Lincat Opus 800 OG8410-A001 User manual

IS722 ECN 4447 Page 1 of 8
Operating Instructions
(Supplementary Instructions to Synergy Grill Information Pack)
Opus 800 Gas Synergy Grills
OG8410-A001 & OG8411-A001
Please make a note of your product details for
future use:
Date Purchased: _________________________
Model Number: __________________________
Serial Number: __________________________
Dealer: ________________________________

IS722 ECN 4447 Page 2 of 8
CONTENTS
Important Information
2
Warnings and Precautions
3
Checklist of Enclosures
User Instructions
Servicing and Maintenance
Component Replacement
Spares
Accessories
Service Information and Guarantee
3
4
5
5
6
6
7
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and notices.
Ensure that these are understood at all times.
WARNING!
This symbol is used whenever there is a risk of personal injury.
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE:
This symbol is used to provide additional information, hints and tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE

IS722 ECN 4447 Page 3 of 8
NOTE
WARNINGS AND PRECAUTIONS
It is mandatory that all appliances are installed, commissioned and serviced by a
qualified and competent person as defined by the regulations in force in the country
of installation.
Failure to comply will invalidate the warranty.
WARNING!
This appliance must be installed by a competent installation engineer in accordance with
the installation instructions, and should conform to the following requirements:
Do not obstruct or block the appliance flue.
Installation must include sufficient ventilation to prevent the occurrence of unacceptable
concentrations of substances harmful to health in the room in which they are installed.
It is recommended that this appliance is sited under an extraction canopy for the removal of
combustion products
After operation, some parts of the appliance will remain hot for a period of time. Please take
care to avoid accidental burns.
CAUTION!
All equipment must be earthed to prevent shock.
Do not connect directly to any flue, ducting or mechanical extraction system.
Installation should allow for a sufficient flow of fresh air for gas combustion.
Parts which have been protected by the manufacturer or his agent must not be adjusted by
the installer or user.
CHECK LIST OF ENCLOSURES
Model
OG8410 & OG8411
Tick
Information Pack
1
Operating Instructions
manual
1
Scraper
1
Branding Grid Lifter
1
SERIAL NUMBER
Each appliance at Lincat has a unique identifying number found in the top right
hand corner of the data plate attached at the rear of the appliance. Please record
that number in the space provided should it be required for future reference.
Serial Number

IS722 ECN 4447 Page 4 of 8
RED NEON
(FAULT)
AMBER NEON
CONTROL KNOB
USER INSTRUCTION
APPLIANCE USE
This appliance is only for professional use and should only be used by qualified personnel.
Ensure that the person responsible understands how to light, safely operate, clean and
shutdown the appliance and is made aware of the position and operation of the gas
isolating cock in the event of an emergency.
Ensure that all controls have free and easy movement, if not contact a qualified service
engineer.
This appliance is intended to be used for grilling of culinary preparations that can be cooked
or browned by means of radiant heat and MUST NOT be used for any other purpose.
Operators of the appliance must not leave combustible materials directly in the cooking
areas of the appliance when in use.
OPERATION OF THE APPLIANCE
 The appliance should not be left unattended when in use for any lengthy period of
time.
 Grilling of product should never be left unattended.
 Use hand and arm protection to avoid injuries from burns.
LIGHTING SEQUENCE
Please ensure that the gas isolation valve for the appliance is turned to the open position
and the unit is plugged into an electrical socket and switched on before attempting to light.
Turn the control knob clockwise 90° to the stylized flame (the amber neon will glow and
the ignition sequence will start) and the burner will ignite.
The unit will have three attempts to light the burner, if it is not successful it will go into
lockout and the red (fault) neon will glow. At this stage turn the power off to the appliance
and retry.
SHUT DOWN
To shut down the appliance rotate all control knobs anti-clockwise to the OFF position. The
gas supply stopcock or bottle valve should now be closed.

IS722 ECN 4447 Page 5 of 8
A
B
B
B
B
B
C
D
D
D
SERVICING AND MAINTENANCE
All servicing, maintenance and component replacement on this appliance should be
carried out by one of our recommended service engineers.
SERVICE ACCESS
To access and service the components
FACIA PANEL REMOVAL
Remove facia fixing screws B.
Remove facia A.
BACK PANEL REMOVAL
Remove back panel fixing screws D.
Remove back panel C.
Neon’s
Remove the facia panel A (see above).
Pull off the cables (noting their position).
Undo retaining nut and remove from facia.
Fit the new neon and re-assemble in the reverse order.
Switch
Remove the facia panel A (see above).
Remove control knob.
Pull off the cables (noting their position).
Remove the two fixing screws and remove switch.
Fit the new switch and re-assemble in the reverse order.
COMPONENT REPLACEMENT

IS722 ECN 4447 Page 6 of 8
Part Number
Part Description
OG8410
OG8411
KN518
Control Knob
1
2
KN02
Control Knob Clip
1
2
LE38
Leg
4
4
NE47
Amber Neon
1
2
NE49
Red Neon
1
2
SW101
Switch
1
2
Part Number
Description
Used on
OA8991
Stand on Legs –600mm
OG8410
OA8991/C
Stand on Castors –600mm
OG8410
OA8992
Stand on Legs –900mm
OG8411
OA8992/8C
Stand on Castors –900mm
OG8411
SPARE PARTS LIST
ACCESSORIES

IS722 ECN 4447 Page 7 of 8
For help with the installation, maintenance and use of your Lincat equipment, please
contact our service department:
UK: 01522 875520
For non-UK customers, please contact your local Lincat dealer.
All service work, other than routine cleaning MUST be carried out by qualified
personnel and a record kept of any remedial actions taken and at least cover the
requirements of the service schedule of this document. We cannot accept
responsibility for work carried out by other persons.
To ensure your service enquiry is handled as efficiently as possible, please
tell us:
Brief details of the problem
Product code
All available on serial plate
Type number
Serial
number
Lincat reserve the right to carry out any work under warranty, given reasonable
access to the appliance, during normal working hours, Monday to Friday, 08:30
to 17:00.
DECLARATION
All Lincat products capable of burning gaseous fuels, satisfy the requirements of
the Gas Appliance Regulations 2016/426.
GUARANTEE
This unit carries a comprehensive UK mainland warranty. The guarantee is in
addition to, and does not diminish your statutory or legal rights. Contact Lincat
for terms and conditions
The guarantee does not cover:
Accidental damage, missuse or use not in accordance with the
manufacturer’s instructions
Consumable items (such as filters, glass, bulbs, slot toaster elements and
door seals.)
Damage due to incorrect installation, modification, unauthorised service
work or damage due to scale, food debris build-up, etc.
The manufacturer disclaims any liability for incidental, or consequential damages.
Attendance is based on reasonable access to the appliance to allow the
authorised personnel to carry out the warranty work.
Service calls to equipment under warranty will be carried out in accordance with
the conditions of sale. Unless otherwise specified, a maximum of 15 minutes of
administrative time, not spent directly carrying out servicing work, is provided for
within the warranty. Any requirement for staff attending the call to spend greater
time than 15 minutes due to administrative requirements, such as on health and
safety risk assessments, will be chargeable at the prevailing rate.
SERVICE INFORMATION

IS722 ECN 4447 Page 8 of 8
For Information