Allegion Falcon Series User manual

BEFORE ATTEMPTING TO INSTALL LOCK, READ ALL
INSTRUCTIONS AND LAY PARTS OUT AS SHOWN IN
FIGURE 7A OR 7B
BORE 1" HOLE (25mm)
PARALLEL TO
SIDES OF DOOR
CENTER
FOR 1³⁄₄"
DOORS
(44mm)
CENTER
FOR 1³⁄₈"
DOORS
(43mm)
FOLD ALONG EDGE OF DOOR
1¹⁄₂"
HOLE
1"
HOLE
1¹⁄₈" (28mm) MIN.
BEYOND REQUIRED BACKSET
DISTANCE
FROM EDGE
OF DOOR
(BACKSET)
IMPORTANT
PLACE TEMPLATE
ON HIGH EDGE
OF DOOR BEVEL
BORE 1¹⁄₂" (38mm) HOLE AT CORRECT BACKSET
2³⁄₄"
(70mm)
5" (127mm)
2³⁄₈"
(60mm)
Marking Template for New Installations
1 Mark centers for latch
holes and side holes (follow
template instructions)
2 Drill 1¹⁄₂" dia. hole in
face and 1" dia. hole in
edge of door per template
instructions
3 Insert latch in edge
keeping its face parallel to
face of door. Mark outline of
latch face and remove latch
4 Chisel 5\32" (3.97mm)
deep or until latch face
is flush with door edge.
5Insert latch and secure
with two (2) No. 7 x ³⁄₄" wood
screws. Tighten screws.
EXTENDED
Install with
A on Top
002103-000-70
© Allegion 2014
Printed in U.S.A.
002103-000-70 Rev. 10/14-d

IMPORTANT: EXTEND DEADBOLT BEFORE PROCEEDING
6 TRIM ASSEMBLY
8. STRIKE INSTALLATION
STANDARD STRIKE
OPTIONAL STRIKE
Small rings (F) are used only on
1³⁄₈" thick doors
Install
keyed trims
as shown
(Key Notches Up)
Single Cylinder Screw ¹⁄₄" bolts (I) through plate* (H) into
housing (B) & tighten. Engage tailpiece (P) with thumbturn
(J). Fasten thumbturn (J) to plate (H) with short machine
screws (K)
NOTE Align plate with the large holes below the small holes
as shown
Double Cylinder Screw ¹⁄₄" bolts (J) through housing (H),
and ring (E) into housing (B) engaging tailpieces (P) with
the vertical slot in the deadbolt
Important: Check locking and unlocking of both sides
with door open before snapping covers (K) over bolts (J).
Place strike on
jamb, centering over
hole and parallel to
edge of frame. Mark
outline and remove
strike.
DChisel cutout ¹⁄₁₆"
deep for standard strike.
Chisel cutout ¹⁄₁₆" deep
for optional strike.
GInstall strike with
No. 7 x ³⁄₄" screws.
Tighten screws.
7A SINGLE CYLINDER
ASSEMBLY
Optional
Interchangeable Core
K
J
I
H
G
F
E
AC
D
P
B
R
M
N
7B DOUBLE CYLINDER
ASSEMBLY
Optional
Interchangeable Core
K
J
E
F
G
F
E
AC
D
P
B
L
C
D
H
L
DOOR
STOP
Screws (S)
(O) Screws
M
BBore 1" diameter hole
1¹⁄₈" deep centered
between the markings.
CAUTION: Deadbolt will
not function correctly if
hole is too shallow.
AMark the corners of the
deadbolt with crayon or
grease pencil. Retract
deadbolt and close door.
Throw dead bolt firmly
against jamb to transfer
markings.
FDrill 2 pilot holes (O) 3" deep to prevent splitting of jamb and
install 3" long screws (O) in large holes next to door jamb
ECenter strike (M) over hole with small holes (S) away
from door stop. Install 2 small screws (S).
Check locking function before installing longer screws.
C
S

4.250
3.125
Additional Notes: Revision History Revision Description:
D > Revised artwork
1. None A B C D E F
FAL 0790 6683
Material
50# oset or equivalent
Edited By Approved By EC Number Release Date
J. Ellis M. Roberts xxxxx 10/14
Notes
1. printed both sides
2. printed black
3. tolerance ± .13
4. printed in country may vary
5. barcode shows after folding
Title
Falcon Marking Template for New Installations
Creation Date
10-22-14
Number
002103-000-70
Revision
D
Created By
J. Ellis Activity
3899 Hancock Expwy
Security, CO 80911 © Allegion 2014Software: InDesign CS6
4.250
12.500
BEGINNING SHEET
FOLDED SHEET
FRONT
FRONT