Little Tikes T-Rex Truck User manual

ASSEMBLY INSTRUCTIONS
T-Rex Truck
XIM656705-R2 - 3/21
1
Adult assembly required. Approx. assembly time: 50 min.
Look for video of assembly at
littletikes.com/videoinstructions
2-5
#656705M
#656705MX1
years
Cyan Magenta Yellow Black
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

2
WARNINGS!
• Keep these instructions for future reference.
• Prior to assembly, this package contains small parts: hardware which is a choking hazard
and may contain sharp edges and sharp points. Keep away from children until assembled.
• Ride-on toys should not be used near swimming pools, on or near steps, hills, roadways,
or inclines.
• Shoes must be worn at all times.
• Only one rider at a time.
• Maximum weight limit: 50 lbs. (23 Kg)
• This product is intended for use by children ages over 2 - 5 years.
• Adult supervision required. Do not leave children unattended.
• This product is intended for outdoor domestic family use only.
• Protect your eyes. Always wear safety glasses when using a hammer.
• When temperatures fall below 0°F/-18°C, outdoor use of this product is not recommended.
In extreme cold, plastic materials lose resilience and may become brittle and crack upon
impact. Store product in a warmer, protected place.
DISPOSAL
Disassemble and dispose of equipment in such a manner that no hazardous conditions such as,
but not limited to, small parts and sharp edges exist at the time equipment is discarded.
WARNINGS!
• This product contains a Button or Coin Cell Battery. A swallowed Button or Coin Cell Battery can
cause internal chemical burns in as little as two hours and lead to death. Dispose of used batteries
immediately. Keep new and used batteries away from children. If you think batteries might have
been swallowed or placed inside any part of the body, seek immediate medical attention.
Thank you for choosing the Little Tikes©T-Rex Truck.
We strive to provide a durable, easy-to-assemble toy thats made to last,
giving your child years of imaginative, engaging fun!
• Read through all the instructions rst.
• Clear a at surface to lay out all the materials so everything is close at hand.
• You will need a Phillips head screwdriver (power driver, recommended, not included)
hammer and safety glasses (not included) to assemble the T-Rex Truck.
- When installing screws, be sure screws are tightened snugly, but do NOT OVERTIGHTEN.
• Be sure to locate your decals and set aside. Decals are easier to apply when the part is
laying at, so you may want to apply the decals before assembly.
• The parts are listed below - each part is identied with a letter in RED for easy reference.
• Illustrations are for reference only. Styles may vary from actual contents.
• If you have any questions, we’re here to help. Give our customer service team a call at 1-800- 321-0183.
Really important information you should know!
Black
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

BATTERY SAFETY INFORMATION:
• Keep these instructions for future reference.
• Replace with 2“LR44”button cell batteries (not included).
• The voltage of a fully-charged, rechargeable battery is often lower than that of a fresh alkaline battery.
Therefore, it is recommended that alkaline batteries be used instead of rechargeable batteries for best
performance and longer play time.
• Install batteries with the correct polarity (+ and -).
• To avoid battery leakage:
1. Follow the toy and battery manufacturer’s installation instructions.
2. Do not mix old and new batteries.
3. Do not mix standard (carbon-zinc), alkaline or rechargeable batteries. Do not mix dierent brands
of batteries. Only batteries of the same or equivalent type as recommended are to be used.
4. When toy is not used for an extended period of time, remove batteries to prevent possible leakage and
damage to the unit.
5. Remove dead or exhausted batteries from product.
6. Dispose of dead batteries properly; do not bury. Do not dispose of batteries in re as they may leak or explode.
• Make sure cover is properly installed on unit at all times.
• Do not attempt to recharge non-rechargeable batteries.
• Rechargeable batteries are to be removed from the toy before recharging.
• Charging of rechargeable batteries should be done only by an adult.
• The supply terminals are not to be short circuited.
NOTE: If the unit stops working or doesn’t work as it should, remove the batteries for
a few minutes and then re-insert them. If there is still a problem, install new batteries.
3
Tools required (not included)
(Recommended)
(Recommandé)
(Recomendado)
Included in hardware pack.
Discard after use.
Tool color may vary.
Small cap nut tool
Remove long axle cap tool from
dashboard (part D)
Top hat tool
aa
(16) 1" (2.54cm)
Hardware Guide
Shownactualsize
Small cap nut tool
Top hat (4) Axle cap (2)
Long axle cap tool
Small cap nut (2)
Washer (6)
DD
Bushing (4)
EE
Top hat tool
CC
BB
AA
(2) 1/2" (1.27cm)
Rear axle
Bushing (2)
FF
(2) 11/2" (3.81 cm)
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

