Lionel Rocket Launcher User manual

20229300250
11/22
Lionel
Rocket Launcher
Owner’s Manual
Lionel
Rocket Launcher
Owner’s Manual
This accessory features a launching rocket. Be sure to keep clear
of the rocket when it is on the launch pad. Children should be
supervised by an adult when operating this accessory.
Caution!

2
Thank You
Thank you for your purchase of the Lionel Rocket Launcher! Featuring a lighted motorized gantry that positions the rocket on the launching pad, this accessory allows you to relive
the early days of America’s space program. This classic accessory has been enhanced with
smoke, red flickering booster LEDs, and realistic sound effects with dialog for a more realistic
launch. It also features Plug-Expand-Play control and Command Control for use with a Lionel
CAB controller. Let the countdown begin!
This accessory features a launching rocket. Be sure to keep clear of the rocket
when it is on the launch pad. Children should be supervised by an adult when
operating this accessory.
•Base platform
•Lighted Motorized Gantry
•Rocket
•Plug-Expand-Play Controller
•Instruction Manual
Caution!
Rocket Launcher inventory of parts
Table of contents
Wiring your accessory to a Plug-Expand-Play lock-on 3
Adding smoke fluid to your Rocket Launcher 4
Connecting the Plug-Expand-Play controller to the Rocket Launcher 5
Installing your Rocket Launcher 5
Powering your Rocket Launcher 6
Legacy controller operations 6-7
TrainMaster Command Control (TMCC/Command Control) operations 8
Assigning your Rocket Launcher a new ID # 9
Operating your Rocket Launcher 9-10
LEGACY controller operations
The LEGACY CAB-2 Remote Controller 11
The Velocity Throttle 12
The Multi-Controller 12
The Train Brake Slider 12
The Warning Sound Controller 12
RailSounds sounds system 13
TrainMaster Command Control operations
CAB-1 Remote Controller commands 14
CAB-1 Remote Controller numeric keypad commands 14-15
Replacing the LEDs 15
Limited Warranty/Lionel Service 16

3
Wiring your accessory to a Plug-Expand-Play lock-on
Figure 1. Plug-Expand-Play wiring
Lock-on Power Block
Lock-on
3-pin male
connector
3-pin male
connector
3-pin male
connector
Plug-Expand-Play
Accessory
OR
Your Plug-Expand-Play accessory connects to either a Plug-Expand-Play lock-on (6-81313) or a Plug-Expand-Play power block lock-on (6-81314) with the 3-pin male connector that
is attached to its base. Simply plug this connector into the lock-on and apply track power. To
turn the accessory OFF, unplug the 3-pin connector from the lock-on or turn off the track
power. See figure 1 for wiring.
Auxiliary Power Supply
(optional)
The following Lionel marks are used throughout this Owner’s Manual and are protected under law. All rights
reserved.
Lionel®, FasTrack®, LEGACY®, LEGACY®Control System, Lockon®, TMCC®, CAB-1®Remote Controller, Plug-
Expand-Play®
e control box is required for operation of this accessory.
For Command Control, the Plug-Expand-Play ground must be connected to the
command base. For example, if an auxiliary power supply was used that the command
base isn't connected to, you wouldn't have command control of the Rocket Launcher.
Note!
Note!
Plug-Expand-Play
is revolutionary accessory system simplies the setup and operation of your
favorite accessories. Plug-Expand-Play accessories easily connect to your layout
for power using a standardized 3-pin cable that connects directly to a Plug-
Expand-Play Lock-on track section. ere are separate-sale cables that allow you
to expand your system to meet your needs.
TrainMaster Command Control
Devices equipped with the classic TrainMaster® Command Control system are
controlled by commands from your CAB-1 or CAB-2 Remote Controller. Motion,
basic sounds, and other control actions are all at your ngertips as you walk
around your layout.

