LinMot P01-48-HP Series User manual

NTI AG / LinMot Dok-Nr. 0185-0125-E_1V1_IG_P01-48-HP-EX_Linear_Motors
Installation Guide
Linear Motors
ENG
P01-48-HP EX protected

Installation Guide Linear Motors ENG
Page 2 / 47 P01-48-HP EX protected NTI AG / LinMot
Content
1General information ................................................................................................................................. 4
1.1 Introduction........................................................................................................................................ 4
1.2 Explanation of symbols...................................................................................................................... 4
1.3 Qualified personnel............................................................................................................................ 4
1.4 Liability............................................................................................................................................... 4
1.5 Copyright............................................................................................................................................ 4
2Safety instructions ................................................................................................................................... 5
2.1 Appropriate application...................................................................................................................... 5
2.2 Warning signs.................................................................................................................................... 6
2.3 Additional ATEX safety instructions................................................................................................... 8
3Product description.................................................................................................................................. 9
3.1 Structure ............................................................................................................................................ 9
3.1.1 Linear Motor................................................................................................................................... 9
3.1.2 LinMot Servo Drive ........................................................................................................................ 9
3.1.3 Temperature relay ....................................................................................................................... 10
3.1.4 Circuit breaker.............................................................................................................................. 10
3.2 Exterior view .................................................................................................................................... 10
3.3 Interior view...................................................................................................................................... 11
3.4 Technical data ................................................................................................................................. 11
3.5 Performance characteristic.............................................................................................................. 16
3.6 Thermal behavior............................................................................................................................. 16
3.6.1 Internal temperature monitoring................................................................................................... 16
3.6.2 Higher-level temperature monitoring ........................................................................................... 18
3.7 Dimensions...................................................................................................................................... 19
3.7.1 PS01-48x150 with bearing PB01................................................................................................. 19
3.7.2 PS01-48x150 with bearing flange PB03...................................................................................... 20
3.7.3 PS01-48x240 with bearing PB01................................................................................................. 21
3.7.4 PS01-48x240 with bearing flange PB03...................................................................................... 22
3.7.5 PS01-48x360 with bearing PB01................................................................................................. 23
3.7.6 PS01-48x360 with bearing flange PB03...................................................................................... 24
3.8 Marking............................................................................................................................................ 25
3.9 Connector assignment..................................................................................................................... 25
3.10 Motor cable...................................................................................................................................... 26
3.11 Cabling............................................................................................................................................. 27
4Installation and commissioning............................................................................................................ 27
4.1 Operating conditions........................................................................................................................ 27
4.2 Mounting the motor.......................................................................................................................... 28
4.3 Mounting the flange ......................................................................................................................... 29
4.4 Mounting the payload to the slider................................................................................................... 29
4.5 «Moving slider» installation.............................................................................................................. 30
4.6 Electrical connection of the motor ................................................................................................... 31
4.7 Check before commissioning........................................................................................................... 32

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-48-HP EX protected Page 3 / 47
4.8Design of water cooling ................................................................................................................... 32
4.8.1 Determination of the max. possible amount of cont. power dissipation Pv_Max ........................ 33
4.8.2 Determination of water flow Q ..................................................................................................... 33
4.8.3 Determination of water pressure Δp............................................................................................ 34
4.8.4 Corrosion protection .................................................................................................................... 34
4.8.5 Cooling line connection................................................................................................................ 34
5Accessories ............................................................................................................................................ 35
5.1 Slider mounting kit fixed bearing ..................................................................................................... 35
5.2 Cooling Flange................................................................................................................................. 35
6Maintenance and test instructions ....................................................................................................... 36
6.1 Maintenance schedule..................................................................................................................... 36
6.2 Cleaning in assembled state............................................................................................................ 37
6.3 Cleaning in disassembled state....................................................................................................... 37
6.4 Cleaning agent................................................................................................................................. 37
6.5 Stator checking................................................................................................................................ 37
7Storage, transport, installation height ................................................................................................. 39
8Declaration of Conformity ..................................................................................................................... 40
9IECEx Conformity certificate................................................................................................................. 41
10 EC Type examination certificate ...................................................................................................... 45

