LinMot P01-23 User manual

NTI AG / LinMot Dok-Nr. 0185-0001-E_5V0_IG_Linear_Motors_P01
Installation Guide
Linear Motors
ENG
P01-23 / P01-37 / P01-48

Installation Guide Linear Motors ENG
Page 2 / 40 P01-23 / P01-37 / P01-48 NTI AG / LinMot
Content
1General information ................................................................................................................................. 4
1.1 Introduction........................................................................................................................................ 4
1.2 Explanation of symbols...................................................................................................................... 4
1.3 Qualified personnel............................................................................................................................ 4
1.4 Liability............................................................................................................................................... 4
1.5 Copyright............................................................................................................................................ 4
2Safety instructions ................................................................................................................................... 5
3Installation instructions........................................................................................................................... 7
3.1 Operating conditions.......................................................................................................................... 7
3.2 Instructions for installing the linear motor.......................................................................................... 7
3.3 Mounting the stator............................................................................................................................ 8
3.4 Mounting the payload to the slider..................................................................................................... 8
3.5 "Moving slider" installation............................................................................................................... 10
3.6 "Moving stator" installation............................................................................................................... 10
3.6.1 Assembling instruction................................................................................................................. 11
3.7 Minimum distance from slider.......................................................................................................... 13
3.7.1 Minimum distance from slider to slider ........................................................................................ 13
3.7.2 Minimum distance from slider to metallic parts............................................................................ 13
4Electrical connection ............................................................................................................................. 14
4.1 Motor cable...................................................................................................................................... 14
4.1.1 Technical data.............................................................................................................................. 14
4.2 Cable type stators............................................................................................................................ 15
4.3 Rotatability of motor connectors...................................................................................................... 15
4.4 Mounting clips.................................................................................................................................. 16
4.5 Shrink tubing.................................................................................................................................... 16
5Accessories ............................................................................................................................................ 17
5.1 Wipers.............................................................................................................................................. 17
5.1.1 Mounting the wiper ...................................................................................................................... 18
5.2 Mounting flanges ............................................................................................................................. 19
5.3 Fan kits for flanges .......................................................................................................................... 21
5.4 Slider mounting kits ......................................................................................................................... 22
5.4.1 Fixed bearing............................................................................................................................... 22
5.4.2 Floating bearing........................................................................................................................... 22
5.4.3 Complete mounting kit................................................................................................................. 23
6Maintenance and test instructions ....................................................................................................... 24
6.1 Stator connector assignment........................................................................................................... 24
6.2 Stator checking................................................................................................................................ 26
6.3 Maintenance of linear motors .......................................................................................................... 31
6.3.1 Mounting...................................................................................................................................... 31
6.3.2 Inspection..................................................................................................................................... 32
6.3.3 Cleaning....................................................................................................................................... 32
6.3.4 Cleaning agent / Lubricant ........................................................................................................... 32

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-23 / P01-37 / P01-48 Page 3 / 40
7Storage, transport, installation altitude ............................................................................................... 32
8Dimensions of stators............................................................................................................................ 33
8.1 PS01-23x80..................................................................................................................................... 33
8.2 PS01-23x80-R ................................................................................................................................. 33
8.3 PS01-23x160................................................................................................................................... 34
8.4 PS01-23x160-R ............................................................................................................................... 34
8.5 PS01-37x120................................................................................................................................... 35
8.6 PS01-37x120-C ............................................................................................................................... 35
8.7 PS01-37x240................................................................................................................................... 36
8.8 PS01-37x240-C ............................................................................................................................... 36
8.9 PS01-48x150G-HP-C ...................................................................................................................... 37
8.10 PS01-48x240-C ............................................................................................................................... 37
8.11 PS01-48x360-C ............................................................................................................................... 37
9Declaration of Conformity and CE-marking ........................................................................................ 38
10 CB Test Certificate............................................................................................................................. 39

