Little Tikes Island Wavemaker User manual

ASSEMBLY INSTRUCTIONS
Island Wavemaker™
XIM651359-R1 - 1/21
1
Adult assembly required. Approx. assembly time: 30 min.
Look for video of assembly at
littletikes.com/videoinstructions
#651359M
2+
years

2
WARNINGS!
• Adult Assembly Required
• Keep these instructions for future reference.
• Prior to assembly, this package contains small parts: hardware which is a choking hazard
and may contain sharp edges and sharp points. Keep away from children until assembled.
• Adult supervision required. Do not leave children unattended.
• Use this product on a rm, level surface and avoid using near swimming pools, on or near
steps, hills or inclines.
• This product is intended for outdoor domestic family use only.
• This product is intended for use by children ages 2 years and up.
• Do not allow children to sit, stand, play or climb on the top surface. Failure to do so may
cause the product to become unstable.
• Intended for use with the supplied accessories only.
• Never ll with anything except clean tap water. Use of other liquids may be harmful
or damage the unit. Never ll with sand or dirt.
• Do not store or leave water in product when not in use.
DISPOSAL
Disassemble and dispose of equipment in such a manner that no hazardous conditions
such as, but not limited to, small parts and sharp edges exist at the time equipment is discarded.
Thank you for choosing the Little Tikes©Island Wavemaker™ .
We strive to provide a durable, easy-to-assemble toy thats made to last,
giving your child years of imaginative, engaging fun!
• Read through all the instructions rst.
• Clear a at surface to lay out all the materials so everything is close at hand.
• You will need a Phillips head screwdriver, and pliers (not included) to assemble the Island Wavemaker™.
- When installing screws, be sure screws are tightened snugly, but do NOT OVER-TIGHTEN.
• The parts are listed below - each part is identied with a letter in RED for easy reference.
• Illustrations are for reference only. Styles may vary from actual contents.
• If you have any questions, we’re here to help. Give our customer service team a
call at 1-800- 321-0183.
Really important information you should know!
Tools Required (not included)
Shown actual size
(4) 1 ¼" (3.17cm)(14) ¾" (1.9cm)
Tools Required (not included)

3
Steering Wheel (1)
F
Paddle Cover 2 (1)
E
A Few Things Before You Start!
BEFORE you begin assembly, make sure
you have all the parts listed below.
Some packages of hardware may have extras pieces.
!
Questions? We’re here to help.
Little Tikes customer service team at 1-800-321-0183.
!
Illustrations are for reference only. Styles may vary from actual contents.
Table Top (1)
A
Table Legs (3)
B
Skull Front (1)
H
Crank assembly (1)
C
Paddle Cover 1 (1)
D
Steering Wheel Cap (1)
G
Boat Deck Cover (1)
N
Treasure Cover (1)
O
Drain Plug (1)
P
Treasure Chest(1)
Q
Skull Back (1)
I
Slide Top (1)
J
Slide Bottom (1)
K
Palm Tree Top (2)
L
Palm Tree
Base (1)
M
Bucket (1)
R
Pirate (1)
S
Shark (1)
T
Narwhal (1)
U
Mermaid (1)
V

4
1
Let’s get started!
First insert the drain plug (part P) into opening
on table top (part A)
Push drain plug through the opening.
A
Close the drain plug.
3
Recommended
(not included)
2
Next, ip table over.
Work the plug around the
opening, pulling only the
plug edge through.
The plug edge
should be
completely
pulled through
1
P

5
Attach the legs
2
Insert 3 table legs (part B) into table top (part A),
snap into place.
Place on at
surface before you
push legs in
Snap!
Assembly Hint: 1 tbsp.
of liquid soap
Bx3

6
Get crankin’!
3
Flip table right side up. Get ready to insert
the crank assembly (part C).
C
Assembly Hint: 1 tbsp.
of liquid soap
FIRST, insert one corner of crank assembly
(part C) into opening. THEN, press opposite corner into opening, snap into place.
1
2
Snap!

7
1 ¼" (3.17cm)
x4
Insert (4) 1¼" (3.17 cm) screws to
attach the paddle cover 2 to base.
Attach the paddle cover
4
Place paddle cover 2 (part E), over crank assembly.
E
Place paddle cover 1 (part D), over crank assembly.
1
2 4
3
D
¾" (1.9cm)
x4
Insert (4) ¾" (1.9 cm) screws to
attach the paddle cover 1 to base.
1
24
3
Ridge MUST FACE
outer edge.

8
Get the steering wheel on!
5
Align notches on steering wheel (part F) wth the
slots on the axle of crank assembly.
Part is keyed to t
Part is keyed to t
F
Align slots on steering wheel cap (part G) with
notches on steering wheel and slide into place.
G
¾" (1.9cm)
x1
Insert (1) ¾" (1.9 cm) screw
through the steering wheel cap
and secure.
3
2
1
Make sure screw is tightened.

9
6
It’s time for the Palm trees!
Spins!
Snap palm tree top (L) onto palm tree base (M).
Repeat for the second palm tree
L
Mx2
Align notches on palm tree
assembly to notches on base.
Press to t each palm tree
into table.
Part is keyed to t

10
Skulls and slides, oh my!
7
Align skull front (part H) to skull back (part I)
to t together.
¾" (1.9cm)
x7
Insert (7) ¾" (1.9 cm) screws to secure.
1
2
4
3
5
67
J
K
¾" (1.9cm)
x7
Insert (2) ¾" (1.9 cm) screws to secure.Press slide top (J) onto slide bottom (K).
1
2