LinMot PR02-70 Series User manual

NTI AG / LinMot Dok-Nr. 0185-0170-E_1V0_IG_Linear_Rotary_Motors_PR02-70
Installation Guide
Linear Rotary Motors
ENG
PR02-70

Installation Guide Linear Rotary Motors ENG
Page 2 / 41 PR02-70 NTI AG / LinMot
Content
1General information ................................................................................................................................. 4
1.1 Introduction........................................................................................................................................ 4
1.2 Explanation of symbols...................................................................................................................... 4
1.3Qualified personnel............................................................................................................................ 4
1.4 Liability............................................................................................................................................... 4
1.5 Copyright............................................................................................................................................ 4
2Safety instructions ................................................................................................................................... 5
3Intended Use............................................................................................................................................. 7
3.1 Designation Code PR02 Linear Rotary Motors ................................................................................. 7
3.2 PR02-70 Linear Rotary Motor............................................................................................................ 7
3.3 Internal Mechanical Stops ................................................................................................................. 8
3.4 Max. Speed........................................................................................................................................ 8
3.5 Option Load Compensation MagSpring®.......................................................................................... 8
3.6 Option Hollow Shaft........................................................................................................................... 8
3.7 Option Pusher (Pneumatic / Electric) ................................................................................................ 8
3.8 Option Torque Sensor ....................................................................................................................... 9
3.9 Option Force Sensor.......................................................................................................................... 9
3.10 Option Stainless Steel Front Flange (SSC)..................................................................................... 10
4Installation instructions......................................................................................................................... 11
4.1 Operating Conditions....................................................................................................................... 11
4.2 Assembly of the Linear Rotary Motor .............................................................................................. 11
4.3 Mounting the Load on the Shaft ...................................................................................................... 12
4.4 Material Data ................................................................................................................................... 12
4.4.1 Standard Design.......................................................................................................................... 12
4.4.2 Stainless Steel Front SSC ........................................................................................................... 12
5Connections............................................................................................................................................ 13
5.1 Electrical Connection....................................................................................................................... 13
5.1.1 Motor Cable ................................................................................................................................. 13
5.1.2 Wiring Linear Rotary Motor.......................................................................................................... 14
5.1.3 Overview of the Connectors ........................................................................................................ 15
5.1.4 Connector Wiring Linear Rotary Motor........................................................................................ 15
5.1.5 Connector Wiring Torque Measuring Shaft / Force Sensor ........................................................ 16
5.2 Connector Wiring Electric Pusher.................................................................................................... 17
5.3 Connection of Air ............................................................................................................................. 17
6Start-up.................................................................................................................................................... 18
6.1 Linear Motor and Rotary Motor........................................................................................................ 18
6.2 Default Values of the Coordinate System........................................................................................ 18
6.2.1 Angle of Rotation ......................................................................................................................... 18
6.2.2Position........................................................................................................................................ 18
6.3 Torque Measuring Shaft .................................................................................................................. 19
6.3.1 Torque Operating Direction ......................................................................................................... 19
6.4 Force Sensor ................................................................................................................................... 19