Installation Guide Linear Motors ENG
Page 4 / 40 P01-23 / P01-37 / P01-48 NTI AG / LinMot
1 General information
1.1 Introduction
This manual includes instructions for the assembly, installation, maintenance, transport, and storage of linear
motors. The document is intended for electricians, mechanics, service technicians, and warehouse staff.
Be sure to observe the general safety instructions as well as those in each chapter at all times.
Keep this manual accessible to the assigned staff.
1.2 Explanation of symbols
Triangular warning symbols warn against a danger.
Round command symbols tell what to do.
1.3 Qualified personnel
All work such as transport, installation, commissioning and service is only allowed to be carried out by
qualified personnel. Qualified personnel in the sense of the safety instructions in this documentation are
persons who are familiar with the transport, installation, assembly, commissioning and operation of the
product and who have the appropriate qualifications.
This manual must be read carefully before transport, installation, commissioning, service and all safety-
related information must be adhered to.
1.4 Liability
NTI AG (as manufacturer of LinMot linear motors and MagSpring products) excludes all liability for damages
and expenses caused by incorrect use of the products. This also applies to false applications, which are
caused by NTI AG's own data and notes, for example in the course of sales, support or application activities.
It is the sole responsibility of the user to check the information and information provided by NTI AG regarding
their safety-relevant correctness. In addition, the entire responsibility for safety-related product functionality
lies exclusively with the user.Product warranties are void if products are used with stators, sliders, servo
drives or cables not manufactured by NTI AG unless such use was specifically approved by NTI AG.
NTI AG’s warranty is limited to repair or replacement as stated in our standard warranty policy as described
in our "terms and conditions" previously supplied to the purchaser of our equipment (please request copy of
same if not otherwise available). Further reference is made to our general terms and conditions.
1.5 Copyright
This work is protected by copyright.
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or
mechanical, including photocopying, recording, microfilm, storing in an information retrieval system, not even
for training purposes, or translating, in whole or in part, without the prior written consent of NTI AG.
LinMot® is a registered trademark of NTI AG.

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-23 / P01-37 / P01-48 Page 5 / 40
2 Safety instructions
Contusions
Sliders contain neodynium magnets and have a strong attractive force.
Careless handling could cause fingers or skin to become pinched between two sliders.
This may lead to contusions, bruises, and bone fractures.
When handling sliders, wear thick protective gloves and keep a minimum distance between
sliders. Refer to the "Minimum distance from slider" section for minimum distance.
To reduce the risk of injury, never more than one slider should be held or transported by the
same person without packaging.
Pacemaker / Implanted heart defibrillator
Sliders could affect the functioning of pacemakers and implanted heart defibrillators. For the
duration of a strong approach to a magnetic field, these devices switch into test mode and
will not function properly.
•If you wear one of those devices keep the following minimum distances between the
pacemaker / defibrillator and slider:
- Min. 250 mm (10ʺ) for slider Ø 27 mm and 28 mm (PL01-27 / 28 / PL10-28)
- Min. 150 mm (6ʺ) for slider Ø 19 mm and 20 mm (PL01-19 / 20)
- Min. 100 mm (4ʺ) for slider Ø 12 mm (PL01-12)
•Inform others who wear these devices to comply with these minimum distances!
Caution - Risk of Electric Shock !
Before working, make sure that there are no high voltages.
Fast-moving machine parts
The sliders of LinMot linear motors are fast-moving machine parts. All necessary
precautions must be taken to prevent persons approaching the moving elements during
operation (provide covers, guards, etc.).
Automatic restart
The motors can start automatically under certain cricumstances!
If necessary, a corresponding warning symbol must be provided and protection against
entering the hazardous area or a suitable safe electronic disconnection must be provided!
Risk of injury due to a defect or fault
For areas where a defect or fault can result in substantial property damage or even serious
personal injury, additional external precautions must be taken or devices must be installed
to ensure safe operation even if a defect or fault occurs (eg. suitable safe electronic
disconnection, mechanical interlocks, barriers, etc.).
Magnetic field
Magnets integrated in the sliders produce a strong magnetic field. They could damage TVs,
laptops, computer hard drives, credit and ATM cards, data storage media, mechanical
watches, hearing aids, and speakers.
•Keep magnets away from devices and objects that could be damaged by strong
magnetic fields.
•For the above mentioned objects, keep a minimum distance as described in the
"Pacemaker / implanted defibrillator" section.
•For non-anti-magnetic watches, keep the double minimum distance.