Installation Guide Linear Motors ENG
Page 4 / 47 P01-48-HP EX protected NTI AG / LinMot
1 General information
1.1 Introduction
This manual includes instructions for the assembly, installation, maintenance, transport, and storage of linear
motors. The document is intended for electricians, mechanics, service technicians, and warehouse staff.
Read this manual before using the product and observe the general safety instructions and those in the
relevant section at all times.
Keep these operating instructions in an accessible place and make them available to the personnel
assigned.
1.2 Explanation of symbols
Triangular warning signs warn of danger.
Round command symbols tell what to do.
1.3 Qualified personnel
All work such as installation, commissioning, operation and service of the product may only be carried out by
qualified personnel.
The personnel must have the necessary qualifications for the corresponding activity and be familiar with the
installation, commissioning, operation and service of the product. The manual and in particular the safety
instructions must be carefully read, understood and observed.
1.4 Liability
NTI AG (as manufacturer of LinMot and MagSpring products) excludes all liability for damages and
expenses caused by incorrect use of the products. This also applies to false applications, which are caused
by NTI AG's own data and notes, for example in the course of sales, support or application activities. It is the
responsibility of the user to check the data and information provided by NTI AG for correct applicability in
terms of safety. In addition, the entire responsibility for safety-related product functionality lies exclusively
with the user.Product warranties are void if products are used with stators, sliders, servo drives or cables not
manufactured by NTI AG unless such use was specifically approved by NTI AG.
NTI AG’s warranty is limited to repair or replacement as stated in our standard warranty policy as described
in our "terms and conditions" previously supplied to the purchaser of our equipment (please request copy of
same if not otherwise available). Further reference is made to our general terms and conditions.
1.5 Copyright
This work is protected by copyright.
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or
mechanical, including photocopying, recording, microfilm, storing in an information retrieval system, not even
for training purposes, or translating, in whole or in part, without the prior written consent of NTI AG.
LinMot® is a registered trademark of NTI AG.

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-48-HP EX protected Page 5 / 47
2 Safety instructions
2.1 Appropriate application
The linear motors of the types described here are used exclusively to carry out linear movements. The direct
drives are intended for use in industrial plants. The motors are only operated with original LinMot servo
drives. For external temperature monitoring, 2 temperature sensors and a temperature relay are used, which
interrupts the power supply in the event of a fault. The motors are intended for use in potentially explosive
atmospheres which occasionally occur (zone classification 1, 21, 2, 22 according to DIN EN 60079-14).
Explosivity can consist of gases, vapours, mists and dust. The motors are dimensioned for an ambient
temperature of 0 °C to 60 °C. The motors are designed for a temperature range of 0 °C to 50 °C. The user
determines the operating conditions and thus the maximum surface temperature of the device by means of
the specific type of application of the motors. This allows several temperature classes to be assigned. The
ATEX motors used here correspond to temperature class T4 (max. surface temperature = 135 °C) and T6
(max. surface temperature = 85 °C) according to DIN EN 60079-14. According to this, the devices may be
used in an explosive atmosphere in which the ignition temperature is above the max. surface temperature.

Installation Guide Linear Motors ENG
Page 6 / 47 P01-48-HP EX protected NTI AG / LinMot
2.2 Warning signs
Contusions
Sliders contain neodynium magnets and have a strong attractive force.
Careless handling could cause fingers or skin to become pinched between two sliders.
This may lead to contusions, bruises, and bone fractures.
When handling sliders, wear thick protective gloves and keep a minimum distance between
sliders. Refer to the "Minimum distance from slider" section for minimum distance.
To reduce the risk of injury, never more than one slider should be held or transported by the
same person without packaging.
Pacemaker / Implanted heart defibrillator
Sliders could affect the functioning of pacemakers and implanted heart defibrillators. For the
duration of a strong approach to a magnetic field, these devices switch into test mode and
will not function properly.
•If you wear one of those devices keep the following minimum distances between the
pacemaker / defibrillator and slider:
- Min. 250 mm (10ʺ) for slider Ø 27 mm and 28 mm (PL01-27 / 28 / PL10-28)
- Min. 150 mm (6ʺ) for slider Ø 19 mm and 20 mm (PL01-19 / 20)
- Min. 100 mm (4ʺ) for slider Ø 12 mm (PL01-12)
•Inform others who wear these devices to comply with these minimum distances!
Caution - Risk of Electric Shock !
Before working, make sure that there are no high voltages.
Fast-moving machine parts
The sliders of LinMot linear motors are fast-moving machine parts. All necessary
precautions must be taken to prevent persons approaching the moving elements during
operation (provide covers, guards, etc.).
Automatic restart
The motors can start automatically under certain cricumstances!
If necessary, a corresponding warning symbol must be provided and protection against
entering the hazardous area or a suitable safe electronic disconnection must be provided!
Risk of injury due to a defect or fault
For areas where a defect or fault can result in substantial property damage or even serious
personal injury, additional external precautions must be taken or devices must be installed
to ensure safe operation even if a defect or fault occurs (eg. suitable safe electronic
disconnection, mechanical interlocks, barriers, etc.).
Magnetic field
Magnets integrated in the sliders produce a strong magnetic field. They could damage TVs,
laptops, computer hard drives, credit and ATM cards, data storage media, mechanical
watches, hearing aids, and speakers.
•Keep magnets away from devices and objects that could be damaged by strong
magnetic fields.
•For the above mentioned objects, keep a minimum distance as described in the
"Pacemaker / implanted defibrillator" section.
•For non-anti-magnetic watches, keep the double minimum distance.

