Linka LASSO User manual

LINKA LASSO Owner’s Manual
Table of Contents
Before Getting Started 3
1. Important Safety and Product Information 3
c. Battery Warnings 3
d. Declaration of Conformity 3
e. FCC Compliance 3
f. Industry Canada Compliance 4
2. Limited Warranty 5
a. Warranty Policy 5
1. Welcome 6
a. Introducing the LINKA LASSO Smart Chain Lock 6
1. Setting up your LASSO 7
LED Legend 8
2. Pairing your device 9
c. Logging in 9
i. Sign up 9
ii. Sign in 9
d. Enable Bluetooth on your phone 9
e. Power up your LASSO 9
f. Select your device from list 9
g. Setup your phone-less access code 10
2. Securing items with LASSO 10
3. Unlocking your device 11
i. Unlock by button on LINKA 11
4. Locking your device 12
5. Access your device via Phone-less Access Code 12
6. Settings (In App) 12
d. Phone-less Access Code 13
f. Edit Lock Name 13
g. Audible Alarm 13
7. Charging Your LINKA device 13
8. Sharing your LINKA device 14
a. Sharing your LINKA is very easy and can be done remotely. 14
b. Sharing when device is locked or unlocked 14
1. Troubleshooting & Support 18
a. Rebooting the device 18
b. Factory Reset 18
Page - 1

Before Getting Started
When using your LINKA LASSO device for the first time, you should complete these tasks to set
up the device and get familiar with the basic features.
1.Important Safety and Product Information
a. Please read this owner’s guide
b. Please take the time to follow the instructions in the owner’s guide carefully. It will
help you get the most out of the features your new LINKA product has to offer.
Save the owner’s guide for future reference.
c. Battery Warnings
i. If these guidelines are not followed, the internal lithium-ion battery may
experience a shortened lifespan, a risk of damage to operability of the
device, fire, chemical burn, electrolyte leak, and/or injury.
1. Do not puncture or incinerate the device or battery.
2. When storing the device for an extended time, store within the
following temperature range: from 32 F to 77 F (from 0 C to 25 C)
3. Do not operate the device outside of -4 F to 131 F (from -20 C to
55 C).
4. Contact your local waste disposal department to dispose of the
device/battery in accordance with applicable local laws and
regulations.
5. Do not charge device below temperature 32F (0 C)
ii. Non-User replaceable Battery Warning: Do not remove or attempt to
remove the non-user-replaceable battery.
d. Declaration of Conformity
i. Hereby, LINKA declares that this product is in compliance with the
essential requirements and other relevant provisions. To view the full
Declaration of Conformity, see the LINKA website:
www.linkalock.com/compliance.
e. FCC Compliance
1. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
a. (1) This device may not cause harmful interference, and
b. (2) This device must accept any interference received,
including interference that may cause undesired
operation.
Page - 3

ii. Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
iii. NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
iv. FCC Radiation Exposure Statement:
1. This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance 20cm between the
radiator & your body.
f. Industry Canada Compliance
i. English:
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device."
ii. French:
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes :
Page - 4

(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, meme si le brouillage est susceptible d'en
compromettre le fonctionnement."
iii. Le présent appareil est conforme Après examen de ce matériel aux
conformité ou aux limites d’intensité de champ RF, les utilisateurs
peuvent sur l’exposition aux radiofréquences et compliance
d’acquérir les informations correspondantes. La distance minimale
du corps à utiliser le dispositif est de 20cm.
iv. The device is in compliance with RF exposure guidelines, users can
obtain Canadian information on RF exposure and compliance. The
minimum distance from the body to use the device is 20cm.
2.Limited Warranty
a. Warranty Policy
i. LINKA warrants to the original end user customer or purchaser of this
Product (“You”) that the product is free from defects in material and
workmanship, subject to the conditions stated herein, for the shorter of:
(1) a period from the date of purchase of the product in its original sealed
packaging until the expiration date of the Limited Warranty as specified in
the Warranty Policy. (Refer to the entire Warranty Policy for details.) (2) If
no proof of the date of purchase is provided, the warranty period will be
considered to have started three (3) months after the date that the
product was manufactured.).
ii. Within this period, LINKA will, at its sole discretion, repair or replace any
components that fail in normal use. Such repairs or replacement will be
made at no charge to the customer for parts or labor, provided that the
customer shall be responsible for any transportation cost. This warranty
does not apply to:
1. Cosmetic damage, such as scratches, nicks and dents;
2. Consumable parts, such as batteries, unless product damage has
occurred due to a defect in materials or workmanship;
3. Damage caused by accident, abuse, misuse, water, flood, fire, or
other acts of nature or external causes;
4. Damage caused by service performed by anyone who is not an
authorized service provider of LINKA;
5. Damage to a product that as been modified or altered without the
written permission of LINKA;
Page - 5