Installation Guide Linear Motors ENG
Page 6 / 40 P01-23 / P01-37 / P01-48 NTI AG / LinMot
Combustibility
When machining magnets, the drilling dust could easily ignite.
Machining the sliders and the magnets they contain is not permitted.
Burn hazard
The sliders of LinMot motors can reach temperatures of 80 °C, which may cause burns
upon contact.
Grounding
All metal parts that are exposed to contact during any user operation or servicing and likely
to become energized shall be reliably connected to the means for grounding.
Mechanical handling
Neodymium magnets are brittle and heat-sensitive.
Machining the sliders and the magnets they contain is not permitted.
•Colliding magnets could crack. Sharp splinters could be catapulted for several meters
and cause eye injury.
•By machining the sliders, heat would result which demagnetises the magnets.
Slider
Linear motor sliders consist of a high-precision, thin-walled stainless steel tube in which the
neodymium magnets are housed. The LinMot sliders should be handled with care.
Avoid contact with other sliders or iron parts as this can damage the magnets and the slider
surface. Do not grip the sliders with pliers, as this can also damage the surface. Do not use
sliders which are already damaged on the surface (scratches, deformation, etc.). This can
cause further damage to the stator.
Effects on people
According to the current level of knowledge, magnetic fields of permanent magnets do not
have a measurable positive or negative effect on people. It is unlikely that permanent
magnets constitute a health risk, but it cannot be ruled out entirely.
•For your own safety, avoid constant contact with magnets.
•Store large magnets at least one meter away from your body.
Temperature resistance
Keep slider away from unshielded flame or heat.
Temperature above 120°C will cause demagnetization.

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-23 / P01-37 / P01-48 Page 7 / 40
3 Installation instructions
3.1 Operating conditions
Maximum ambient temperature limits:
•Standard Motors: -10 °C…80 °C
•HP Motors: -10 °C…110 °C
Internal temperature sensor error occurs at:
•Standard Motors: 90 °C
•HP Motos: 120 °C
3.2 Instructions for installing the linear motor
Please attend to the safety instructions in chapter 2 during the assembling!
1. Clean the slider with a paper towel.
2. Lubricate the slider in accordance with the
‘lubrication order’ (see the section 6.3
Maintenance of linear motors)
3. Insert the slider in the defined direction (see
assembly step 4.).

Installation Guide Linear Motors ENG
Page 8 / 40 P01-23 / P01-37 / P01-48 NTI AG / LinMot
4. Checking the installed direction of slider
After the installation, the front end of the slider
is located at the opposite side of the stator from
the cable connector or cable exit.
3.3 Mounting the stator
The stator is mounted by clamping. The LinMot flange (see the section 5.2 Accessories) or a similar flange
can be used for this purpose. Most important is a broad clamping surface in order to provide good heat
dissipation. Forced air cooling can also increase the continuous force of the linear motor by up to a factor of
1.8.
The flange clamp must not deform the stator.
Make sure the torque on the clamp plate screws does not exceed the maximum value.
Type of flange
Max. torque for screws
PF02-23
4 Nm
PF02-37
8 Nm
PF01-48
12 Nm
Incorrect mounting
Small contact area prevents cooling of the linear
motor
Correct mounting
Better heat dissipation with the LinMot flange
Correct mounting
Forced air cooling with LinMot fan to increase the
continuous force rating.
3.4 Mounting the payload to the slider
The load is mounted as a fixed bearing using spherical washers and conical seats (see the section « Slider
mounting kits » ).
•To avoid shear force on slider and wear on stator, the payload has to be beared by a
linear guide.
•Slider back end should not be used for load mounting.
Slider front end with ring / notch

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-23 / P01-37 / P01-48 Page 9 / 40
When attaching the load, the wrench for tightening the load must be used only on the load-
facing side of the slider. Avoid torsional stress on slider (note the following figures).
Incorrect attachment
Correct attachment
Slider
Thread
Max. torque for screw (Dry)
12 mm
M 5
5.2 Nm
20 mm
M 8
22.5 Nm
28 mm
M 10
42 Nm