Installation Guide Linear Rotary Motors ENG
NTI AG / LinMot PR02-70 Page 3 / 41
6.4.1 Force Operating Direction............................................................................................................ 19
6.5 Magnetic Spring MagSpring®.......................................................................................................... 20
6.5.1 Force Direction............................................................................................................................. 20
6.6 Plug and Play Function for Linear Rotary Motors............................................................................ 20
6.7 Setting Motor Parameters................................................................................................................ 20
6.7.1 Selection of the Motor Data Files................................................................................................. 20
6.7.2 Application-specific Parameters .................................................................................................. 21
6.7.3 Inverting the Coordinate System ................................................................................................. 21
6.7.4 Selection of the Linear and Rotary Unit System.......................................................................... 23
6.7.5 Referencing the Linear Motor ...................................................................................................... 23
6.7.6 Referencing the Rotary Motor...................................................................................................... 24
6.8 Initial Setup of Torque Measuring Shafts and Force Sensors......................................................... 24
6.8.1 Software Package „Technology Function Force Control“............................................................ 24
6.8.2 Setting Parameters for Torque / Force Control ........................................................................... 24
6.8.3 Initial Test of a Torque Measuring Shaft / Force Sensor............................................................. 25
7Accessories ............................................................................................................................................ 27
7.1 Motor Cable ..................................................................................................................................... 27
7.2 Sensor Cable................................................................................................................................... 28
7.3 Mounting Flange.............................................................................................................................. 29
7.4 Shaft-Hub Clamping ........................................................................................................................ 30
7.4.1 Dimensions and Technical Data.................................................................................................. 30
7.4.2 Mounting...................................................................................................................................... 30
8Maintenance and Test Instructions ...................................................................................................... 31
8.1 Stator Checking ............................................................................................................................... 31
8.1.1 Linear Motor PS01-48x240F-HP-C.............................................................................................. 31
8.1.2 Rotary Motor Stator RS02-70x100-C .......................................................................................... 31
8.2 Maintenance .................................................................................................................................... 31
8.2.1 Preventive Inspection every 6'000h............................................................................................. 32
8.2.2 Inspection after each 12'000h...................................................................................................... 32
8.3 Calibration of Torque Measuring Shaft and Force Sensor.............................................................. 32
9Transport and Storage........................................................................................................................... 32
10 Dimensions......................................................................................................................................... 33
10.1 PR02-70x100(-SSC)-C_48x240F-HP-C-150((-L01)-MSxx-TSxx-FSxx) ......................................... 33
10.2 PR02-70x100(-SSC)-C_48x240F-HP-C-150-L05(-MSxx-TSxx-FSxx)............................................ 34
10.3 PR02-70x100(-SSC)-C_48x240F-HP-C-150-L15(-MSxx-TSxx-FSxx)............................................ 35
10.4 PR02-70x100(-SSC)-C_48x240F-HP-C-240((-L01)-MSxx-TSxx-FSxx) ......................................... 36
11 International Certificates................................................................................................................... 37
12 EU Declaration of Conformity CE-Marking ..................................................................................... 39
13 UK Declaration of Conformity UKCA-Marking................................................................................ 40

Installation Guide Linear Rotary Motors ENG
Page 4 / 41 PR02-70 NTI AG / LinMot
1 General information
1.1 Introduction
This manual includes instructions for the installation, maintenance, transport, and storage of linear rotary
motors. The document is intended for electricians, mechanics, service technicians, and warehouse staff.
Be sure to observe the general safety instructions as well as those in each chapter at all times.
Keep this manual accessible to the assigned staff.
1.2 Explanation of symbols
Triangular warning symbols warn against a danger.
Round command symbols tell what to do.
1.3 Qualified personnel
All work such as transport, installation, commissioning and service is only allowed to be carried out by
qualified personnel. Qualified personnel in the sense of the safety instructions in this documentation are
persons who are familiar with the transport, installation, assembly, commissioning and operation of the
product and who have the appropriate qualifications.
This manual must be read carefully before transport, installation, commissioning, service and all safety-
related information must be adhered to.
1.4 Liability
NTI AG (as manufacturer of LinMot linear motors and MagSpring products) excludes all liability for damages
and expenses caused by incorrect use of the products. This also applies to false applications, which are
caused by NTI AG's own data and notes, for example in the course of sales, support or application activities.
It is the sole responsibility of the user to check the information and information provided by NTI AG regarding
their safety-relevant correctness. In addition, the entire responsibility for safety-related product functionality
lies exclusively with the user.Product warranties are void if products are used with stators, sliders, servo
drives or cables not manufactured by NTI AG unless such use was specifically approved by NTI AG.
NTI AG’s warranty is limited to repair or replacement as stated in our standard warranty policy as described
in our "terms and conditions" previously supplied to the purchaser of our equipment (please request copy of
same if not otherwise available). Further reference is made to our general terms and conditions.
1.5 Copyright
This work is protected by copyright.
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or
mechanical, including photocopying, recording, microfilm, storing in an information retrieval system, not even
for training purposes, or translating, in whole or in part, without the prior written consent of NTI AG.
LinMot® is a registered trademark of NTI AG.