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-48-HP EX protected Page 7 / 47
Combustibility
When machining magnets, the drilling dust could easily ignite.
Machining the sliders and the magnets they contain is not permitted.
Burn hazard
The sliders of LinMot motors can reach temperatures of 80 °C, which may cause burns
upon contact.
Grounding
All metal parts that are exposed to contact during any user operation or servicing and likely
to become energized shall be reliably connected to the means for grounding.
Mechanical handling
Neodymium magnets are brittle and heat-sensitive.
Machining the sliders and the magnets they contain is not permitted.
•Colliding magnets could crack. Sharp splinters could be catapulted for several meters
and cause eye injury.
•By machining the sliders, heat would result which demagnetises the magnets.
Slider
Linear motor sliders consist of a high-precision, thin-walled stainless steel tube in which the
neodymium magnets are housed. The LinMot sliders should be handled with care.
Avoid contact with other sliders or iron parts as this can damage the magnets and the slider
surface. Do not grip the sliders with pliers, as this can also damage the surface. Do not use
sliders which are already damaged on the surface (scratches, deformation, etc.). This can
cause further damage to the stator.
Effects on people
According to the current level of knowledge, magnetic fields of permanent magnets do not
have a measurable positive or negative effect on people. It is unlikely that permanent
magnets constitute a health risk, but it cannot be ruled out entirely.
•For your own safety, avoid constant contact with magnets.
•Store large magnets at least one meter away from your body.
Temperature resistance
Keep slider away from unshielded flame or heat.
Temperature above 150°C will cause demagnetization.

Installation Guide Linear Motors ENG
Page 8 / 47 P01-48-HP EX protected NTI AG / LinMot
2.3 Additional ATEX safety instructions
Assembly, commissioning, and maintenance of the motors may be performed only by
qualified personnel who are familiar with the directives of DIN EN 60079-14.
Maintenance and service work may be performed only in a clean room with no explosive
atmosphere. Dangerous ignition sources may arise when disassembling component parts.
Only original parts from LinMot may be used for commissioning and maintenance work.
The stator is grounded via the motor cable. The connector must be firmly tightened.
Observe the specified tightening torque in chapter 3.9.
Do not separate when energized.
Operation is allowed only in conjunction with a temperature relay and circuit breaker.
Only for use with a LinMot inverter.
The permissible ambient temperature for operating the motor is 0 °C ... +60°C.

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-48-HP EX protected Page 9 / 47
3 Product description
3.1 Structure
LinMot ATEX linear motors are assembled into a complete servo drive system consisting of several
connected components (see the illustration below). Only the motor is located in the "hazardous" area, all
other components are located on the "safe" side.
« Safe side »
Control cabinet
« Hazardous side »
EX environment
Pos. 1: Circuit breaker Pos. 6: Signals (Motorcom., Internal temp. monitoring)
Pos. 2: Power supply Pos. 7: Linear motor
Pos. 3: Control unit «LinMot Drive» Pos. 8: Temperature sensors Pt1000
Pos. 4: Temperature relay Pos. 9: Pt1000 temperature signals
Pos. 5: Power
3.1.1 Linear Motor
LinMot motors are direct-drive electromagnetic tubular linear motors.
The main components of the motor are the stator and the slider. The slider, the so-called "magnet bar",
consists of permanent magnets that are arranged with alternating polarization. The stator contains the
windings and position sensors. The windings are fed with current at an appropriate electrical phase angle,
like a permanently excited synchronous motor, thus producing a force in the desired direction. The motor has
2 to 4 temperature sensors on the windings depending on the length. These sensors can be used with a
series x1100 or x1200 LinMot drive to read and analyze the absolute temperature. This allows the winding
temperature to be determined and the motor to be switched off if the motor runs too hot. If the drive can no
longer communicate with the motor, then it will shift to a fault state. Feedback is provided to the control
system. The position is sensed by measuring the magnetic field of the slider.
The stator is encapsulated and welded completely shut.
ATEX linear motors can be equipped with a copper cooling system as an option.
3.1.2 LinMot Servo Drive
Takes over the current control, positioning control and temperature monitoring of the motor as well as
monitoring the power section.