6. Damage to a product that has been connected to power and/or
data cables that are not supplied by LINKA. In addition, LINKA
reserves the right to refuse warranty claims against products or
services that are obtained and/or used in contravention of the laws
of any country.
1.Welcome
a. Introducing the LINKA LASSO Smart Chain Lock
i. Thank you for purchasing your LASSO Smart Chain Lock from LINKA.
Our innovative technology allows you to secure your bike or other
valuables with no physical keys and an increased peace of mind.
LASSO button layout:
1. LED Indicator dome
2. button
3. Pogo charge point
Page - 6

1.Setting up your LASSO
Before turning on your device for the first time, charge your LASSO overnight using the included
pogo charging cable. The LED indicator will turn red while being charged and will change solid
green when fully charged.
While your LASSO is charging be sure to download the LINKA app from your preferred app
store.
a. Once charged and unplugged, Tap
b. LED dome will begin blinking blue identifying that your device is now in
discoverable mode. You will also hear an audible start up tone.
c. Open up your downloaded LINKA app and continue the pairing process there.
NOTE: LED dome will blink blue (stay in discoverable mode) for 90 seconds before
turning your device off to conserve battery power.
Page - 7

LED Legend
Color
Pattern
Mode
Description
What to do?
Blue
Pulsing
Discoverable
When your device is turned on, the LED
dome will blink blue for 90 seconds in
search of a phone to pair with.
1. Pair a new device
2. Be in range with a
previously connected
device
Green
Blinking
Unlocked
Paired and connected, when unlocked
your LASSO blinks green 3 times.
1. Hold the LASSO button for
1 second while paired with
Smart Motion Key or click
unlock in the app.
Red
Blinking
Locked
Locking, after joining both ends of the
lock your LED will blink red 3 times.
Allow your device to lock
Red/Blue
Blinking
Stall unlocking
If there is any interference while locking
you will hear a tone and see the LED
flash red/blue back and forth.
Ensure there is no interference when
locking and attempt to re-lock
Purple
Solid
Phoneless Access
Code Entry
When your phone is not present, utilize
the personalized phoneless access
code to access your LINKA device.
After holding the button for 6
seconds, and seeing the LED purple
enter your 4-digit access code
Red
Solid
Charging
Once your battery gets low, plug in the
pogo charge cable into a computer or a
usb-plug charger
Allow your device to charge
Green
Solid
Charged
Your battery is fully charged and ready
for more months of peace of mind and
riding
Unplug your device from the
micro-usb charge connector and get
back to riding your bike!
Purple/Gr
een
Alternating
Firmware Update
We’re learning from your feedback and
constantly looking to improve LINKA
and your experience
Allow your device to go through the
update process. LED will be purple
during update and turn green when
update is successful.
White
Blink
Button Press
When the LASSO power button is
pressed
LED light flashes white to confirm
button has been pressed
Green/Wh
ite
Blinking
Alarm Turns ON
Plays when LASSO has been locked
and within 30 seconds the power button
is pressed twice in quick unison (span
under 3 sec)
Your LASSO alarm has been
activated
Red
Strobe
Alarm Turns OFF
After Alarm has been activated for
30 seconds and LASSO senses
motion, alarm goes off for 2 min
Your LASSO alarm has been
deactivated
Blue
Blinking
Successful Bluetooth
pairing
When a new bluetooth pairing is
added to LASSO memory chip
(either phone or Smart Motion Key)
Once pairing is successful in the
LINKA app your LED light will blink 3
times in blue.
Page - 8

