Little Tikes 485114 User manual

ASSEMBLY INSTRUCTIONS
Spinning Seas Water Table™
XIM485114 - 10/20
1
Adult assembly required. Approx. assembly time: 30 min.
Look for video of assembly at
littletikes.com/videoinstructions
#485114
2+
years

2
WARNINGS!
• Adult Assembly Required
• Keep these instructions for future reference.
• Prior to assembly, this package contains small parts: hardware which is a choking hazard
and may contain sharp edges and sharp points. Keep away from children until assembled.
• Adult supervision required. Do not leave children unattended.
• Use this product on a rm, level surface and avoid using near swimming pools, on or near
steps, hills or inclines.
• This product is intended for outdoor domestic family use only.
• This product is intended for use by children ages 2 years and up.
• Do not allow children to sit, stand, play or climb on the top surface. Failure to do so may
cause the product to become unstable.
• Intended for use with the supplied accessories only.
• Never ll with anything except clean tap water. Use of other liquids may be harmful
or damage the unit. Never ll with sand or dirt.
• Do not store or leave water in product when not in use.
DISPOSAL
Disassemble and dispose of equipment in such a manner that no hazardous conditions
such as, but not limited to, small parts and sharp edges exist at the time equipment is discarded.
Thank you for choosing the Little Tikes©Spinning Seas Water Table™ .
We strive to provide a durable, easy-to-assemble toy thats made to last,
giving your child years of imaginative, engaging fun!
• Read through all the instructions rst.
• Clear a at surface to lay out all the materials so everything is close at hand.
• You will need a Phillips head screwdriver, pliers (not included) to assemble the
Spinning Seas Water Table™.
- When installing screws, be sure screws are tightened snugly, but do NOT OVER-TIGHTEN.
• The parts are listed below - each part is identied with a letter in RED for easy reference.
• Illustrations are for reference only. Styles may vary from actual contents.
• If you have any questions, we’re here to help. Give our customer service team a
call at 1-800- 321-0183.
Really important information you should know!
Tools Required (not included)
(7) 3/4" (1,9cm)
Shown actual size

3
Tower Connector
Rods (3)
E
Funnel (1)
D
A Few Things Before You Start!
BEFORE you begin assembly, make sure
you have all the parts listed below.
Some packages of hardware may have extras pieces.
!
Questions? We’re here to help.
Little Tikes customer service team at 1-800-321-0183.
!
Illustrations are for reference only. Styles may vary from actual contents.
Table Top (1)
A
Legs (3)
C
Tower LEFT (1)
B1
Tower RIGHT (1)
B2
Tower Spinners (2)
F
Water Wheel (1)
G
Ferris Wheel (1)
H
Ferris Wheel Cups (3)
I
Drain Plug (1)
O
Ferris Wheel
Support (1)
J
Ferris Wheel
Crank (1)
K
Ball Flipper (1)
L
Ball Flipper (1)
L
Cup (1)
M
Balls (5)
N

4
1
Let’s get started!
First insert the drain plug (part O) into opening
on table top (part A)
Push drain plug through the opening.
A
O
Close the drain plug.
1
3
Recommended
(not included)
2
Next, ip table over.
Work the plug around the
opening, pulling only the
plug edge through.
The plug edge
should be
completely
pulled through

5
Place on at
surface before you
push legs in
Attach the legs
2
Insert table legs (part C) into table top (part A),
snap into place.
Cx3
A
Snap!
A
C

6
3a
Build the tower!
Tower LEFT (1)
B1
x3
E
11
2
2
3
Fx2
Insert (3) tower connector
rods (part E) into holes
on the tower LEFT (part B1).
Slide (2) tower spinners (part F)
on the bottom 2 tower
connector rods (part E).

7
3b
Build the tower! ...cont.
D
Align tower connector rods to
the holes in the tower RIGHT.
Push tower halves together to close.
First, place funnel (part D)
upside down on to a table.
Then slide edge of the
Tower LEFT onto tunnel.
Tower RIGHT (1)
B2
3/4" (1,9cm)
x6
Then ip the tower
upright
Secure screws (6) into place

8
4
Snap in the tower!
First, align notches in lower table top base (part A) to notches.
Then, snap tower into opening on table.
A
Snap!

9
5
Ferris wheel fun!
First place ferris wheel support (part J)
then ferris wheel crank (part K)
on the underside of ferris wheel (part H)
Next, hold ferris wheel crank and ferris
wheel support rmly, and secure
with (1) screw.
Finally, insert (3) ferris wheel cups (part I)
into ferris wheel.
J
K
3/4" (1,9cm)
x1
H
1
3
2
x3
I
I

6
Last step. Get ready to splash!
Place assembled ferris wheel (part H), ball ipper (part L)
and water wheel (part G) into the table base.
Fill with approximately 7 gallons (26.50 litres) of water
when ready to play!
G
L
H
10