Installation Guide Linear Motors ENG
Page 10 / 40 P01-23 / P01-37 / P01-48 NTI AG / LinMot
3.5 "Moving slider" installation
In a "moving slider" installation, the stator is fixed and the slider is the moving part.
The load, borne by a linear guide, is attached directly to the end of the slider. In order to compensate for
misalignment, spherical axial bearings consisting of spherical washers and conical seats (see the section
Slider mounting kits) are used to connect to the load. The mounting kit of slider and an oversized hole for the
screw make it possible to adjust a radial and angle offset.
Mounted payload with radial and angle offset
3.6 "Moving stator" installation
Stator
Slider
Spherical washer and
conical seat
Linear guide
Linear bearing
Stator
Slider
Spherical washer and
conical seat
Linear bearing
Linear guide
Floating
bearing

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-23 / P01-37 / P01-48 Page 11 / 40
In "moving stator" applications, the slider is fixed and the stator is the moving part.
The load is attached to the stator, which is mounted on a linear guide. In order to avoid an overconstrained
bearing mount and compensate for alignment errors, the slider may be mounted on one end in a fixed
bearing with a spherical axial bearing. On the opposite end, the slider is mounted in a floating bearing.
Mounting kits are available for mounting the slider (see the section Slider mounting kits).
3.6.1 Assembling instruction
Please attend to the safety instructions in chapter 2 during the assembling!
If moving stator application is used, the minimum bending radius of the motor cable should
be adhered to. See chapter Cable, section Technical Data.
1. Mount stator to its support bearing.
2. Placing a spacer.
Put a spacer (wood, plastic, aluminium
with thickness 15 mm) between slider
and linear guide. The spacer prevents
injuries to the hands and damage to
the slider surface!
3. Insert slider into stator.

Installation Guide Linear Motors ENG
Page 12 / 40 P01-23 / P01-37 / P01-48 NTI AG / LinMot
4. Installing the slider using the fixed bearing
The fixed bearing is screwed to the front
end of the slider.
Do not tighten the screw yet!
5. Mount floating bearing
Do not tighten the screw!
The slider is allowed to extend into the
floating bearing no more than 15 mm!
6. Move stator (back end) to the fixed end of
slider, center slider in stator and tighten the
screw.
7. Move stator (front side) to the floating
bearing and tighten screws.
After the installation of the slider a safety label must be placed close to the slider.

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-23 / P01-37 / P01-48 Page 13 / 40
3.7 Minimum distance from slider
3.7.1 Minimum distance from slider to slider
The sliders are made of neodymium magnets and have a strong magnetic attraction.
It must be kept a minimum distance between the sliders. This minimized the risk of bruising and secondly,
the sliders do not influence each other through their magnetic fields.
Type of slider
PL01-12
PL01-20 / PL01-19
PL01-28 / PL01-27
PL10-28
PL01-12
30 mm
PL01-20 / PL01-19
50 mm
PL01-28 / PL01-27
80 mm
PL10-28
70 mm
The data are measured from slider center to slider center.
3.7.2 Minimum distance from slider to metallic parts
When installing linear motors in modules with metal parts near the slider, undesired forces can arise due to
magnetic attraction or eddy currents. These generally manifest as erratic and jerky positioning, or reduced
dynamics of the linear motor. In order to avoid this, minimum distances between the slider and any metal
parts are to be observed whenever metal materials are used nearby.
Linear Motor
Minimum distance from slider surface
to ferromagnetic parts (iron, steel, etc.)
Minimum distance from slider surface
to non-ferromagnetic metallic parts
(aluminum, bronze, stainless steel, etc.)
P01-23x…
10 mm
5 mm
P01-37x…
15 mm
7 mm
P01-48x…
20 mm
10 mm