Installation Guide Linear Motors ENG
Page 10 / 47 P01-48-HP EX protected NTI AG / LinMot
3.1.3 Temperature relay
Receives values from the Pt1000 temperature sensors mounted on the exterior of the motor under the
stainless steel housing. In case of a fault (overtemperature), it initiates the interruption of the power supply to
the servo drive. Feedback to the machine control system.
3.1.4 Circuit breaker
Interrupts the system power supply if the maximum surface temperature setting is exceeded.
3.2 Exterior view
Pt1000 sensors under
stainless steel housing
Copper tubing for
water cooling
Stator with windings (encapsulated)
Water cooling
connection

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-48-HP EX protected Page 11 / 47
3.3 Interior view
3.4 Technical data
PS01-48x150G-HP-EX-E (Art: 0150-4370)
PS01-48x150G-HP-EX-E-FC (Art: 0150-4371)
Stroke
mm
(in)
80
(3.15)
170
(6.69)
290
(11.42)
380
(14.96)
470
(18.49)
590
(23.23)
680
(26.75)
890 *
(35.04)
1070 *
(42.13)
Maximum force
E12x0-UC
N
(lbf)
310
(69.70)
Maximum force
E11x0-XC
N
(lbf)
310
(69.70)
Nominal force
N
(lbf)
65
(14.60)
Nom. force, liquid cooled
N
(lbf)
175
(39.35)
Force constant
N/A
(lbf/A)
21.9
(5.14)
Max. Current @ 72VDC
A
14.1
Max. Speed @ 72VDC
m/s
(in/s)
3.0
(118)
Phase resist. 25/120 °C
Ohm
0.87 / 1.2
Phase inductivity
mH
0.7
Stator diameter
mm
(in)
60
(2.36)
Stator length
mm
(in)
255
(10.04)
Stator mass
g
(lb)
2742
(6.05)
Slider diameter
mm
(in)
27
(0.059)
Slider length
mm
(in)
410
(16.14)
500
(19.69)
620
(24.41)
710
(27.95)
800
(31.50)
920
(36.22)
1010
(39.76)
1220
(48.03)
1400
(55.12)
Slider mass
g
(lb)
1620
(3.57)
2010
(4.43)
2530
(5.58)
2920
(6.44)
3310
(7.30)
3830
(8.44)
4220
(9.30)
5130
(11.31)
5910
(13.03)
Repeatability
mm
(in)
±0.05
(±0.0020)
Linearity
%
±0.10
Repeatability with EPS
mm
(in)
±0.01
(±0.0004)
Linearity with EPS
mm
(in)
±0.01
(±0.0004)
* on request

Installation Guide Linear Motors ENG
Page 12 / 47 P01-48-HP EX protected NTI AG / LinMot
Ordering information
Item
Description
Item-No.
PS01-48x150G-HP-EX-E
Stator HP, EX, IP67
0150-4370
PS01-48x150G-HP-EX-E-FC
Stator HP, EX, IP67, FC
0150-4371
Item
Description
Slider length mm (in)
Item-No.
PL01-27x410/330
Slider 'high clearance'
410 (16.14)
0150-1468
PL01-27x500/420
Slider 'high clearance'
500 (19.69)
0150-1469
PL01-27x620/540
Slider 'high clearance'
620 (24.41)
0150-1470
PL01-27x710/630
Slider 'high clearance'
710 (27.95)
0150-1471
PL01-27x800/720
Slider 'high clearance'
800 (31.50)
0150-1472
PL01-27x920/840
Slider 'high clearance'
920 (36.22)
0150-1447
PL01-27x1010/930
Slider 'high clearance'
1010 (39.76)
0150-1473
PL01-27x1220/1140
Slider 'high clearance'
1220 (48.03)
0150-1587
PL01-27x1400/1320
Slider 'high clearance'
1400 (55.12)
0150-1588
Item
Description
Item-No.
PB01-48x25-80-E-SSC
Bearing for PS01-48x...-SSC (Stainless)
0150-4190
PB03-48x25-80-E-SSC
Bearing for PS01-48x...-SSC (Stainless)
0150-4191

