Litex JP13EB6CRS User manual

E192641
LISTED
For
Damp Location
FIELDER CEILING FAN
ITEM #0708569
MODEL #JP13EB6CRS
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-527-1292, 8:30 a.m. - 5 p.m., CST, Monday - Friday.
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
1
Español p. 18

READ AND SAVE THESE INSTRUCTIONS
TABLE OF CONTENTS
2
SAFETY INFORMATION
• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for
repairs, it must be shipped in its original packaging to ensure proper protection against damage
that might exceed the initial cause for return.
• Make sure that all electrical connections comply with local codes, ordinances, the National
Electrical Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself
wiring handbook (available at Lowe's) if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 10 ft. from the blades to
the floor and at least 30 in. from the end of the blades to any obstruction.
• After you install the fan, make sure that all connections are secure to prevent the fan from falling.
• The net weight of this fan including the light kit is: 24.95 lbs.
Safety Information .................................................................................................................2
Package Contents .................................................................................................................4
Hardware Contents ...............................................................................................................5
Preparation ...........................................................................................................................5
Initial Installation ...................................................................................................................6
Fan Mounting ......................................................................................................................
. .7
Wiring ..........................................................................................................................
. ...... . 10
Final Installation ..................................................................................................................11
Installing Fan Without Light Kit ....................................................
. ................................... . . . .13
Automated Learning Process/Activating Code ...................................................................14
Operating Instructions For Remote Control and Fan...........................................................15
Care and Maintenance ...............................................................................
. ................... . ....16
Troubleshooting...................................................................................................................16
Limited Lifetime Warranty ..................................................................................................17
Replacement Parts List ...................................................................................................
. . . .17

SAFETY INFORMATION
To reduce the risk of fire, electrical shock, or personal injury, mount fan to outlet box
marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS. (15.9 KG) OR LESS" and use
mounting screws provided with the outlet box. Most outlet boxes commonly used for the
support of lighting fixtures are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box. Secure the outlet
box directly to the building structure. The outlet box and its support must be able to support the
moving weight of the fan (at least 35 lbs.). Do NOT use a plastic outlet box.
To avoid personal injury, the use of gloves may be necessary while handling fan parts with
sharp edges.
To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with this
fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your
house wire is larger than 12-gauge or there is more than one house wire to connect to the
corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.
To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed control
device or control fan speed with a full range dimmer switch.
To reduce the risk of fire, electrical shock, or personal injury, do not bend the blade arms when
installing them, balancing the blades, or cleaning the fan. Do not insert objects between the
rotating fan blades.
To reduce the risk of personal injury, use only parts provided with this fan. The use of parts
OTHER than those provided with this fan will void the warranty.
This fan MUST be installed with the safety cable provided with the fan. Failure to use the
safety cable provided may result in personal injury, damage to the fan or damage to other
property.
WARNING
CAUTION
Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid
electrical shock.
Read all instructions and safety information before installing your new fan. Review the
accompanying assembly diagrams.
3
DANGER
If using this fan in a DAMP location, this fan must be connected to a supply circuit that is protected
by a Ground Fault Circuit Interrupter (GFCI) to reduce the risk of personal injury, electrical shock
or death.

4
PACKAGE CONTENTS
IMPORTANT REMINDER: You must use the
parts provided with this fan for proper installation
and safety.
A Downrod 1
B Canopy 1
C Mounting Bracket 1
D Motor Assembly 1
E Pin (preassembled) 1
F Clip (preassembled) 1
G Canopy Mounting Screw 2
(preassembled)
H Canopy Cover 1
I Remote Control 1
Transmitter
J Remote Control Receiver 1
K Battery 1
DESCRIPTIONPART QUANTITY L Yoke Cover 1
M Safety Cable 1
(preassembled)
N Motor Plate Screw 3
(preassembled)
O Light Kit Fitter Plate 1
P Light Kit Fitter Plate Screw 3
(preassembled)
Q Light Kit Fitter 1
(preassembled)
R Bulb 2
S Glass Shade 1
T Fitter Plate 1
U Fitter Plate Cover 1
DESCRIPTIONPART QUANTITY
FE
A
D
B
C
G
H
I
J
K
L
M
O
Q
S
P
R
T
U
N