4
A Few Things Before You Start!
BEFORE you begin assembly, make sure
you have all the parts listed below.
Some packages of hardware may have extras pieces.
!
Questions? We’re here to help.
Little Tikes customer service team at 1-800- 321-0183.
!
T-Rex body (1)
Dashboard (1)
Grill cap (1)
A
D
C
H
Truck Body (1)
B
Arm - Left (1)
N1
Foot - Right (1)
K1
Door (1)
Grill (1)
E
Door latch (1)
F
Handle Bar (1)
M
Steering wheel (1)
I
Foot - Left (1)
K2
Arm - Right (1)
N2
Horn (1)
J
Steering O Ring (1)
Ia
Ib
Steering clip (1)
Reins (1)
G
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

5
Wheels (4)
O
Rear axle (1)
U
Center caps (4)
P
(1) Decal sheet
is located in the
hardware pack.
Front Wheel
Axles
Right
R
Left
L
L R
NOTE: Distance
from end to the
notch on the“Left”
axle is less than
the notch on the
“Right”axle.
Hubcaps (4)
S
Small axle (1)
T
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

6
1
Ready...let’s start with decals!
Decals must be applied to a clean, dry surface.Wipe clean with a dry rag before application.
Remove air from under decals by applying pressure to the decals starting from the center, and
work towards edges. NOTE: If decals bubble, prick with a pin to remove the air.
Decals are located
in the bottom of
the cardboard box.
1
4
3
6
213
9
10
7
812
5
11
Black
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

7
Arms first!!
Insert both arms (parts N1,N2) into theT-Rex body (part A). Push them together.
You will feel them lock into each other. Once together they will NOT COME APART.
2
N1
K1
N2
Arm - Left (1) Arm - Right (1)
Foot - Left (1)
Foot - Right (1)
A
3
Now the feet!
Fit feet, (part K1,K2) onto
each leg onT-Rex body.
Second, secure using (2)
1" (2.54cm) screws per foot.
x4
1" (2.54cm)
K2
2
Click!
You should also feel a CLICK
when inserting the lower
part of the arm into the
smaller hole on the body
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

8
Rein-in T-Rex! Attach the reins.
4
Do not hammer on
surfaces or items
you don’t want to
break, mar or dent.
Small cap nut tool
CC
Place small cap nut (part CC) into
small cap nut tool.
Insert the small axle (part T) into
the cap nut.
Hammer the axle into the cap nut.
T
Small axle
Really give it a good hit!
Small cap nut
BEFORE THREADING the axle, it
helps to clear away any excess
plastic by poking the small axle
through the holes in the head.
Thread the small axle through the reins
andT-Rex head.
Fit the reins (part G) onto theT-Rex body.
Align the holes in the reins to the holes in
the body.
Cyan Magenta Yellow Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

5
Attaching the reins -
one more step
FlipT-Rex body and reins over.
Place the small cap nut (CC) and the
small cap nut tool over the OPEN end
of the axle.
Hammer the small cap nut onto axle.
Do not hammer on
surfaces or items
you don’t want to
break, mar or dent.
CC Small cap nut
Small cap nut tool
9
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