Installation Guide Linear Motors ENG
Page 14 / 40 P01-23 / P01-37 / P01-48 NTI AG / LinMot
4 Electrical connection
4.1 Motor cable
Do not connect or disconnect motor when there is power on the servo drive.
Use only double-shielded original LinMot cable. Cables from other sources must be
checked precisely before commissioning.
Incorrect connections can destroy the drive and stator.
The stator is connected to protective earth via the motor cable. The screw connections of
the C and R connectors must be tightened up to the stop.
Three types of cables are available for linear motors. The cable attached to the stator is not
a high flex cable. For moving cable applications please use the special LinMot KS high flex
(suitable for cable tracks) or KR robot cable.
4.1.1 Technical data
Standard cable
High-Flex cable
Robot cable
Cable name
K05-04/05
K15-04/05
KS05-04/05
KS10-04/05
KR05-04/05
KR10-04/05
Minimum bending
radius for fixed
installation
25 mm
(1 in)
50 mm
(2 in)
30 mm
(1.2 in)
50 mm
(2 in)
40 mm
(1.6 in)
50 mm
(2 in)
Minimum bending
radius when
moving
Not suitable for
applications with
moving motor cable
60 mm
(2.4 in)
No torsion
100 mm
(4 in)
No torsion
80 mm
(3.2 in)
Max.
Torsion:
±270° pro
0.5 m
100 mm
(4 in)
Max.
Torsion:
±270° pro
0.5 m
Approval
UL / CSA 300V
UL / CSA 300V
UL / CSA 300V
Material wire
insulation
TPE-U
TPE-E
TPE-E
Material cable
sheath
PUR
PUR
PUR
Oil resistance
very good
acc. DIN VDE 0282
Part 10 + HD 22.10
very good
acc. DIN VDE 0282
Part 10 + HD 22.10
very good
acc. DIN VDE 0282
Part 10 + HD 22.10
Chemical
resistance (to
acids, alkalis,
solvents, hydraulic
fluid)
good
good
good

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-23 / P01-37 / P01-48 Page 15 / 40
4.2 Cable type stators
Maintain the minimum bending radius of the stator cable (see figure below). In moving applications, the
stator cable must not be moved.
Not correct!
Minimum bending radius not observed
Correct!
Minimum bending radius of 25 mm maintained.
4.3 Rotatability of motor connectors
The motor connectors R and C can be rotated in both directions. (see illustration below).
R-Connector C-Connector

Installation Guide Linear Motors ENG
Page 16 / 40 P01-23 / P01-37 / P01-48 NTI AG / LinMot
4.4 Mounting clips
M, C, and R cable type motors are supplied with mounting clips to fix the motor cables.
In moving stator applications, these clips prevent damage due to vibrations of the cable. The clips help to
attach the cable connection to the flange.
Mounting clip
Material: Polypropylene, grey
Item-No.: 0150-3076
LinMot PS01-37x120-M stator in a moving stator
application. The connectors are attached to the
flange with the mounting clips. The cable attached
to the motor is not moved and the minimum
bending radius is maintained.
4.5 Shrink tubing
The special heat shrinkable polypropylene tubing (Item-No. 0150-3076) protects the M, C and R-type
connector in applications with very difficult environmental conditions.

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-23 / P01-37 / P01-48 Page 17 / 40
5 Accessories
5.1 Wipers
Hinterer Abstreifer Vorderer Abstreifer
The stators are equipped as standard with wipers. This simplifies maintenance and the maintenance cycles
can be extended. The wiper effects that the lubricant is dispensed metered and does not leak outside of the
stator. The lubricant is less dirty.
For each wiper, the lengthwise installation space for the stator, increases by 12 mm or 14 mm.
PA01-37: 12mm (0.47in)
PA01-48: 14mm (0.55in)
PA01-23: 14mm (0.55in)
PA01-37: 12mm (0.47in)
PA01-48: 14mm (0.55in)