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-48-HP EX protected Page 13 / 47
PS01-48x240F-HP-EX-E (Art: 0150-4365)
PS01-48x240F-HP-EX-E-FC (Art: 0150-4366)
Stroke
mm
(in)
80
(3.15)
200
(7.87)
290
(11.42)
380
(14.96)
500
(19.69)
590
(23.23)
800
(31.50)
980
(38.58)
Maximum force
E12x0-UC
N
(lbf)
496
(111.51)
Maximum force
E11x0-XC
N
(lbf)
477
(107.23)
Nominal force
N
(lbf)
98
(22.03)
Nom. force, liquid
cooled
N
(lbf)
280
(62.95)
Force constant
N/A
(lbf/A)
19.1
(4.29)
Max. Current @ 72VDC
A
25.9
Max. Speed @ 72VDC
m/s
(in/s)
3.4
(134)
Phase resist. 25/120 °C
Ohm
0.97 / 1.3
Phase inductivity
mH
1.1
Stator diameter
mm
(in)
60
(2.36)
Stator length
mm
(in)
345
(13.58)
Stator mass
g
(lb)
3710
(8.18)
Slider diameter
mm
(in)
27
(0.059)
Slider length
mm
(in)
500
(19.69)
620
(24.41)
710
(27.95)
800
(31.50)
920
(36.22)
1010
(39.76)
1220
(48.03)
1400
(55.12)
Slider mass
g
(lb)
2010
(4.43)
2530
(5.58)
2920
(6.44)
3310
(7.30)
3830
(8.44)
4220
(9.30)
5130
(11.31)
5910
(13.03)
Repeatability
mm
(in)
±0.05
(±0.0020)
Linearity
%
±0.10
Repeatability with EPS
mm
(in)
±0.01
(±0.0004)
Linearity with EPS
mm
(in)
±0.01
(±0.0004)
Ordering information
Item
Description
Item-No.
PS01-48x240F-HP-EX-E
Stator HP, EX, IP67
0150-4365
PS01-48x240F-HP-EX-E-FC
Stator HP, EX, IP67, FC
0150-4366
Item
Description
Slider length mm (in)
Item-No.
PL01-27x500/420
Slider 'high clearance'
500 (19.69)
0150-1469
PL01-27x620/540
Slider 'high clearance'
620 (24.41)
0150-1470
PL01-27x710/630
Slider 'high clearance'
710 (27.95)
0150-1471
PL01-27x800/720
Slider 'high clearance'
800 (31.50)
0150-1472
PL01-27x920/840
Slider 'high clearance'
920 (36.22)
0150-1447
PL01-27x1010/930
Slider 'high clearance'
1010 (39.76)
0150-1473
PL01-27x1220/1140
Slider 'high clearance'
1220 (48.03)
0150-1587

Installation Guide Linear Motors ENG
Page 14 / 47 P01-48-HP EX protected NTI AG / LinMot
PL01-27x1400/1320
Slider 'high clearance'
1400 (55.12)
0150-1588
Item
Description
Item-No.
PB01-48x25-80-E-SSC
Bearing for PS01-48x...-SSC (Stainless)
0150-4190
PB03-48x25-80-E-SSC
Bearing for PS01-48x...-SSC (Stainless)
0150-4191