5
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware cantents list. If any part is missing or damaged, do not attempt to
assemble the product.
Estimated Assembly Time: 120 minutes
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety
Glasses, Stepladder and Wire Strippers
Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself Wiring Handbook and
Wire Cutters
DANGER: When using an existing outlet box, make sure the outlet box is securely attached to
the building structure and can support the full weight of the fan. Failure to do this can result in serious
injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan
after installation is complete.
CAUTION: Be sure outlet box is properly grounded and that a ground wire (green or bare) is
present.
After opening top of carton, remove mounting hardware package from foam inserts. Remove motor
from packing and place on carpet or on foam to avoid damage to finish.
CAUTION: Carefully check all screws, bolts and nuts on fan motor assembly to ensure that they
are secured.
PREPARATION
HARDWARE CONTENTS (shown actual size)
AA
E3 Wire
Connector
Qty. 10

Turn off circuit breakers and wall switch to the fan
supply line leads.
DANGER: Failure to disconnect power supply
prior to installation may result in serious injury or
death.
1.
Check to make sure outermost edge of small fans
will be at least 30 in. from any obstruction. Check
downrod (A) length to ensure blades will be at least
10 ft. above the floor when smaller fans are in fully
tilted position.
3.
6
ON
OFF
ON
OFF
3
1
This fan can only be mounted with the downrod in
the motor assembly (D).
NOTE: Angle mount or closemount configurations
are not available for this fan.
2. 2
10 ft
min.
30 in.
min.
INITIAL INSTALLATION
D
A

Remove pin (E) and clip (F) from yoke at top of
motor assembly (D) and partially loosen
preassembled set screws.
*Helpful Hint: Downrod-style mounting is best
suited for ceilings 8 ft. (2.44 m) high or higher. For
taller ceilings you may want to use a longer downrod
(not included) than the one provided. A longer
downrod is sometimes necessary to ensure proper
blade clearance.
1.
Secure mounting bracket (C) to outlet box (not
included) using screws, spring washers, and flat
washers provided with the outlet box.
*NOTE: It is very important that you use the
proper hardware when installing the mounting
bracket (C) as this will support the fan.
4. 4
INITIAL INSTALLATION
FAN MOUNTING
7
C
Set Screw
D
E
F
1

FAN MOUNTING
Depending on the length of downrod (A) you
use, you may need to cut the lead wires back to
simplify the wiring. If you decide to cut back the
lead wires, it is suggested that you do so in the
following manner:
Take the lead wires and make sure that you
have pulled them all the way through the top of
the downrod (A). Start at the TOP of the
downrod (A) and measure 8 in. of lead wire, and
then cut the excess wire off with wire cutters (not
included).
NOTE: If you do not cut back the lead wires,
Steps 4 and 5 are not necessary and you may
proceed to Step 6 instead.
4.
2. Insert downrod (A) through canopy (B), canopy
cover (H) and yoke cover (L). [NOTE: Canopy
cover (H) must be turned with the shiny side
toward the motor assembly (D).] Thread wires
from motor assembly (D) through downrod (A).
3.
4
A
8
Set
Screw
F
A
E
3
D
2
A
B
L
H
L
H
Slip downrod (A) into yoke at top of motor
assembly (D), align holes and re-install pin (E)
and clip (F). Re-tighten set screws in yoke and
then tighten nuts. Slide yoke cover (L) down until
it rests on top of motor assembly (D).

9
Slide downrod (A) through opening in mounting
bracket (C) and then turn the downrod (A) so the
straight edges at the top of the downrod (A) align
with the sides of the mounting bracket (C). Pull
down firmly on the downrod (A) until it sits securely
inside the mounting bracket (C).
DANGER: Failure to secure downrod (A) in
mounting bracket (C) may result in serious injury or
death.
IMPORTANT: Due to the size (width) of this fan, it
is advisable to seek the help of another person to
hold the stepladder in place and to then help lift the
fan up to you once you are set on the ladder.
6.
If you decided to cut back the lead wires in Step 4,
strip a 1/2 in. of insulation from end of white wire.
Twist stripped ends of each strand of wire within
the insulation with pliers (not included). Repeat
Step 5 for black, blue (if applicable) and green
wires.
5.
FAN MOUNTING
5
6
A
C
Find a secure attachment point (wood ceiling joist
recommended) and secure safety cable. Use a
heavy-duty wood screw, washer and lock washer
(all not included) to secure safety cable (M) loop.If
necessary, adjust the loop at the end of the safety
cable. The loop at the end of the safety cable (M)
should just fit over the threads on the wood screw.
Extra cable slack can be left in ceiling area.
7. 7
Loop
Wood Joist
Wood Screw
and Washers
M

