG.2).
2. Use a hole site diagram to cut the circle 108mm(FIG.3 & FIG.4).
3. Plug and fix the power cable to the jack and plug the network cable to RJ-45 connector
of the camera (FIG.5).
Ø 108
DRILL HOLE
DRILL HOLE
DRILL HOLE
FIG.5

PAN
TILT
FIG.8 FIG.9
FIG.6 FIG.7
4. Put the provided screw(M3.0x25, wooden screw) through the holes marked as “a”, and
fix the bottom chassis in the desired area (FIG.6 & FIG.7)
a
a
a
5. Take down the inner cover from the camera module (FIG.8), and then adjust the direction
of the lens through the adjustable Pan/Tilt bracket and rotatable round bracket for
Azimuth (FIG.9).
Press inward
and pull down.
AZIMUTH
FOC US
FIG.10
6. Adjust the lens on focus and zoom to form the optimal video image after that tighten the
screws (FIG.10).
ZOO M

FIG.13 FIG.14
FIG.11 FIG.12
7. Put on the inner cover (FIG.11). Replace the top cover and tighten the screws (FIG.12).
Attached Mounting (Fixed Ceiling)
1. Please use the screw driver to untighten the 3 screws on the top cover(FIG.13). Push the
lock plate of bottom chassis down for unlocking(FIG.14).
Push the lock
plate down
FIG.15 FIG.16
2. Put the provided screw(M3.0x25, wooden screw) through the holes marked as “a”, and
fix the fixed plate in in the desired area (FIG.15 & FIG.16).
a
a
Ø
CABLE HOLE
a
47mm

FIG.17
Push the lock
plate up
3. Put the camera module into fixed plate, and push the lock plate up for locking(FIG.17).
FIG.19 FIG.20
FIG.18
4. Plug and fix the power cable to the jack and plug the network cable to RJ-45 connector
of the camera (FIG.18).
5. Take down the inner cover from the camera module (FIG.19), and then adjust the
direction of the lens through the adjustable Pan/Tilt bracket and rotatable round bracket
for Azimuth (FIG.20).
Press inward
and pull down.
PAN
TILT AZIMUTH