Installation Guide Linear Motors ENG
Page 18 / 40 P01-23 / P01-37 / P01-48 NTI AG / LinMot
5.1.1 Mounting the wiper
The wipers are inserted into the ends of the installed stator and secured with screws on the side. The stator
is then lubricated using the lube nipple (funnel) in the housing of the wiper.
Casing Wiper
Material
Casing: POM
Lube nipple (funnel D1a): Brass
Wiper: H-PU
Item
D
L
A
Weight
PA01-23/12-F
29mm (1.14in)
33mm (1.30in)
14mm (0.55in)
0.014kg
PA01-37/19-F*
45mm (1.77in)
32mm (1.26in)
12mm (0.47in)
0.028kg
PA01-37/19-R*
45mm (1.77in)
37mm (1.45in)
12mm (0.47in)
0.026kg
PA01-37/19-R cable*
45mm (1.77in)
40mm (1.57in)
12mm (0.47in)
0.030kg
PA01-37/20-F
45mm (1.77in)
32mm (1.26in)
12mm (0.47in)
0.028kg
PA01-37/20-R
45mm (1.77in)
37mm (1.45in)
12mm (0.47in)
0.026kg
PA01-37/20-R cable
45mm (1.77in)
40mm (1.57in)
12mm (0.47in)
0.030kg
PA01-48/27-F*
58mm (2.28in)
32mm (1.26in)
14mm (0.55in)
0.056kg
PA01-48/27-R*
58mm (2.28in)
32mm (1.26in)
14mm (0.55in)
0.050kg
PA01-48/28-F
58mm (2.28in)
32mm (1.26in)
14mm (0.55in)
0.056kg
PA01-48/28-R
58mm (2.28in)
32mm (1.26in)
14mm (0.55in)
0.050kg
Item
Description
Item-No.
PA01-23/12-F
Wiper for PS01-23x... front side
0150-3125
PA01-37/19-F*
Wiper for PS01-37x... front side
0150-3225
PA01-37/19-R*
Wiper for PS01-37x...-C rear side
0150-3226
PA01-37/19-R cable*
Wiper for PS01-37x... Cable rear side
0150-3227
PA01-37/20-F
Wiper for PS01-37x... front side
0150-3126
PA01-37/20-R
Wiper for PS01-37x...-C front side
0150-3201
PA01-37/20-R cable
Wiper for PS01-37x...-Cable rear side
0150-3221
PA01-48/27-F*
Wiper for PS01-48x... front side
0150-3228
PA01-48/27-R*
Wiper for PS01-48x...-C rear side
0150-3229
PA01-48/28-F
Wiper for PS01-48x... front side
0150-3127
PA01-48/28-R
Wiper for PS01-48x...-C rear side
0150-3202
* Wipers for linear motors with high-clearance sliders

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-23 / P01-37 / P01-48 Page 19 / 40
5.2 Mounting flanges
Max. Torque
(Clamping screws):
4 Nm (2.95 lbf ft)
Item
For Stator
Fan-Quantity
Std. / Max.
L
[mm]
A
[mm]
B
[mm]
Weight
[g / oz]
Item- No.
PF02-23x50
P01-23x80
1 / 1
50
15
10
115 / 4.1
0150-2102
PF02-23x120
P01-23x160
1 / 2
120
30
30
280 / 9.9
0150-2103
PF02-23x170
P01-23x160
1 / 2
170
45
40
390 / 13.8
0150-2117
PF02-23
Flanschprofil per
m
P01-23x…
(-)
(-)
(-)
(-)
(-)
0150-2101
Max. Torque (Clamping screws): 8 Nm (5.9 lbf ft)
Item
For Stator
Fan-Quantity
Std. / Max.
L
[mm]
A
[mm]
B
[mm]
Weight
[g / oz]
Item- No.
PF02-37x100
P01-37x120
1 / 1
100
25
25
450 / 15.9
0150-1998
PF02-37x140
P01-37x120
1 / 1
140
50
20
630 / 22.2
0150-2105
PF02-37x200
P01-37x240
1 / 2
200
50
50
920 / 32.5
0150-1999
PF02-37
Flanschprofil per
m
P01-37x…
(-)
(-)
(-)
(-)
(-)
0150-1997
Sliding block M6
(Art.-Nr. 0150-3245)
Sliding block M6
(Art.-Nr. 0150-3245)

Installation Guide Linear Motors ENG
Page 20 / 40 P01-23 / P01-37 / P01-48 NTI AG / LinMot
Max. Torque (Clamping screws): 12 Nm (8.85 lbf ft)
Item
For Stator
Fan-Quantity
Std. / Max.
L
[mm]
B
[mm]
Weight
[g / oz]
Item- No.
PF01-48x120
P01-48x240
1 / 1
120
25
970 / 34.2
0150-1976
PF01-48x226
P01-48x240
1 / 2
226
85
1855 / 65.4
0150-2108
PF01-48
Flanschprofil per m
P01-48x…
(-)
(-)
(-)
(-)
0150-2104
Max. Torque (Clamping screws): 12 Nm (8.85 lbf ft)
Item
For Stator
Fan-Quantity
Std. / Max.
L
[mm]
Weight
[g / oz]
Item- No.
PF01-48x346
P01-48x360
2 / 3
346
2840 / 100.2
0150-2145
Sliding block M6
(Art.-Nr. 0150-3245)
Sliding block M6
(Art.-Nr. 0150-3245)