Installation Guide Linear Rotary Motors ENG
NTI AG / LinMot PR02-70 Page 5 / 41
2 Safety instructions
Pacemaker / Implanted heart defibrillator
Sliders could affect the functioning of pacemakers and implanted heart defibrillators. For the
duration of a strong approach to a magnetic field, these devices switch into test mode and
will not function properly.
•If you wear one of those devices keep a minimum distance of 300 mm (12ʺ) between
the pacemaker / defibrillator and the housing of the linear rotary motor.
•Inform others who wear these devices to comply with this minimum distance!
Caution - Risk of Electric Shock !
Before working, make sure that there are no high voltages.
Fast-moving machine parts
The sliders of LinMot linear motors are fast-moving machine parts. All necessary
precautions must be taken to prevent persons approaching the moving elements during
operation (provide covers, guards, etc.).
Automatic restart
The motors can start automatically under certain cricumstances!
If necessary, a corresponding warning symbol must be provided and protection against
entering the hazardous area or a suitable safe electronic disconnection must be provided!
Risk of injury due to a defect or fault
For areas where a defect or fault can result in substantial property damage or even serious
personal injury, additional external precautions must be taken or devices must be installed
to ensure safe operation even if a defect or fault occurs (eg. suitable safe electronic
disconnection, mechanical interlocks, barriers, etc.).
Magnetic field
Magnets integrated in the sliders produce a strong magnetic field. They could damage TVs,
laptops, computer hard drives, credit and ATM cards, data storage media, mechanical
watches, hearing aids, and speakers.
•Keep magnets away from devices and objects that could be damaged by strong
magnetic fields.
•For the above mentioned objects, keep a minimum distance as described in the
"Pacemaker / implanted defibrillator" section.
•For non-anti-magnetic watches, keep the double minimum distance.
Burn hazard
The shaft of LinMot linear rotary motors can reach temperatures of 80 °C, which may cause
burns upon contact.
Grounding
All metal parts that are exposed to contact during any user operation or servicing and likely
to become energized shall be reliably connected to the means for grounding.

Installation Guide Linear Rotary Motors ENG
Page 6 / 41 PR02-70 NTI AG / LinMot
Effects on people
According to the current level of knowledge, magnetic fields of permanent magnets do not
have a measurable positive or negative effect on people. It is unlikely that permanent
magnets constitute a health risk, but it cannot be ruled out entirely.
•For your own safety, avoid constant contact with magnets.
•Store large magnets at least one meter away from your body.
Temperature resistance
Keep motors away from unshielded flame or heat.
Temperature above 120°C will cause demagnetization.

Installation Guide Linear Rotary Motors ENG
NTI AG / LinMot PR02-70 Page 7 / 41
3 Intended Use
3.1 Designation Code PR02 Linear Rotary Motors
PR02-70x100 -C_48x240F-HP-C-150-Lxx_MSxx_TSxx_FSxx _xxx
Option mech. variant /
customized
Option force sensor
Option torque sensor
Option load compensation / MagSpring
Option hollow shaft (L01) / Pusher (L05 / L15)
Stroke range
Connector type (Linear motor)
Linear motor type
Connector type (Rotary motor)
Rotary motor type
Motor family
3.2 PR02-70 Linear Rotary Motor
LinMot linear rotary motors are direct electric drives for use in industrial and commercial installations. For
correct handling, observe the warnings listed in chap. 2.
The PR02 motor series is characterized by a slim design in which a linear and a rotary motor including
additional components are integrated in a common housing.OptionThis features a high-precision and
complex mechanical system. The optimization of the internal moving load mass, as well as the moment of
inertia, enables a dynamic movement of linear and rotating motion.
The PR02 linear rotary motor is designed for the simultaneous execution of linear and rotating movements.
This means that the rotary and linear movements can be executed simultaneously and completely
Linear Rotary
Shaft
Rotary
Motor
Torque Sensor
Pn. / El. Pusher
Motor Connector (2x)
Housing
MagSpring
Linear Motor
Sensor Connector
Pusher Connector

