Linak TECHLINE LA25 Instruction manual

Actuator LA25
Endstop signals and relative positioning - Single hall
Connection diagram
LINAK.COM/TECHLINE

FOR MOUNTING INSTRUCTIONS AND GUIDANCE IN USAGE, PLEASE SEE THE RELEVANT USER’S MANUALS
Copyright © LINAK 2019.04 . MA-M9-02-590-A .LINAK A/S reserves the right to make technical alterations
Connection diagram
9
2019 © LINAK A/S
Endstop signals and relative positioning - Single hall
25XXXXXXXX0K0X0X=XXXXX10XXXXXX
*YELLOW/GREEN: Endstop signals out are NOT potential free (see specifications on next page)
Tip: If you wish to use the endstop signals, you will have to keep power on the brown, blue,
red and black wires, otherwise the signal will be lost.
BROWN
BLUE
YELLOW*
GREEN*
RED
VIOLET
BLACK
+
-

FOR MOUNTING INSTRUCTIONS AND GUIDANCE IN USAGE, PLEASE SEE THE RELEVANT USER’S MANUALS
Copyright © LINAK 2019.04 . MA-M9-02-590-A .LINAK A/S reserves the right to make technical alterations
I/O Specifications
9
2019 © LINAK A/S
Endstop signals and relative positioning - Single hall
Input/Output Specification Comments
Description The actuator can be equipped with Single hall that
gives a relative positioning feedback signal when the
actuator moves.
See connection diagram, figure above
Brown 12-24VDC (+/-)
12V ± 20%
24V ± 10%
Under normal conditions:
12V, max. 5A depending on load
24V, max. 2.5A depending on load
To extend actuator:
Connect Brown to positive
To retract actuator:
Connect Brown to negative
Blue To extend actuator:
Connect Blue to negative
To retract actuator:
Connect Blue to positive
Red Signal power supply (+) 12-24VDC Current consumption:
Max. 40mA, also when the
actuator is not running
Black Signal power supply GND (-)
Green Endstop signal out Output voltage min. VIN - 2V
Source current max. 100mA
NOT potential free
Yellow Endstop signal in
Violet Single Hall output (PNP)
Movement per single Hall pulse:
LA25030 Actuator = 0.25 mm per pulse
LA25060 Actuator = 0.5 mm per pulse
LA25090 Actuator = 0.75 mm per pulse
LA25120 Actuator = 1.0 mm per pulse
LA25200 Actuator = 1.7 mm per pulse
Depending on load the frequecy is 10-20 Hz
Pulse ON time is minimum 8ms. OFF time between two
ON pulses is minimum 8ms.
Overvoltage on the motor can result in shorter pulses.
Output voltage min. VIN - 2V
Max. current output: 12mA
Max. 680nF
N.B. For more precise
measurements, please contact
LINAK A/S.
Low frequency with a high load.
Higher frequency with no load.
Input: Single hall output:
White Not to be connected

FOR MOUNTING INSTRUCTIONS AND GUIDANCE IN USAGE, PLEASE SEE THE RELEVANT USER’S MANUALS
Copyright © LINAK 2019.04 . MA-M9-02-590-A .LINAK A/S reserves the right to make technical alterations
Terms of use
The user is responsible for determining the suitability of LINAK products for specific application. LINAK takes great care in providing
accurate and up-to-date information on its products.
However, due to continuous development in order to improve its products, LINAK products are subject to frequent modifications and
changes without prior notice.Therefore, LINAK cannot guarantee the correct and actual status of said information on its products.
While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the same reasons as mentioned above, guarantee the availability
of any particular product. Therefore, LINAK reserves the right to discontinue the sale of any product displayed on its website or listed
in its catalogues or other written material drawn up by LINAK.
All sales are subject to the Standard Terms of Sale and Delivery for LINAK. For a copy hereof, please contact LINAK.