4
Adding smoke fluid to your Rocket Launcher
Before you operate your Rocket Launcher, be sure to add smoke fluid to the smoke unit. Never operate this accessory without smoke fluid. To add the fluid, squeeze the sides and
lift up the block house as illustrated in Figure 2. Remove the small plug and add 8-10 drops of
smoke fluid. Add several more drops as smoke production decreases.
Never operate this accessory without smoke fluid to avoid damage to the smoke
unit.
Caution!
SMOKE
OFF
ON
PROG
VOLUME
KNOB
RUN
Figure 2. Smoke unit location
Plug
ADD SMOKE
FLUID HERE
Fan. DO NOT ADD SMOKE
FLUID HERE!
Volume knob
Program/
Run switch
Smoke unit
switch
FRONT
REAR

5
Connecting the Plug-Expand-Play controller to the Rocket Launcher
Installing your Rocket Launcher
Set up your controller to operate the Rocket Launcher's gantry crane and begin the countdown. As illustrated in Figure 3, simply connect the Plug-Expand-Play controller
with the plugs on the wires.
The plugs are “keyed” to fit together only one way.
Place the Rocket Launcher on your layout. Choose a location that is approximately 16”
x 10”. Next, position the gantry crane on its track
so that the post in the platform is inserted into
the slot at the base of the gantry. Be sure that the
side of the gantry with the rounded openings in
the platform faces the launch pad.
Set up the derrick at the top of the gantry.
Carefully raise the mast until it snaps into place.
It should now be in a vertical position as
illustrated in Figure 5. To lower the mast, gently
bend the mast lock away from the base to pull
the locking pin out, but be careful not to bend
the mast lock excessively. Finally, check that the
winch lines are properly threaded through the
pulleys.
To avoid damaging your mast, do not
raise it beyond its vertical position.
Note!
Figure 3. Controller connection
Figure 4. Gantry positioning
Figure 5. Derrick set up
Note!

6
1. Turn off track power, and then plug in the LEGACY Base and connect it to the track.
2. Plug your Rocket Launcher into a Plug-Expand-Play Lock-on. If the Lock-on has a
power switch, make sure it is on.
3. Increase track power voltage to full power (no more than 19 volts AC). If a circuit
breaker trips when you turn on the Lionel power supply, make sure the track is free of all metals
that may cause a short circuit.
4. As illustrated in Figure 6, press ENG and 1 (or your selected ENG ID#) to address the
locomotive with your LEGACY CAB-2 Remote Controller.
Figure 6. LEGACY engine selection
LEGACY controller operations
Your Rocket Launcher is compatible for operation with the Lionel LEGACY system. It will also operate on the original Lionel TrainMaster System (TMCC1) and also on the LEGACY Cab-1L /
Base-1L operating system.
Your commands are sent by the Remote Controller to the Command Base, which broadcasts a
radio frequency that is distributed through the outer rails of the track to your accessory. Your
accessory will not respond until it recognizes its unique ID#, so you can operate multiple Command-
equipped accessories on the same track at the same time.
Powering your Rocket Launcher
Your Rocket Launcher is designed to work with either AC or DC power.
AC Power: Use an alternating-current (50-60Hz AC) transformer for Legacy, Command Control,
Bluetooth, or Conventional control. Powering your accessory in excess of 19 volts AC may result in
damage to sensitive electronic components.
DC Power: Use a DC transformer for Plug-Expand-Play control only. Your accessory is NOT
designed to operate with Command Control while using DC power. Powering your accessory in
excess of 19 volts DC may result in damage to sensitive electronic components.
Due to technical dierences, we recommend using CAB1 mode with the Cab2 controller
for optimum Command Control operation. e original Cab1 and Cab1-L also work very
well with this accessory.
Note!

7
5. After selecting the ENG ID# on the Cab 2 remote, your remote needs to be configured
for TMCC or CAB1 control for the accessory. Select the ID# of your accessory as before,
then press the INFO button on the top right of your CAB-2 remote.
Press the SCROLL button on the top left of the CAB-2 row until the CONTROL tab is selected.
Press the button that corresponds to the TMCC or CAB1 (preferred) Mode selection on the
screen.
6. Press the SCROLL button once more to select the SOUND tab. Press the button that corresponds
to RS5 to enable RailSounds 5 Mode. This will also enable the icons on the keypad for a more
user-friendly experience. Congratulations! You have now configured your CAB-2 remote to run
your accessory in CAB1 (preferred) or TMCC mode. Enjoy all the features your locomotive has to
offer.
7. Press the Start Up key on your LEGACY CAB-2 Remote, shown in Figure 9. Then, let
the countdown begin! Your rocket launcher's sound will start up, and the accessory-specific
touch screen buttons will populate the remote. For more information on operating your accessory
with the LEGACY system, please refer to the LEGACY section of this manual. Additional
information is also found in the LEGACY System Manual, available online at
www.lionel.com.
LEGACY Control operations continued
Figure 9. LEGACY start-up
Figure 7. CAB-2 info button
Figure 8a. CAB-2 scroll button Figure 8b. CAB-2 control screen
ENGINE 1 INFO
Custom
Type
OTH TMCC
CAB1
TMCC
LE
G