Installation Guide Linear Rotary Motors ENG
Page 8 / 41 PR02-70 NTI AG / LinMot
independently of each other. However, if the application permits, it is recommended to execute the rotary
movement with the linear rotary shaft retracted, if possible. The rotary and linear movements should also be
carried out one after the other. This reduces the bearing loads and achieves a longer service life of the linear
rotary shaft.
By combining linear and rotary motion, highly complex motion patterns, such as those required in sealing
and assembly applications, can be easily realized using LinMot linear rotary motors. In addition to the two
motors, further options such as an air feed-through, a magnetic spring "MagSpring", a torque and a force
sensor as well as a pusher (electric or pneumatic telescopic movement) can be integrated in the housing.
3.3 Internal Mechanical Stops
Do not drive into the internal mechanical stops!
It must be ensured that the linear motor does not move to the lower or upper internal stop
during operation, as otherwise the linear motor may be damaged! The internal stops may
only be used for homing purposes. The homing speed must not exceed the value of 0.01
m/s.
3.4 Max. Speed
The mechanically maximum permissible speed of 1000 rpm must not be exceeded.
3.5 Option Load Compensation MagSpring®
The MagSpring option is a passive load compensation based on a magnetic spring with constant force over
the functional stroke range that can be integrated into the module. MagSprings are available in various force
levels and can either push or pull the linear rotary shaft. The MagSpring option can be used to compensate
the load mass. With the correct design, the motor current and thus its power loss can be reduced, by using a
MagSpring. This makes higher cycle rates possible.
If the MagSpring is sized properly, it can move the linear rotary shaft including the load mass into a collision-
free zone in the event of current loss.
•Close to the stroke limit (idle state), the MagSpring has a reduced force to protect the
linear rotary motor from mechanical shocks in case of malfunction/control (self-
acceleration into mechanical stop).
•If the maximum defined stroke (see data sheet) is exceeded, the MagSpring function
can no longer be guaranteed.
3.6 Option Hollow Shaft
Linear rotary motors can optionally be equipped with a pneumatic connection. This allows pneumatic
compressed air or vacuum to be fed directly through the linear rotary shaft. This avoids the complex passage
of hoses around the linear rotary shaft. This option can be used, for example, to control pneumatic grippers
or to pick up parts with the help of vacuum. For more information, see chapter 5.2 « Connecting the air ».
•In the case of a vacuum application, it is recommended to use a unit with sufficient
power, as any air coupling points are known to produce minor losses.
•Hollow shafts are not intended for the passage of liquid media.
3.7 Option Pusher (Pneumatic / Electric)
The optional pneumatic pusher (L05), which is technically a double-acting pneumatic cylinder, can be used
as a second independent linear movement. In the initial position, the pusher protrudes 20 mm above the
stroke turning shaft and achieves a total stroke of 25 mm. It generates a force of 300 N at 6 bar and can be
used, for example, to eject gripped elements or for the mechanical actuation of grippers. In addition to the
pneumatic version, LinMot also offers an electrically operated pusher (L15). This achieves the same total
stroke (25 mm) as its pneumatic counterpart and generates a force of 225 N. The electric pusher consists of
a second, fully integrated servo linear motor and can therefore not only move to freely selectable positions,
but also be operated with limited force. Mechanical grippers could thus also be partially opened or gripped
elements could be sensitively grasped with reduced force.

Installation Guide Linear Rotary Motors ENG
NTI AG / LinMot PR02-70 Page 9 / 41
3.8 Option Torque Sensor
The optional, integrated torque sensor enables closed-loop torque control with target torque specification.
The measurement signal is also available to the user for the cyclical recording / evaluation of sensitive
process data (e.g. tightening torque). This makes it easy to implement high-precision, reproducible and
recordable closing & assembly processes in accordance with Industry 4.0 requirements.
Torque sensors are based on the measuring principle of strain gauges and transmit the measuring signal
and the supply voltage without contact. This enables low-wear and maintenance-free continuous operation.
With this option, a suitable, galvanically isolated measuring amplifier is automatically integrated in the linear
rotary motor and provides a measuring signal of +-10 VDC suitable for the LinMot drive.
Factory calibrations of integrated torque sensors are always carried out in the installed state. This has the
advantage that the influences of the mechanics and the linear rotary motor are included.
•The torque measuring shaft is used to measure static as well as dynamic torques. The
sensor can measure both right-hand and left-hand loads. The measured variable is
suitable for control, regulation and monitoring tasks.
•Torque peaks exceeding the permissible overload (see specifications in the PR02 data
sheet) can lead to destruction of the torque measuring shaft. Where such peaks cannot
be safely excluded, they must be mitigated.
•When changing between right and left load, the torque sensor may show a small
hysteresis. This may cause the sensor to exceed the specified accuracy at the
changeover point.
•Simultaneously turning and measuring the force can falsify the measurement (e.g. due
to increased friction of the linear rotary shaft).
•The operating temperature range of the sensors is 5 - 45 °C. Above or below the limits,
there is a measurement error which influences the measurement results. It is
recommended to set the offset to zero before each measurement.
•The max. operating range is between 0 - 80 °C.
•For continuously precise measuring results, it is recommended to calibrate the torque
measuring shaft annually according to section 8.3.
•Recalibration is also strongly recommended after improper handling of the force
sensors (e.g. impacts on the linear rotary shaft or large overloads).
3.9 Option Force Sensor
The optional force sensor enables closed-loop force control with target force specification. The measurement
signal is also available to the user for the cyclical recording / evaluation of sensitive process data (e.g.
bounce force). This makes it easy to implement highly accurate, reproducible and recordable pressing &
assembly processes in accordance with Industry 4.0 requirements with high precision.
Force sensors are based on the measuring principle of strain gauges. They are designed to withstand
multiple mechanical overloads and still precisely detect the smallest forces. With this option, a suitable,
galvanically isolated measuring amplifier is automatically integrated in the linear rotary motor and provides a
measuring signal of +-10 VDC suitable for the LinMot drive.
Factory calibrations of integrated force sensors are always carried out in the installed state. This has the
advantage that the influences of the mechanics and the linear rotary motor are included.

