Lippert Components Solera 728810 Installation instructions

1
lci1.com 574-537-8900 Rev: 02.06.20
Solera®Anti-
Billowing Device
Installation and Owner’s Manual
(For Aftermarket Applications)
CCD-0001299
Table of Contents
Parts List ................................................ 2
Introduction ............................................ 2
Safety ................................................... 2
Resources Required ................................... 3
Installation .............................................. 3
Solera®Anti-
Billowing Device
Installation and
Owner’s Manual
(For Aftermarket Applications)
Solera Anti-Billowing Device Aftermarket Kits
Part# Description
728810 Solera Anti-Billowing Device - Black
728811 Solera Anti-Billowing Device - White

2
lci1.com 574-537-8900 Rev: 02.06.20
Solera®Anti-
Billowing Device
Installation and Owner’s Manual
(For Aftermarket Applications)
CCD-0001299
Introduction
The Solera®Anti-Billowing Device is designed for use with
Solera®Slider Awnings in order to prevent billowing of
the awning while it is in the retracted position. This device
installs onto the end cap of the roll tube and the side of
the unit and physically stops the awning from extending or
billowing due to wind.
MOVING PARTS CAN PINCH, CRUSH OR CUT. KEEP
CLEAR AND USE CAUTION.
FAILURE TO SUPPORT AND MAINTAIN CONTROL OF
THE ROLL TUBE, FABRIC AND DRIVE/IDLER HEAD
ASSEMBLIES DURING INSTALLATION PROCEDURE
MAY RESULT IN PERSONAL INJURY OR PRODUCT
OR PROPERTY DAMAGE.
Parts List
Letter Part# Description Qty
A
717772 
Spacing, Black 1
717773 
Spacing, White
B
717766 Stop; Anti-Billow, Slide Topper, Black
1
717767 Stop; Anti-Billow, Slide Topper, White
C
276611 
Black 3
675906 
D
364290 
 2
252593 

A
B
D
C
AN UNSTABLE, ROLLING UNIT CAN CREATE AN
UNSAFE CONDITION THAT MAY RESULT IN
PRODUCT OR PROPERTY DAMAGE OR PERSONAL
INJURY. CHOCK TIRES BEFORE PERFORMING
SERVICE TO PREVENT POSSIBLE PRODUCT OR
PROPERTY DAMAGE OR PERSONAL INJURY.
NOTE: 


Additional information about this product can be obtained
from lci1.com/support
app. The app is available on iTunes®®®
™for Android™users.
iTunes ®®®are registered trademarks of

™and Android™
Safety
Read and understand all instructions before installing
or operating this product. Adhere to all safety labels.
This manual provides general instructions. Many variables
can change the circumstances of the instructions, i.e.,
󰀩
individual performing the instructions. This manual
cannot begin to plot out instructions for every possibility,
but provides the general instructions, as necessary, for
󰀨

result in death, serious personal injury, severe product

limited warranty.

3
lci1.com 574-537-8900 Rev: 02.06.20
Solera®Anti-
Billowing Device
Installation and Owner’s Manual
(For Aftermarket Applications)
CCD-0001299
Installation
The Anti-Billowing Device should be installed on the end of
the awning that is closest to the front of the unit.
1. Make sure awning is fully retracted.
2. (Fig.1A) on the end cap of the roll tube of
the awning so that the stop is pointing upwards in the 12
o’clock position (Fig.1).
3. Use a #2 square drive bit to install three #8-18 x ½”
square pan head self-drilling screws through the mounting
holes (Fig.1B) and into the end cap.
4. With the slide-out still fully retracted, hold the bracket
(Fig.1C) against the outside of the unit so the primary
surface of the bracket (Fig.1D) is in line with the middle of
the awning’s roll tube (Fig.1E).
5. While holding the stop in place, hand turn the roll tube
towards the bracket to make sure that the roll tube and
stop do not contact the bracket until the end of the stop
rests on the bracket. Then, extend the slide-out to make

made, readjust as needed.
6. 
location of the bracket with a grease pen.
7. Extend the awning to allow enough clearance for the use
of a cordless drill or screw gun. Apply a liberal amount of
sealant to the back of the bracket, then place the bracket in
the marked location (step 6). Using a cordless drill or screw
gun with a #2 drive bit, install two #8-18 x 1” square pan
head self-drilling screws (Fig.2A) to secure the bracket to
the outside surface of the unit’s wall.
NOTE: When awning is extended, the stop (Fig.2B) may not

8. Extend and fully retract the slide-out and awning a few
times to verify proper installation.
A
C
B
D
E
Fig.1
A
B
Fig.2
Resources Required
• Cordless or electric drill or screw gun
• #2 square drive bits
• Sealant
• Grease pen

4
lci1.com 574-537-8900 Rev: 02.06.20
Solera®Anti-
Billowing Device
Installation and Owner’s Manual
(For Aftermarket Applications)
CCD-0001299
Manual information may be distributed as a complete

explicit consent to distribute individual parts.
All manual information is subject to change without
notice. Revised editions will be available for free
download at lci1.com. Manual information is considered
factual until made obsolete by a revised version.


Notes