Little Cottage Octagon Installation guide

LITTLE COTTAGE CO.
PO Box 455, Berlin, OH 44610 • 330-893-4212 • www.cottagekits.com
Octagon Greenhouse
AssEmbLy InsTruCTIOn
mAnuAL
© 2019 Little Cottage Co.
- Cordless Drill (12V or higher)
- #2 Square Drive Bit
- Hammer
8x8 Octagon Greenhouse
Tools Needed:
Size: 8’x8’
Rear View
- Tape Measure
- Utility Knife With Blade &
Hook Blade
- Speed Square
- 5/16” Wood Drill bit
All manuals and user guides at all-guides.com
all-guides.com

Octagon Greenhouse
AssEmbLy InsTruCTIOn mAnuAL
2
© 2019 Little Cottage Co.
Assembly Instruction Manual
1. Locate 4x4 runners for 8x8 Octagon Green-
house. Layout 4x4’s as shown.
2. Next locate the 8 pieces of rim and joist.
3. Here you see the 8 pieces of rim. 4. The rims are numbered as shown. Make sure
matching numbers are connected.
5. Continue with rim and make sure all numbers
match.
6. Next secure rim with 2 1/2” Zinc screws as
shown. Make sure all points are ush as shown.
All manuals and user guides at all-guides.com

Octagon Greenhouse
AssEmbLy InsTruCTIOn mAnuAL
3
© 2019 Little Cottage Co.
Assembly Instruction Manual
7. Next layout the oor joist. 8. The rims are also marked off where the joist
need to go. Secure joist with 2 1/2” Zinc screws.
9. Next check oor framing for square as shown. 10. Next place oor on top of 4x4’s as shown.
11. The 2 longest 4x4’s need to be in the center.
Keep 4x4 ush with rim and secure with 2 1/2”
Zinc Screws as shown.
12. Next place shorter 4x4’s as shown. Next pic-
ture will be more detailed.
All manuals and user guides at all-guides.com

Octagon Greenhouse
AssEmbLy InsTruCTIOn mAnuAL
4
© 2019 Little Cottage Co.
Assembly Instruction Manual
13. Hang tape over 4x4 and measure to corner of
rim. Both reveels need to be the same.
14. Secure all corners of 4x4s with 2 1/2”
Screws. Next measure oor for square as shown.
15. Once oor is square secure all the joist to the
4x4 runners as shown. Angle 2 1/2” screws thru
joist into 4x4 runner. One on each side.
16. Next locate 5/8” plywood ooring.
17. The plywood is all cut. You may have to lay
the ooring out before you fasten anything to
make sure the pieces are placed properly.
18. Next secure plywood to joint and rim as
shown using 1 1/4” Zinc Screws.
All manuals and user guides at all-guides.com

Octagon Greenhouse
AssEmbLy InsTruCTIOn mAnuAL
5
© 2019 Little Cottage Co.
Assembly Instruction Manual
19. Continue with fastening oor. Secure 1 1/4”
screw every 8” to 10”.
20. Securing the last piece of ooring.
21. Next locate wall panels. 22. Start with panel A and continue thru panel H.
23. Secure wall panel A with 2 1/2” screws as
shown. make sure corners line up and put pres-
sure on the outside pushing in so wall is tight
against oor as shown.
24. Repeat on opposite end.
All manuals and user guides at all-guides.com