2.Pairing your device
a. Download the LINKA App through Google Play or the Apple Store:
b. Click LINKA icon to launch app once downloaded
c. Logging in
i. Sign up
1. Enter your Email
2. Click Create Account
3. You will receive an email with a confirmation code that will serve
as your one-time password.
4. Your app will remain logged in but if for some reason you are
logged out you can always log back in by entering the same email
address you used to sign up and we will email you a new one-time
password.
ii. Sign in
1. If you already have a LINKA account, enter Email and Password
2. Click Sign In.
d. Enable Bluetooth on your phone
i. If you don’t have bluetooth enabled on your phone, the LINKA app will
introduce a prompt to Enable.
e. Power up your LASSO
i. To enter discovery mode, Tap the button.
ii. LED dome will begin blinking blue identifying that your device is now in
discoverable mode. You will also hear an audible start up tone.
f. Select your device from list
i. Tap on “+” symbol in the app and select the LASSO Device.
Page - 9

g. Setup your phone-less access code
i. It is required that you enter and store a 4-digit phone-less access code
before continuing further. This is to ensure you don’t get locked out if you
don’t have your phone.
ii. Enter your 4-digit access code
1. For added security, Codes “1111” up to “9999” and “1234” are not
allowed.
iii. Re-enter your 4-digit access code and press Save
NOTE: All bluetooth connected settings, actions, alerts, etc. will function and appear only
when Bluetooth is enabled on your phone.
2. Securing items with LASSO
a. For the highest level of security for your bicycle we recommend threading your
LASSO through your bicycles frame.
b. When securing your motorcycle we recommend threading LASSO through your
bike’s rear rim.
Page - 10

c. Your LASSO can also be used to secure any other objects you would usually
secure with a lock and chain, such as a garage gate, barn door or kayak.
3.Unlocking your device
a. Once your device is paired, you will be able to unlock your LASSO device.
b. There are 3 ways to unlock your device. Unlock in App, Unlock by button on
LASSO while lock is paired with either app or optional SmartMotion Key, or
unlocking with your Phoneless Access Code (PAC)..
i. Unlock by button on LINKA
1. Single-press and hold for 1 second the button on LASSO and
manually spread both parts of the lock apart.
Page - 11

4.Locking your device
a. Once your device is paired, you will only be able to lock your device automatically
by manually joining both ends of the lock together and not through the LINKA
App.
b. The LINKA app will show you the status of your device and whether or not it is
locked or unlocked.
c. If there is an obstruction while locking, LASSO will automatically unlock.
i. You will receive an alert on your phone to re-lock your device and will
hear an audible “lock jam” tone.
ii. Ensure there are no obstructions and re-attempt to lock the device.
iii. Once Locked, you will hear a lock tone.
5.Access your device via Phone-less Access
Code
a. In some cases, your phone battery may be completely drained or your phone is
lost or forgotten. Phone-less Access Code Feature allows you to unlock LASSO
to access your bike or other valuables and get to your destination without any
delays or worries.
b. Press and hold down the button on LINKA until the LED dome turns solid
Purple (6 seconds).
c. Press the the number of times of your 1st digit then release until you hear an
audible beep sound. For example if the first digit of your code is “2” you will need
to press the button twice, then pause for 1 second before you enter the next digit
in your code.
d. Repeat the previous step until all 4 digits are entered. Your device will
automatically unlock after successfully entering all 4 digits.
e. If the code is entered incorrectly, you will hear an audible “unsuccessful” tone.
You must attempt steps b.-d. Again.
6.Settings (In App)
a. The Settings page allows you to customize specific features on your device.
b. To access this page, your device must be paired and connected.
c. To access/change your device Settings. Open your LINKA app and on your
LASSO homepage select the bottom tray right hand icon with the picture of the
cog wheel.
Page - 12