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-48-HP EX protected Page 15 / 47
PS01-48x360F-HP-EX-E (Art: 0150-4367)
PS01-48x360F-HP-EX-E-FC (Art: 0150-4368)
Stroke
mm
(in)
80
(3.15)
170
(6.69)
260
(10.24)
380
(14.96)
470
(18.50)
680
(26.77)
860
(33.86)
Maximum force
E12x0-UC
N
(lbf)
721
(162.1)
Maximum force
E11x0-XC
N
(lbf)
562
(126.3)
Nominal force
N
(lbf)
151
(34.9)
Nom. force, liquid cooled
N
(lbf)
408
(91.7)
Force constant
N/A
(lbf/A)
27.7
(6.23)
Max. Current @ 72VDC
A
25.9
Max. Speed @ 72VDC
m/s
(in/s)
2.35
Phase resistance 25/120 °C
Ohm
1.4 / 1.9
Phase inductivity
mH
1.6
Stator diameter
mm
(in)
60
(2.36)
Stator length
mm
(in)
465
(18.31)
Stator mass
g
(lb)
5000
(11.02)
Slider diameter
mm
(in)
27
(0.059)
Slider length
mm
(in)
620
(24.41)
710
(27.95)
800
(31.50)
920
(36.22)
1010
(39.76)
1220
(48.03)
1400
(55.12)
Slider mass
g
(lb)
2530
(5.58)
2920
(6.44)
3310
(7.30)
3830
(8.44)
4220
(9.30)
5130
(11.31)
5910
(13.03)
Repeatability
mm
(in)
±0.05
(±0.0020)
Linearity
%
±0.10
Repeatability with EPS
mm
(in)
±0.01
(±0.0004)
Linearity with EPS
mm
(in)
±0.01
(±0.0004)
Ordering information
Item
Description
Item-No.
PS01-48x360F-HP-EX-E
Stator HP, EX, IP67
0150-4367
PS01-48x360F-HP-EX-E-FC
Stator HP, EX, IP67, FC
0150-4368
Item
Description
Slider length mm (in)
Item-No.
PL01-27x620/540
Slider 'high clearance'
620 (24.41)
0150-1470
PL01-27x710/630
Slider 'high clearance'
710 (27.95)
0150-1471
PL01-27x800/720
Slider 'high clearance'
800 (31.50)
0150-1472
PL01-27x920/840
Slider 'high clearance'
920 (36.22)
0150-1447
PL01-27x1010/930
Slider 'high clearance'
1010 (39.76)
0150-1473
PL01-27x1220/1140
Slider 'high clearance'
1220 (48.03)
0150-1587
PL01-27x1400/1320
Slider 'high clearance'
1400 (55.12)
0150-1588

Installation Guide Linear Motors ENG
Page 16 / 47 P01-48-HP EX protected NTI AG / LinMot
Artikel
Beschreibung
Art-Nr.
PB01-48x25-80-E-SSC
Bearing for PS01-48x...-SSC (Stainless)
0150-4190
PB03-48x25-80-E-SSC
Bearing for PS01-48x...-SSC (Stainless)
0150-4191
3.5 Performance characteristic
With the design software "LinMot Designer" software (download from the link
https://linmot.com/download/linmot-designer/), the key data corresponding to the required load situation,
such as peak force, nominal force, or maximum speed, can be calculated and presented. The motor
operating temperature can also be determined. This must be verified in the real application.
3.6 Thermal behavior
3.6.1 Internal temperature monitoring
Setting the motor internal temperature monitoring:
Operation in temperature class T4
The temperature monitoring configuration can be left in the default settings.
The nominal sensor operating temperature is 90°C. At 95 °C a warning is given and at 100 °C the drive goes
into error state. The LinMot-Designer program provides concrete information on the motion designs.
Logging in is necessary to view these parameters.
•User-ID: «SERVICE»
•Password: without (in default state)
T4 Max. Sensor Temperature (Default Setting)

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-48-HP EX protected Page 17 / 47
T4 Max. Winding Temperature (Default Setting)
Operation in temperature class T6
The sensor operating temperature is 60°C.
The parameters for temperature monitoring must be adjusted according to the following
figures.
Logging in is necessary to view these parameters.
•User-ID: «SERVICE»
•Password: without (in default state)
It is recommended to set a service password to prevent unintentional changes.
T6 Setting Max. Sensor Temperature

Installation Guide Linear Motors ENG
Page 18 / 47 P01-48-HP EX protected NTI AG / LinMot
T6 Setting Max. Winding Temperature
3.6.2 Higher-level temperature monitoring
The motors have an additional superior temperature monitoring by means of 2 Pt1000 temperature sensors,
which interrupts the power supply when the defined max. surface temperature is exceeded. The table below
must be consulted for setting the temperature relay.
Setting of Temperature Relais
Temperature class
Sensor
Max. surface temperature
T4
Pt1000
135 °C
T6
Pt1000
85 °C

Installation Guide Linear Motors ENG
NTI AG / LinMot P01-48-HP EX protected Page 19 / 47
3.7 Dimensions
3.7.1 PS01-48x150 with bearing PB01
in mm

Installation Guide Linear Motors ENG
Page 20 / 47 P01-48-HP EX protected NTI AG / LinMot
3.7.2 PS01-48x150 with bearing flange PB03
in mm