WIRING
10
Wrap electrical tape (not included) around each
individual wire connector (AA) down to the wire.
WARNING: Make sure no bare wire or wire
strands are visible after making connections. Place
green and white connections on opposite side of
box from the black connections.
Turn spliced/taped wires upward and gently push
wires and wire connectors (AA) into outlet box.
2. 2
1. 1
AA
AA AA
WHITE SUPPLY WIRE
BLACK SUPPLY WIRE
BLACK
BLACK
WHITE
BLUE
BLUE
WHITE
BLACK
AC IN L
AC IN N
WHITE
WHITE
GROUND (GREEN
OR BARE)
FROM FAN
FROM RECEIVER
ANTENNA
FROM
CEILING
BLACK
FROM RECEIVER
Make the necessary wiring connections for remote
control operation according to Fig. 1. For each wire
connection, use one of the wire connectors (AA)
provided, making sure to screw wire connector (AA)
on in a clockwise direction. [Make sure to connect
all GROUND (GREEN) wires together from fan (on
downrod (A) and mounting bracket C)) to
BARE/GREEN wire from ceiling.]
WIRING TIP: Wiring your fan's remote control
requires extreme patience. Take mandatory breaks
while wiring to allow your arms to rest.
Hardware Used
E3 Wire Connector x 6
AA
J
CAUTION: Be sure outlet box is properly grounded and that a ground (green or bare) wire is
present.
WARNING: If house wires are different colors than referred to in the following steps, stop
immediately. A professional electrician is recommended to determine wiring.
DANGER: If using this fan in a DAMP location, this fan must be connected to a supply circuit that
is protected by a Ground Fault Circuit Interrupter (GFCI) to reduce the risk of personal injury,
electrical shock or death.
WARNING: To reduce the risk of fire, electrical shock, or personal injury, wire connectors
provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from
the fan. If your house wire is larger than 12-gauge or there is more than one house wire to connect to
the corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.
NOTE: Black and blue wires are hot power for fan. White wire is common for fan. Green or bare wire
is ground.
NOTE: Please refer to installation and operating instructions for remote control.

WIRING
11
3
Gently slide remote control receiver (J) smooth side
up into mounting bracket (C). Turn spliced/taped
wires upward and gently push wires and wire
connectors (AA) into outlet box. Let antenna from
remote control receiver (J) hang to the side.
NOTE: The remote control included with this fan
meets the following requirements:
a. Not for use with solid state fans.
b. Electrical rating: 120V / 60 Hz;
motor amps:1.5 MAX.
Should you choose to use a different remote control
with this fan, it must also meet these same
requirements
3.
Antenna
A
J
C
1.
FINAL INSTALLATION
Locate two canopy mounting screws (G) on
underside of mounting bracket (C) and remove
canopy mounting screw (G) closest to the open end
of the mounting bracket (C). Partially loosen the
other canopy mounting screw (G). Lift canopy (B)
to mounting bracket (C). Place rounded part of
slotted hole in canopy (B) over loosened canopy
mounting screw (G) in mounting bracket (C) and
push up. Twist canopy (B) to lock. Re-insert canopy
mounting screw (G) that was removed, and then
tighten both canopy mounting screws (G) securely.
Slide canopy cover (H) up to canopy (B), aligning
rounded part of slotted holes in canopy cover (H)
with screwheads in bottom of canopy (B). Turn
canopy cover (H) to the right (clockwise) until it
stops.
If you do NOT wish to use the light kit, skip to
section titled INSTALLING FAN WITHOUT LIGHT
KIT on page 13.
If you DO you wish to use the light kit, proceed
to Step 2.
1
H
B
G