d. Phone-less Access Code
e. During your LASSO’s setup you will be prompted to create a phoneless access
code. This code is useful if you need to unlock your LASSO but do not have a
phone or SmartMotion Key with you.
i. Enter your personal 4-digit access code
ii. Re-enter your personal 4-digit access code
iii. Click Save
iv. NOTE: Record or store this access code somewhere safe to access your
device your phone is not present.
f. Edit Lock Name
i. Editing your lock name makes it easier for you to recognize your device
for your convenience.
ii. Click The Pencil Icon next to your LASSO name on the LASSO home
screen.
iii. Enter your desired lock name
g. Audible Alarm
i. The Audible Alarm feature allows a siren to sound when the device is
being tampered with. In some cases you may not need this feature and
can turn the siren feature off.
ii. Tap the slide to toggle between ON and OFF.
7.Charging Your LINKA device
NOTICE: To prevent corrosion, thoroughly dry the pogo charging port and the
surrounding area before charging.
Your LASSO device is powered by a built-in lithium-ion battery that you can charge using
a standard wall outlet, a USB port on your computer or a portable battery pack.
NOTE: The device will not charge when outside the temperature range of 32° to 112°F
(0° to 45°C)
Page - 13

a. Plug the pogo small end of the USB cable into the pogo charging port.
b. Plug the USB end of the cable into your computer, wall outlet-connected AC
adaptor or portable battery pack.
c. The LED indicator will turn red while being charged and will change solid green
when fully charged.
8.Sharing your LINKA device
a. Sharing your LINKA is very easy and can be done remotely.
b. Sharing when device is locked or unlocked
i. Make sure your LASSO is on and paired with your smartphone
ii. Click on the bottom left icon in your LINKA app home tray. The icon with
two user heads on it.
iii. Enter the email address of the user you want to share access with.
iv. Click Invite and Done
v. NOTE: Users with shared access to a LINKA device (except admins) will
not be able to change any of the existing settings on the LINKA device.
c. Revoking Permissions
i. Make sure your LASSO is on and paired with your smartphone
Page - 14

ii. Click on the bottom left icon in your LINKA app home tray. The icon with
two user heads on it.
iii. Swipe left on the user email address you want to remove. You should see
a red trash can icon appear next to their email address.
iv. Click the trashcan icon and select Confirm. Done!
9. Accessories
a. LINKA SmartMotion Key
i. To start you must first pair your LINKA Smart Key with your LINKA app.
ii. In your LINKA app, select your LASSO Device
iii. Go to Device Settings and Select Add a Smart Key
iv. Use the “+” Symbol to start the pairing process, which will have you scan
the QR code on your SmartMotion Key and follow the prompts in the
application.
v. Once a SmartMotion Key has been paired with your LASSO Smart Chain
Lock, you will be able to unlock your LASSO without your phone or
access code, as long as the Smart Key is within range, usually 1-3
meters.
vi. Please note that Bluetooth must be enabled on your phone to be able to
pair a smart key.
LASSO SPEC SHEET:
LINKA LASSO
Series
8
10
10 Moto or 10XL
Model
LK-B220
LK-B221
LK-B222
Region
Global
Global
Global
Wired version
-
-
-
Rechargeable
version
Yes
Yes
Yes
Internal cell
Li-Ion cell 3.7V,
Li-Ion cell 3.7V, 1200mAh,
Li-Ion cell 3.7V, 1200mAh,
Page - 15

1200mAh, 4.44Wh
4.44Wh
4.44Wh
Interfaces
Wireless
interface
BT 5.0
BT 5.0
BT 5.0
External
Interface
-
-
-
Embedded
Modules
Bluetooth
Technology
Bluetooth Low Energy
5.0
Bluetooth Low Energy 5.0
Bluetooth Low Energy 5.0
Certifications
FCC/ISED/RED/MIC/
RCM/ANATEL/EAC/
IFETEL/SRRC/
RoHS/REACH/Prop65
FCC/ISED/RED/MIC/
RCM/ANATEL/EAC/
IFETEL/SRRC/
RoHS/REACH/Prop65
FCC/ISED/RED/MIC/
RCM/ANATEL/EAC/
IFETEL/SRRC/
RoHS/REACH/Prop65
Frequencies
2.360GHz-2.500GHz
2.360GHz-2.500GHz
2.360GHz-2.500GHz
Antenna Type
Embedded Ceramic Chip
Antenna
Embedded Ceramic Chip
Antenna
Embedded Ceramic Chip
Antenna
Antenna Gain
1dBi
1dBi
1dBi
Processor
1
1
1
Main processor
Bluetooth Processor
Bluetooth Processor
Bluetooth Processor
Secondary
Processor
-
-
-
Electrical
Features
Input Voltage
Pogo input 5VDC
Pogo input 5VDC
Pogo input 5VDC
Embedded
Li-Ion Battery
Charger IC -
IEC 62368-1
Certificate
Yes
Yes
Yes
Power
Consumption
Internal Cell Rail
Internal Cell Rail
Internal Cell Rail
Sleep
<80uA
<80uA
<80uA
Page - 16

