Lincat Phoenix Salamander PHEAS01 Owner's manual

IS 712 ECN 4291 Page 1 of 8
Installation, Operating and Servicing
Instructions
PHOENIX Salamander
PHEAS01
Please make a note of your product details for
future use:
Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________

IS 712 ECN 4291 Page 2 of 8
CONTENTS
Important Information
2
Warnings and Precautions
3
Technical Data
3
Checklist of Enclosures
3
Installation and Commissioning
4-5
Operating Instructions
6
Cleaning
7
Servicing, Maintenance and Component Replacement
7
Fault Finding
7
Spare Parts List
7
Accessories
7
Service Information and Guarantee
8
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and notices.
Ensure that these are understood at all times.
WARNING!
This symbol is used whenever there is a risk of personal injury.
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE:
This symbol is used to provide additional information, hints and tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE

IS 712 ECN 4291 Page 3 of 8
WARNINGS AND PRECAUTIONS
This appliance must be installed, commissioned and serviced by a qualified person
in accordance with national and local regulations in force in the country of
installation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person.
Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
During operation parts may become hot - avoid accidental contact.
Disconnect this appliance before servicing, maintenance or cleaning.
TECHNICAL DATA
Height (mm)
544
Width (mm)
600
Depth (mm)
555
Weight (kg)
59
Cooking area w x d (mm)
525 x 335
Number of individually controlled heat zones
3
Heat input per element (kW)
1.5
Total heat input (kW)
4.5
Electricity supply 1N~+e 230V 50-60Hz
Current Rating (Amps)
19.6
Electricity supply 3N~+e 400V 50-60Hz
Current Rating (Amps)
L1 –6.5
L2 –6.5
L3 –6.5
CHECK LIST OF ENCLOSURES
Warranty card
Instructions manual
Collection tray
Chrome plated grilling rack
Heat shield

IS 712 ECN 4291 Page 4 of 8
INSTALLATION AND COMMISSIONING
This product is heavy; prior to installation a handling assessment should be made.
This appliance must be earthed. An equipotential bonding terminal is provided to
allow cross bonding with other equipment.
Means of isolation with at least 3mm contact separation in all poles must be
incorporated into the fixed wiring of this appliance.
The fixed wiring insulation must be protected by insulated sleeving having a
temperature rating of at least 60 Deg C.
Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary
polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57).
This appliance may be counter or wall mounted. For either installation, remove and
discard the 2 transportation screws (A) from rear panel (Fig 2).
Install this appliance on a level surface ensuring all vents are unobstructed. Any
partitions, walls or furniture must be of non-combustible material (see Fig 2).
Minimum distances A 300mm B 500mm.
Do not install above any heat source the unit vents from the underside and this
could cause damage to the unit.
Warning: During installation do not place on surfaces or near walls, partitions or
kitchen furniture and a like –unless they are made of non-combustible material or
clad with non-combustible heating-insulating material, and pay attention to fire
prevention regulations.
Electrical connection
The electrical supply cable enters the unit through a cable gland in the rear panel
with access via a removable side panel (see Fig 1).
Connection of the electrical supply cable is to a terminal block behind the side
panel. Open the protective cover on the terminal housing where indicated using a
flat bladed screwdriver. Fit a suitable cable into the strain relief and then to the
terminal block.
Fig 1

IS 712 ECN 4291 Page 5 of 8
Fig 2

IS 712 ECN 4291 Page 6 of 8
OPERATING INSTRUCTIONS
Control panel
E B C
A D
Fig 2
A Timer 0-15mins
B Off –Off position
CLeft heating element ON
D Left and centre elements ON
E All three heating elements ON
Only qualified or trained personnel should use this appliance.
This appliance has 3 cooking modes switching between modes during the
cook time is possible.
Switching on
After selecting the desired cook area turn the timer to start the heating cycle. Adjust
the hood to the desired height.
Note: At cycle end the timer bell will sound and heating elements will turn off.
Note: The unit should not be used without the collection try and grill rack fitted.
Shutting down
Turn the control knob to the ‘Off’ position and switch off at the isolating socket.
Be aware that the appliance will remain hot for some time.

IS 712 ECN 4291 Page 7 of 8
CLEANING
Your Lincat product has a manufacturer’s warranty. This requires you to maintain
and care for your product and follow maintenance instructions. If you fail to maintain
your unit or damage components Lincat may charge you for a warranty repair.
Please check the website for terms and conditions.
Do not use a water jet or steam cleaner, and do not immerse this appliance.
Clean all panels with warm water and mild detergent, do not use abrasive materials
or cleaners containing chlorine. Dry with a soft cloth.
SERVICING, MAINTENANCE AND
COMPONENT REPLACEMENT
All servicing, maintenance and component replacement on this appliance should be
carried out by one of our recommended service engineers.
Please refer to the Service Help Desk number on the final page of this manual.
Part Number
Description
EL309
Element
CO215
Contactor
GL658
Glass
KN251
Control knob
SS11
Straps
SW105
Multi-Function Switch
TI57
15min timer
WI18
Wire tray grid
Part Number
Description
PHA01
Wall bracket
FAULT FINDING
SPARE PARTS LIST
ACCESSORIES

IS 712 ECN 4291 Page 8 of 8
For help with the installation, maintenance and use of your Lincat equipment,
please contact our service department:
UK: 01522 875520
For non-UK customers, please contact your local Lincat dealer
All service work, other than routine cleaning should be carried out by one of our
authorised service agents. We cannot accept responsibility for work carried out by
other persons.
To ensure your service enquiry is handled as efficiently as possible, please tell us:
Brief details of the problem
Product code
All available on serial plate
Type number
Serial number
Lincat reserve the right to carry out any work under warranty, given reasonable
access to the appliance, during normal working hours, Monday to Friday, 08:30 to
17:00.
GUARANTEE
This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is
in addition to, and does not diminish your statutory or legal rights.
The guarantee does not cover:
Accidental damage, misuse or use not in accordance with the manufacturer’s
instructions
Consumable items (such as filters, glass, bulbs, slot toaster elements and door
seals.)
Damage due to incorrect installation, modification, unauthorised service work or
damage due to scale, food debris build-up, etc.
The manufacturer disclaims any liability for incidental, or consequential damages.
Attendance is based on reasonable access to the appliance to allow the authorised
technician to carry out the warranty work.
SERVICE INFORMATION