Installation Guide Linear Rotary Motors ENG
Page 10 / 41 PR02-70 NTI AG / LinMot
•The force sensor is used to measure compressive and tensile forces. The measured
variable is suitable for control, regulation and monitoring tasks.
•Force peaks exceeding the permissible overload (see information in the PR02 data
sheet) can lead to destruction of the force sensor. Where such peaks cannot be safely
excluded, they must be mitigated.
•When changing between increasing and decreasing forces, the force sensor may show
a small hysteresis. This can lead to the sensor exceeding the specified accuracy at the
change point.
•Due to the static friction in the system, the force sensor measures more accurately if the
force vector always points in the same direction during repeated measurement
(influence of force hysteresis).
•To increase the measuring accuracy, linear rotary motors with integrated force sensor
technology are supplied without sealing lips / wipers.
•Simultaneous rotation and measurement of the force can falsify the measurement (e.g.
due to increased friction of the linear rotary shaft).
•The operating temperature range of the sensors is 5 - 45 °C. Above or below the limits,
there is a measurement error which influences the measurement results. It is
recommended to set the offset to zero before each measuring process.
•The max. operating range is between 0 - 80 °C.
•For continuously precise measurement results, it is recommended to calibrate the force
sensor annually according to section 8.3.
•Recalibration is also strongly recommended after improper handling of the force
sensors (e.g. impacts on the stroke rotating shaft or large overload).
3.10 Option Stainless Steel Front Flange (SSC)
The stainless steel front flange option offers the user hygiene at the highest level. Linear rotary motors with
this option can be used in machines and systems for processing food products or in the pharmaceutical and
medical industries. With this option, the user benefits from a partially increased IP degree of protection as
well as the possibility to use the front of the linear rotary motor even in extremely rough or corrosive
environments where aggressive cleaning agents are used.
•The exact list of materials used can be found in chapter 4.4.
•The user is obliged to check whether the cleaning agents used are compatible with the
materials of the stainless steel front flange.
•The stainless steel front flange may only be cleaned when the axle is at a standstill. It is
recommended that cleaning is carried out with the linear rotary shaft extended.
The linear rotary shaft must be dried before it is put back into operation.
•Any parts that do not belong to the zone of the stainless steel front flange may not be
corrosion-resistant and can therefore only be cleaned to a limited extent. They have a
reduced IP degree of protection.
•The specified IP degree of protection is achieved at standstill.

Installation Guide Linear Rotary Motors ENG
NTI AG / LinMot PR02-70 Page 11 / 41
4 Installation instructions
4.1 Operating Conditions
•Maximum ambient temperature limits: -10 °C…80 °C
•Internal temperature sensor error occurs at:
90 °C
120 °C (HP-Version)
•The max. installation altitude is 4'000 m above sea level.
From 1'000 m, derating of 1 °C per 100 m is to be considered for air cooling.
4.2 Assembly of the Linear Rotary Motor
The PR02-70 linear rotary motors have a centric fit (see chapter "Dimensions") on the front side, so that an
exact alignment of the rotary axis is possible.
Mounting only via the front screws is generally not sufficient (vibrations, transverse load) and must be
supplemented by another support. For reasons of vibration, a support as far back as possible is preferable.
PR02-70 linear rotary motors do not have T-slots for horizontal mounting. The main
mounting orientation of this motor family is intended to be vertical.
Option A) Option B)
There are 2 mounting options for stable vertical
mounting of the linear rotary motor.
Option A): The threaded holes on the side can be
used. In addition, the front of the motor should be
fixed using the 4 threaded holes. The positions of
the threaded holes can be found in the
"Dimensions" section.
Option B): An external support to the underside of
the motor can be created using the mounting flange
accessory (see accessories for more information).
In addition, the front of the motor should be fixed
using the 4 threaded holes. The positions of the
threaded holes can be found in the "Dimensions"
section.