Unlock/lock
mechanism
<100mA
<100mA
<100mA
Bluetooth
connected
8mA
8mA
8mA
Bluetooth
disconnected
2mA
2mA
2mA
Power
Consumption
External Voltage Rail
External Voltage Rail
External Voltage Rail
Charging
internal cell
<1000mA @ 5V
<1000mA @ 5V
<1000mA @ 5V
Environmental
Operating
temperature
-20°C to 65°C
(-4°F to 149°F)
-20°C to 65°C
(-4°F to 149°F)
-20°C to 65°C
(-4°F to 149°F)
Storage
temperature
20-25°C
20-25°C
20-25°C
Relative
humidity
60±25%
60±25%
60±25%
Mechanical
Enclosure
Material
Stainless Steel 304
Stainless Steel 304
Stainless Steel 304
Chain Material
20CrMnTi
20CrMnTi
20CrMnTi
Chain Link
Thickness
8mm
10mm
10mm
Length
100cm
100cm
140cm
Weight
1.8kg
2kg
2.2kg
Security Rating
8/10
10/10
10/10
IP Rate
67
67
67
Certifications
RF intentional
transmitter
RED/CE/FCC/IC
RED/CE/FCC/IC
RED/CE/FCC/IC
Security
Sold Secure - ART
(pending)
Sold Secure - ART (pending)
Sold Secure - ART
(pending)
Environmental
RoHS/REACH/ Prop 65
RoHS/REACH/ Prop 65
RoHS/REACH/ Prop 65
Page - 17

1.Troubleshooting & Support
a. Rebooting the device
i. If the device stops responding, you may need to reset it. This step will not
erase any of your data or settings.
ii. Hold down for 10 seconds while paired and connected or unlocked.
iii. The device reboots and turns back on.
b. Factory Reset
i. If the device is changing ownership or for any reason you’d like to restore
original factory settings.
ii. To Factory Reset: click on the App Icon on your phone >> Open Slide
Menu >> My LINKA >> Select desired LINKA from list >> Settings >>
Reset Factory Settings
iii. The main device owner will receive an e-mail to prompt the reset.
c. Updating Software
i. Your LINKA app will notify you when there are new software and firmware
updates available.
ii. Once your device is paired, the latest firmware stored in the App will
update your device wirelessly if there are firmware specific updates
available.
iii. Do not turn off your phone or change any settings on your device during
the update process
d. More Support
i. For more support and FAQ’s, check out our support page at
www.linkalock.com/pages/lasso-support
2.Software License Agreement
a. By using this device, you agree to be bound by the terms and conditions of the
following software license agreement. Please read this agreement carefully.
b. LINKA grants you a limited license to use the software embedded in this device
(the “Software”) in binary executable form in the normal operation of the product.
Title, owner rights, and intellectual property rights in and to the Software remain
in LINKA and/or its third party providers.
Page - 18

c. You acknowledge that the Software is the property of LINKA and/or its third party
providers and is protected under the United States of America copyright laws and
international copyright treaties. You further acknowledge that the structure,
organization, and code of the Software, for which source code is not provided,
are valuable trade secrets of LINKA and/or its third-party providers and that the
Software in source code form remains a valuable trade secret of LINKA and/or its
third-party providers. You agree not to decompile, disassemble, modify, reverse
assemble, reverse engineer, or reduce to human readable form the Software or
any part thereof or create any derivative works based on the Software. You agree
not to export or re-export the Software to any country in violation of the export
control laws of the United States of America or the export control laws of any
other applicable country.
Page - 19
Table of contents
Other Linka Lock manuals