10
6
Choose your lock
First, install door latch (part F) into door (part C)
Attach using (1) 1/2”(1.27cm) screw.
Next, insert door (part C) into truck body (part B).
TO PERMANENTLY
LOCK THE DOOR
Add (1) additional
½”(1.27cm) screw
DOOR LOCKS AND
UNLOCKS
1/2" (1.27cm)
C
C
B
F
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

11
7
Dashboard holds the door in place
Install dashboard (part D) into truck body (part B).
Be sure to t the dashboard
securely over the door pin.
Attach using (2) 11/2”
(3.81cm) screws.
D
B
Flip the truck body over
before securing the screws.
x2
11/2" (3.81 cm)
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

12
8
Attach the Grrrrill!
Slide grill (part E) onto front end of
truck body (partB).
Leave the truck body
upside down for the next
3 steps.
Secure grill using (7)
1”(2.54cm) screws.
x7
1" (2.54cm)
1B
E
3
2
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

13
9
Handle it!
TURNTRUCK BODY RIGHT SIDE UP.
Insert handle bar (part M) into back of truck body (part B).
Make sure notched
side is facing toward
the BACK!
M
B
Click
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

10
14
Ready for REAR wheels...
Do not hammer on
surfaces or items
you don’t want to
break, mar or dent.
Top hat tool
AA
Place top hat (part AA)
into top hat tool.
Insert the large axle (part U)
into the top hat.
Hammer the axle into the top hat.
U
Rear axle
Really give it a good hit!
top hat
Slide onto rear axle (1) hubcap (S), (1) wheel (O),
(1) rear axle bushing (FF) and (1) washer (DD).
SO
hubcap wheel
FF
rear axle
bushing
DD
washer
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

15
Ready for REAR wheels...cont.
DD
washer
First slide assembled axleTHROUGH
the truck body.
Next, slide (1) washer (DD) then(1) rear axle bushing (FF)
then slide wheel (O), then hubcap (S) onto axle.
S
hubcap
FF
rear axle
bushing
O
wheel
10a
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

16
AA Top hat
Top hat tool
Flip the truck on its side.
Place a top hat (AA) and the top hat
tool over the OPEN end of the axle.
Hammer the top hat onto axle.
Do not hammer on
surfaces or items
you don’t want to
break, mar or dent.
Use small cap nut tool
to SUPPORT the
bottom of axle.
Small cap
nut tool
REAR wheels...last step.
10b
Really give it a good hit!
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

17
11
And next the FRONT wheels
First, pull grill (part E) away from axle hole.
Insert (1) bushing (EE) onto each axle and
push down in place.
Right
R
Left
L
L R
NOTE: Distance
from end to the
notch on the“Left”
axle is less than
the notch on the
“Right”axle.
Axles are
NOT IDENTICAL.
Next, nd the Left
and Right Axles.
EE
bushing
EE
bushing
EE
bushing
E
Grill
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

REPEAT these steps for RIGHT front axle
Slide onto LEFT front axle (L), (1) washer (DD),
(1) hubcap (S) and (1) wheel (O).
Place top hat then top hat tool onto open
end of axle. Hammer top hat onto axle.
Top hat tool
AA
top hat
DD washer
L
L
11a
And next the FRONT wheels...cont.
18
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

Insert axle“R”(for right)
into body. Insert axle“L”(for left)
into body.
RL
And next the FRONT wheels...cont.
11b
First, slide (1) washer (DD), then bushing (EE)
onto assembled right axle.
REPEAT on left side.
Then, attach FRONT wheels and axles.
EE
bushing
DD
washer
19
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021

20
IMPORTANT! Check axle positions - roll the
T-RexTruck forward - HUBCAPS SHOULD
FACING OUTWARD.
STOP
FRONT wheels...last steps!
11c
Align slots and snap
on (4) center caps (part P)
P
Axle cap
Long axle cap tool
Really give it a good hit!
BB
Place axle cap then long
axle cap tool onto open
end of axle. Hammer axle
cap onto axle.
Repeat for other axle.
Black PANTONE 485 C
PMS Colors are Simulated
Q.C.'d by: LW Date: 03/11/2021