Installation Guide Linear Rotary Motors ENG
Page 12 / 41 PR02-70 NTI AG / LinMot
4.3 Mounting the Load on the Shaft
The load mass is mounted by a shaft-hub clamping. The shaft-hub clamping is a non-positive connection
which is produced by means of two conical rings. The use of drivers or the production of grooves is
completely eliminated. The suitable shaft-hub clamping type can be ordered from LinMot. Mounting
instructions and ordering information can be found in the "Accessories" chapter.
4.4 Material Data
Different materials are used depending on the design of the linear rotary motor.
4.4.1 Standard Design
Component
Material
Linear Rotary Shaft
Quenched and tempered steel 1.0601 / C60
Front Flange
Stainless Steel 1.4305
Linear Ball Bearing
Steel
Wiper
NBR
Housing Linear Rotary Motor
Hard anodized aluminium 3.3206
4.4.2 Stainless Steel Front SSC
Component
Material
Linear Rotary Shaft
Stainless Steel 1.4112
Front Flange
Stainless Steel 1.4404
Linear Ball Bearing
Stainless Steel
Wiper
NBR 80 FDA
Housing Linear Rotary Motor
Hard anodized aluminium 3.3206

Installation Guide Linear Rotary Motors ENG
NTI AG / LinMot PR02-70 Page 13 / 41
5 Connections
5.1 Electrical Connection
Only connect or disconnect the motor connector and sensor cable if no voltage is applied to
the servo drive!
Only original LinMot cables may be used for wiring the motor and sensor! Even assembled
cables may only be manufactured from the original LinMot accessories and must be
checked carefully before commissioning!
Incorrect motor wiring can damage the motor and/or the servo drive!
5.1.1 Motor Cable
Three types of cables are available for the linear rotary motors. The standard motor cable is intended for
stationary installation. The High-Flex cable (suitable for cable tracks) and the robot cable are used for
moving cable applications.
Wiring Linear Rotory Motor
Wiring
torque measuring
shaft / force
sensor
Standard cable
High-flex cable
Robot cable
High-flex cable
Cable type
K15-04/05
KS10-04/05
KR05-04/05
KSS02-08
Min. bending radius
stationary
50 mm
(1.97 in)
50 mm
(1.97 in)
50 mm
(1.97 in)
35 mm
Min. bending radius
moving
Not suitable for
applications with
moving motor
cable
100 mm
(3.94 in)
No torsion
80 mm
(3.15 in)
Max. torsion:
±270° pro 0.5 m
61 mm
Approval
Cable material
acc. UL
UL / CSA 300V
UL / CSA 300V
Cable material acc.
UL
Material wire
insulation
TPE-U
TPE-E
TPE-E
PP
Material cable sheath
PUR
PUR
PUR
PUR
Oil resistance
very good
very good
very good
good
Chemical resistance
(to acids, alkalis,
solvents, hydraulic
fluid)
good
good
good
good
moderate for acids
Outdoor durability
very good
very good
very good
good
Flammability
flame retardant
flame retardant
flame retardant
flame retardant

Installation Guide Linear Rotary Motors ENG
Page 14 / 41 PR02-70 NTI AG / LinMot
5.1.2 Wiring Linear Rotary Motor
The following diagram shows the connection of the linear rotary motor and the options torque measuring
shaft and force sensor with the LinMot drive.

Installation Guide Linear Rotary Motors ENG
NTI AG / LinMot PR02-70 Page 15 / 41
5.1.3 Overview of the Connectors
Pos. 1: E-Pusher
Pos. 2: Linear motor
Pos. 3: Rotary motor
Pos. 4: Torque sensor
Pos. 5: Force sensor
5.1.4 Connector Wiring Linear Rotary Motor
View: Motor connector, plug side
Connector wiring
Linear Motor:
C-Connector
Rotary Motor:
C-Connector
Wire color
Motor cable
Ph 1+ / Ph A
A
A
red
Ph 1- / Ph B
B
B
pink
Ph 2+ / Ph C
C
C
blue
Ph 2- / (-)
D
D (not connected)
grey
+5VDC
E
E
white
GND
F
F
Inner shield
Sin
G
G
yellow
Cos
H
H
green
Temp.
L
L
black
Shield
Housing
Housing
Outer shield
Extension cables are double shielded. The two shields of the extension cables must not be
connected together: the inner shield of the extension cables is used as GROUND and must
be connected to GROUND*; only the outer shield must be connected to SHIELD* of the
connector.