12
Remove light kit fitter plate screw (P) located in the
non-slotted hole in light kit fitter (Q) and partially
loosen the other two light kit fitter plate screws (P).
CAUTION: Do NOT remove screws on light kit
fitter (Q) that have washers; these are not the light
kit fitter plate screws (P).
Twist light kit fitter (Q) counterclockwise to remove it
from the inside of the light kit fitter plate (O).
2. 2
FINAL INSTALLATION
Q
P
O
P
Remove one motor plate screw (N) from motor plate
on underside of motor assembly (D) and partially
loosen the other two motor plate screws (N). Feed
molex connections from motor assembly (D)
through the middle of light kit fitter plate (O). Then,
align the slotted holes in the center of light kit fitter
plate (O) with loosened motor plate screws (N),
twisting it clockwise until it locks. Re-insert motor
plate screw (N) previously removed and securely
tighten all three motor plate screws (N).
3.
Molex
Connections
Motor Plate
3D
O
N
Molex
Connections
4. Connect the molex connections from the motor
assembly (D) to those from the light kit fitter (Q) --
black to black and white to white. Make sure they
are secure.
Align slotted holes in light kit fitter (Q) with loosened
light kit fitter plate screws (P), then twist it clockwise
until it locks. Re-insert light kit fitter plate screw (P)
previously removed (Step 2, page 12) and tighten all
three light kit fitter plate screws (P) securely.
4
Q
P
D
Molex
Connections

13
FINAL INSTALLATION
5. Install bulbs (R).
WARNING: When you need to replace bulb(s),
please allow the bulb(s) and glass shade to cool
down before touching them.
5
RR
6. Align slots on glass shade (S) with nodules on the
inside of the light kit fitter (Q). Turn glass shade (S)
clockwise until it no longer turns.
NOTE: Pull down gently on the glass shade (S) to
make sure it is secured completely.
Assembly is now complete.
S
Q
6
Slot
Nodule
(on inside)
Motor Plate
D
INSTALLING FAN WITHOUT LIGHT KIT
1. To install the fan without the light kit, remove one
motor plate screw (N) from motor plate on underside
of motor assembly (D) and partially loosen the other
two motor plate screws (N). Align slotted holes in
fitter plate (T) with loosened motor plate screws (N),
then twist it clockwise until it locks. Re-insert motor
plate screw (N) previously removed and securely
tighten all three motor plate screws (N).
1
N
T

14
AUTOMATED LEARNING PROCESS/ACTIVATING CODE
Remove battery cover from back side of remote
control transmitter (I).
Install the 12-volt battery (K) and then replace
battery cover on remote control transmitter (I).
1.
(back side)
CAUTION: The remote control transmitter (I) can be programmed to multiple receivers or fans. If
this is not desired, turn wall switch off to any other programmable receiver or fan.
1
Code Switches
Battery
Cover
I
K
2. 2
Align hole on the inside of the fitter plate cover
(U) with the threaded rod on the fitter plate (T).
Secure fitter plate cover (U) by turning fitter plate
cover (U) clockwise until it no longer turns.
U
TThreaded
Rod
Assembly is now complete.
INSTALLING FAN WITHOUT LIGHT KIT
2. Restore electrical power. Within 30 seconds of
restoring electrical power, press the “OFF” button
on the front of the remote control transmitter (I)
for 5 seconds or until light on fan blinks twice.
Use the remote control to test the oscillation, fan
and light functions (see operating instructions
below) to confirm the learning process is
complete.
IMPORTANT: To prevent damage to remote
control transmitter (I), remove the battery (K) if
not used for long periods. Store the remote
control transmitter (I) away from excess heat.
2
(front)
I

OPERATING INSTRUCTIONS FOR REMOTE CONTROL AND FAN
Modifications not approved by the party responsible for compliance could void the user's authority to
operate the equipment.
*NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
AUTOMATED LEARNING PROCESS/ACTIVATING CODE
The tilt angle of the smaller fans may be adjusted up or
down by simply manually moving them gently up or
down.
CAUTION: To avoid personal injury or damage to
the fan(s), both the main fan and the smaller fans
MUST BE OFF before adjusting the smaller fans up
or down.
2. 2
smaller fan smaller fan
main fan
Operation buttons on the panel of the remote control
transmitter (I) :
Button turns the 2 smaller fans to HIGH
speed
Button turns the 2 smaller fans to MEDIUM
speed
Button turns the 2 smaller fans to LOW
speed
Button turns the 2 smaller fans OFF
Button turns main fan ON/OFF when pressed
once (i.e., controls rotation of the entire
fan)
Button turns light ON/OFF when pressed
once; If you press button in excess of
0.7 seconds, it becomes a dimmer.
1. 1
I
15