LRS
Control
Sound

8
TrainMaster Command Control (TMCC/Command Control) operations
For operation in the TrainMaster Command Control environment, you need a TrainMaster Command Base (6-12911) and a CAB-1 Remote Controller (6-12868). Refer to your TMCC
System Manual for complete information.
Your commands are sent by the CAB-1 Remote Controller to the Command Base, which
translates the command into digital code. That code is sent through the outside rails to your
accessory, which will not respond until it recognizes its unique ID#. TrainMaster Command Control
gives you the power to operate multiple Command-equipped accessories on the same layout at the
same time.
1. Turn off track power, and then plug in the Command Base and connect it to the
track.
2. Plug your Rocket Launcher into a Plug-Expand-Play Lock-on. If the lock-on has a
power switch, make sure it is on.
3. Increase track voltage to full power (no more than 19 volts AC). If a circuit breaker trips
when you turn on the Lionel power supply, check to make sure the track is free of all metals that
may cause a short circuit.
4. Press ENG and the programmed ID to address your Rocket Launcher with your
CAB-1 Remote Controller.
5. Let the countdown begin!

9
For operation in the Command Control environment, you will want to give your Rocket Launcher a unique ID#. Your accessory will respond to commands associated with its ID# while all other
accessories will disregard these commands. This procedure is not necessary for Plug-Expand-
Play operation.
1. Slide the program run switch on the smoke generator cover to the PROG position.
See Figure 2 on page 4.
2. Plug the launcher into a Plug-Expand-Play lock-on.
3. Connect the Command Base and plug it in.
4. Power up the track.
5. Press ENG on the CAB-1 or CAB-2 remote.
6. Enter the unique ID#. Choose any number from 1 to 98 that has not been assigned
to another locomotive or accessory (ENG).
All Command Control enabled locomotives respond to ENG 99. We recommend that you
reserve ID# 99 as a "universal" ID#.
7. Press SET. The launcher will emit a beep sound.
8. Slide the program run switch back to the RUN position.
The Rocket Launcher's ID# has been set. Be sure to record the new ID# for your
reference.
Assigning your Rocket Launcher a new ID#
Note!
Operating the Rocket Launcher
All systems are “Go” for launch! Complete these final preparations, then start the countdown.
To prevent damage to the smoke unit, do not operate the Rocket Launcher
without smoke fluid or turn the smoke unit OFF.
Caution!
Figure 10. Arming launcher
1. Suspend the rocket from the crane’s magnet and press
the launching mechanism down until it locks as
illustrated in Figure 10.
2. Maneuver the gantry toward the rocket platform using
the GANTRY lever on the PEP controller or by using
the red throttle knob on the CAB1 / CAB1-L or CAB2
controllers. Key 3 and Key 6 of the CAB controllers
also control forward / reverse gantry movement.

10
3. Once the rocket is in position, stop the gantry
movement by releasing the lever (PEP control)
or by using the red knob, reset (Key 0) or the
DIR change button (CAB controllers). Or
simply wait for the limit switch to stop
movement.
4. Turn the cranks to lower the rocket onto the
launch pad, then move the gantry back. To
identify the cranks, refer to Figure 12.
If the gantry is at the forward limit
switch when a launch is begun, it
will automatically be retracted to
the rear limit switch location.
Crank 1 will raise and lower the magnet.
Crank 2 will raise and lower the boom.
5. Start the countdown by pressing the Launch
button on the PEP controller, or by pressing
and holding Aux1 for more than 3 seconds on
the CAB1, CAB1-L or CAB2 controllers.
Press and hold the Launch button
on the Plug-Expand-Play control
box to shutdown launcher. Press &
hold while shutdown to start in
T-Minus 15 Mode (short launch).
Note!
Note!
Caution!
REVERSE
GANTRY
FORWARD
SMOKE OFF
SMOKE ONLAUNCH
Figure 11. Plug-Expand-Play control box
Figure 12. Derrick cranks
Crank 2
Raises and
lowers the boom
Crank 1
Raises and lowers
the magnet
Operating the Rocket Launcher continued
Press the Launch button (PEP controller) if you wish to abort the launch during the launch
sequence. The red triangular button or the Key 0 (Reset) can be used to abort a launch if
using one of the CAB remotes.
Keep clear of the rocket during launch to avoid injury.
6. Get ready for another launch! Repeat the steps above.