Installation Guide Linear Rotary Motors ENG
Page 16 / 41 PR02-70 NTI AG / LinMot
5.1.5 Connector Wiring Torque Measuring Shaft / Force Sensor
View: Motor connector, plug side
Connector wiring
Torque Sensor:
M12 Connector (A-coded)
Wire colour
Sensor cable
Supply GND
1
white
Supply 24V (approx. 80 mA @ 24VDC)
2
brown
Do not connect
3
green
Torque / Force -
4
yellow
Torque / Force +
5
grey
AGND / reference ground for the torque
sensor signal (isolated from supply GND;
connect to reference GND of the analogue
input on the servo drive).
6
pink
Do not connect
7
blue
Do not connect
8
red
Bridges from Supply Ground and Signal Ground
•PIN 4 (force -) and PIN 1 (supply GND) are internally galvanically isolated and must not
be connected to each other. This applies to sensors with a 10-digit serial number.
Format = 0123.456.789.
•For torque sensors with 9-digit serial number (format = 123456789) PIN 4 (torque -) and
PIN 1 (supply GND) may be bridged at the supply source (not at the transducer), if
necessary, because the galvanic isolation is not present there. Make the connection as
close as possible to the drive to avoid potential differences with respect to the drive
GND
•The 24VDC supply must be protected with a 1AT fuse.
•The +24V supply must not be connected / disconnected when voltage is present. The
DC supply must not be switched on the secondary side of the power supply unit.
•It is recommended to connect pin 6 (AGND) to the reference ground of the analogue
input of the drive - in case of LinMot drives pin X4.1. realise connection as close to the
drive as possible to avoid potential differences compared to the drive GND.
•External EMC circuitry: a ceramic capacitor 100nF / 50V can optionally be soldered
between pin 4 and pin 5 on the evaluation electronics to reduce conducted interference.

Installation Guide Linear Rotary Motors ENG
NTI AG / LinMot PR02-70 Page 17 / 41
5.2 Connector Wiring Electric Pusher
View: Motor connector, plug side
Connector wiring
Electric Pusher
R-Connector
Wire colour
Motor cable
Ph 1+ / Ph A
1
red
Ph 1- / Ph B
2
pink
Ph 2+ / Ph C
3
blue
Ph 2- / (-)
4
grey
+5VDC
A
white
GND
B
Inner shield
Sin
C
yellow
Cos
D
green
Temp.
E
black
Shield
Housing
Outer shield
5.3 Connection of Air
Configuration of air connection
Pos. 1: Air connection with option (L01) / "Pull" with option Pn. Pusher
Pos. 2: "Push" with option Pn. Pusher
The PR02-70 is optionally equipped with a hollow shaft for air feed-through or for integration of a pneumatic
pusher. Depending on the option, there are several pneumatic push-in fittings (external hexagon M5) for a Ø
4 mm hose at the rear of the motor, above the electrical plug connections. Inside the motor, a Ø 4 mm air
hose is routed along the rotary shaft. This enables the user to realise pneumatic applications with an
operating pressure of max. 6 bar.
Depending on the order situation (option "hollow shaft" or option "pneumatic pusher"), 1 or 2 push-in
connections are pre-assembled. The user also has the option of mounting a pneumatic push-in fitting on the
front of the shaft. For this purpose, the user has an M5 (15 mm deep) in the axial direction and an M5 (5 mm
deep, recommended push-in fitting KAH04-M5 with a total length of 17 mm) in the radial direction. The
through hole in the rotary shaft is Ø 4 mm.
In the case of vacuum application, it is recommended to use a unit with sufficient power, as experience has
shown that all air coupling points generate small losses.
Push-in fitting
External hexagon M5
for a Ø 4 mm hose
2
41
A
B
C
D
E
3