TROUBLESHOOTING
At least twice each year, lower canopy (B) to check downrod (A) assembly, and then tighten all screws
on the fan. Clean motor assembly (D) with only a soft brush or lint-free cloth to avoid scratching the
finish. Clean blades in smaller fans with a lint-free cloth.
IMPORTANT: Shut off main power supply before beginning any maintenance. Do not use water or a
damp cloth to clean the ceiling fan.
CARE AND MAINTENANCE
WARNING: Before beginning work, shut off the power supply to avoid electrical shock.
16
NOTE: A small amount of "wobble" is normal and should not be considered a defect.
Fan and light (if
applicable) fail to
operate with remote
control.
1. Learning process was not done correctly
and code was not activated.
2. Battery in remote control transmitter is no
longer good
1. Turn power off and repeat Step 2 on
page 16.
2. Check battery in transmitter and replace
battery if necessary.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Fan does not move. 1. Power is off or circuit breaker in electrical
box trips.
2. Faulty wire connection.
3. Learning code process between fan and
remote control transmitter may not have
been successful and learning code was
not activated.
1. Turn power on or check circuit breaker.
2. Turn power off. Loosen canopy and
check all connections.
3. Turn off power and repeat instructions in
Step 2 on page 16.
Excessive wobbling. 1. Fan not securely mounted.
2. Set screw(s) on motor housing yoke is
(are) not tightened properly.
3. Set screw on hanging ball is not tightened
properly.
1. Turn power off. Carefully loosen canopy
and verify that mounting bracket is
secure.
2. Tighten yoke set screw(s) securely.
3. Carefully loosen and lower canopy and
verify that set screw on hanging ball is
tightened securely.
Noisy operation. 1. Full range dimmer switch.
2. Fan is new. 1. Use only remote control provided with
fan.
2. Allow fan a “break in” period of a few
days, especially when running the fan at
Medium and High speeds.
Fan operates but
light fails. 1. Bulb(s) not installed correctly. 2. Wires in canopy not wired properly.
3. Wires in light kit fitter not wired correctly.
4. Light kit is lamped with more than the
allowable 190W, causing the wattage
limiting device to interrupt the flow of
electricity to the light kit.
1. Re-install bulb(s).
2. Check wires in canopy and, if necessary,
re-wire according to instructions on
page 10.
3. Check that the molex connections in the
light kit fitter are connected properly
according to instructions on page 13.
4. Lamp light kit with bulbs that total no
more than 190W.

LITEX LIFETIME LIMITED WARRANTY:
LITEX INDUSTRIES, LTD. warrants this fan to the original household purchaser for indoor use under
the following provisions:
1-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will replace or repair any fan which has faulty
performance due to a defect in material or workmanship. Contact Customer Service at
1-800-527-1292 to arrange for return of fan. Return fan, shipping prepaid, to Litex Industries, Ltd. We
will repair or ship you a replacement fan, and we will pay the return shipping cost.
5-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will repair or replace, at no charge to the original
purchaser, any fan motor that fails to operate satisfactorily when failure results from normal use.
RETURN FAN MOTOR ONLY, shipping prepaid, to Litex Industries. We will repair or ship purchaser a
replacement motor and Litex will pay the return shipping cost.
6-YEAR to LIFETIME LIMITED WARRANTY: LITEX INDUSTRIES, LTD. will repair the fan, at no
charge to the original purchaser for labor only, if the fan motor fails to operate satisfactorily when
failure results from normal use. Parts used in the repair will be billed to the purchaser at prevailing
prices at time of repair.
The purchaser shall be responsible for all costs incurred in the removal, reinstallation and shipping of
the product for repairs.
This warranty does not apply when damage from mechanical, physical, electrical or water abuse
results in causing the malfunction. Deterioration of finishes or other parts due to time or exposure to
salt air is specifically exempted under this warranty.
Neither Litex Industries nor the manufacturer will assume any liability resulting from improper
installation or use of this product. In no case shall the company be liable for any consequential
damages for breach of this, or any other warranty expressed or implied whatsoever. This limitation as
to consequential damages shall not apply in states where prohibited.
ABC
PART DESCRIPTION
A Downrod
B Canopy
C Mounting Bracket
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-800-527-1292, 8:30 a.m. - 5 p.m.,
CST, Monday - Friday.
WARRANTY
17