Installation Guide Linear Rotary Motors ENG
Page 18 / 41 PR02-70 NTI AG / LinMot
6 Start-up
Please note that motors of the PR02-70 family are only fully supported from LinMot-Talk
version 6.10 onwards. It is therefore strongly recommended not to use an older LinMot-Talk
version.
6.1 Linear Motor and Rotary Motor
Linear motor and rotary motor are electrically independent units. The linear rotary motor can therefore be
commissioned sequentially. It does not matter which motor (linear motor or rotary motor) is commissioned
first.
The various parameters for the linear motor and the rotary motor are set on the drive side using the
corresponding wizard in the LinMot Talk configuration program.
Do not drive into the internal mechanical stops!
It must always be ensured that the linear motor never moves into the lower or upper internal
stop during operation, as otherwise the linear rotary motor may be damaged! The inner
stops may be used for homing purposes; the homing speed must not exceed 0.01 m/s.
6.2 Default Values of the Coordinate System
6.2.1 Angle of Rotation
Looking into the shaft, the counterclockwise
counting direction of the rotation angle is defined as
positive.
6.2.2 Position
With regard to the motor, the positive counting
direction of the position is defined by retracting the
linear rotary shaft.
The direction of rotation or position can be changed from LinMot-Talk version 6.8.

Installation Guide Linear Rotary Motors ENG
NTI AG / LinMot PR02-70 Page 19 / 41
6.3 Torque Measuring Shaft
Stroke rotary modules of the LinMot PR02 motor family can optionally have a torque
measuring shaft built into the module. Please make sure that the option „Torque measuring
shaft“ is selected during the ordering process. Fitting of the torque measuring shaft
afterwards is not possible.
6.3.1 Torque Operating Direction
Looking into the shaft, the anti-clockwise direction is defined as
positive.
The direction of rotation can be changed from LinMot-Talk version 6.8 onwards. This has an
influence on the parameterization of the torque measuring shaft.
6.4 Force Sensor
Linear rotary motors of the LinMot PR02 motor family can optionally have a force sensor
built into the module. Please make sure that the option „Force sensor“ is selected during the
ordering process. Fitting of force sensor afterwards is not possible.
6.4.1 Force Operating Direction
Extended Stroke mm
Looking to the motor, the positive stroke (force)
direction is defined by retracting the linear rotary
shaft.
The direction of stroke can be changed from LinMot-Talk version 6.8 onwards. This has an
influence on the parameterization of the force sensor as the positive force direction will
change as well.

Installation Guide Linear Rotary Motors ENG
Page 20 / 41 PR02-70 NTI AG / LinMot
6.5 Magnetic Spring MagSpring®
LinMot PR02 linear rotary motors can optionally be equipped with a MagSpring. Please
ensure that the "MagSpring" option is selected during the ordering process. The MagSpring
cannot be retrofitted.
6.5.1 Force Direction
Extended Stroke
The built-in MagSpring is offered in 2 operating directions. With the
positive acting MagSpring, the linear rotary shaft is pulled in and
with the negative acting MagSpring, the shaft is ejected.
The order suffix is given in the following table.
Positive force direction
Negative force direction
MagSpring 60 N
MS04
MS54
6.6 Plug and Play Function for Linear Rotary Motors
LinMot linear rotary motors of the latest generation are Plug and Play capable (see motor label "PnP"). This
means that they register with the drive independently. The module- and motor-specific parameters are
automatically stored in the drive and the motor is ready for operation.
Application-specific parameters, such as cable length, load mass, PID control settings etc. can be entered by
the user using the Motor Wizard.
To do this, click on the Motor Wizard symbol in the task bar of the LinMot-Talk software.
Then follow the sequence of steps from chapter 6.7.2.
6.7 Setting Motor Parameters
The various parameters for the linear motor and the rotary motor are set via the corresponding motor wizard
in the LinMot Talk configuration program. To open the wizard, select the "Motor Wizard" icon in the task bar.
6.7.1 Selection of the Motor Data Files
If the connected motor is a module with plug and play functionality, the following step can be skipped.
If no "PnP" symbol is printed on the motor nameplate, the module and motor-specific parameters must be
loaded manually via the Motor Wizard. So-called motor data files are available for this purpose. The motor
data file corresponding to the module (*.adf or *.adp) must be selected in the first step of the Motor Wizard.
The linear rotary motors are located in the installation directory of the LinMot-Talk software (download at
www.linmot.com) in the folder "Motors\LinMot Linear Rotary Motors\...".
Please contact support if the motor data files are not available.