Livan BT1219 Manual

Manual Ver. BT 1219 - IFU 160908
®
Bluetooth Thermometer BT1219
➊On/Off
➋LEDlight
➌Temperature sensor
➍Front cover (Battery cover)

Proper Use:
TheLivan Thermometer BT1219 is a battery
powered wireless transmission device of the
sensor head under the arm or on pit of the
stomach to monitor the body temperature, and
the temperature value will show on the display.
The device transfer the measured values to
the corresponding application on user’s smart-
phone by Bluetooth
Against Indications:
The device is not suitable for use in
emergencies situations.
Caption:
This instruction manual belongs to
this device.It contains important
information about starting up and
operation. Read the instruction manual
thoroughly.Non-observance of these instructions
can result in serious injury or damage to the device.
WARNING
These warning notes must be observed
to prevent any injury to the user.
CAUTION
These notes must be observed to
prevent any damage to the device.
NOTE
These notes give you useful
additional information on the
installation or operation.
Lot number
Manufacturer
Date of manufacture
Classification: Type BF
applied part
IP22protection against solid foreign objects
of 12.5 mm Ø and greater and against
vertically falling water drops when enclosure
tilted up to 15°.
EU Representative

Manual Ver. BT 1219 - IFU 160908
EN -IMPORTANT INFORMATION!-
RETAIN FOR FUTURE USE!
Read the instruction manual carefully
before using this device, especially
the safety instructions, and keep the
instruction manual for future use.
Should you give this device to an-
other person, it is vital that you also
pass on these instructions for use.
Safety Information
zOnly use the unit for the specific purpose
described in the instruction manual. Any misuse
will void the warranty.
zA control measurement using a conventional
thermometer isrecommended in the following
cases:
1. If the reading is surprisingly low.
2. For new-born infants up to 100 days old.
3.For children under three years of age who have
a weakened immune system or who react un-
usually in the presence or absence of fever.
4. If you are using the thermometer for the first
time or want to familiarize yourself with it
zThe unit is not designed for commercial use.
zUsing this thermometer is not substitute for
consulting a doctor.
zThe unit is designed for indoor use.
zThis unit is intended measure body temperature.
zPlease put the monitor sensor on armpit or pit
of the stomach at least 10 minute when monitor
the temperature
zThis device is not designed to be used by per-
sons (including children) with limited physical,
sensory or mental abilities, or by persons with
insufficient experience and/or knowledge, un-
less under observation by a person responsible
for their safety, or unless they have been
instructed in the use of the device.
zThe patient is an intended operator
zChildren must be supervised to ensure that they
do not play with the device.
zIf a fault occurs or the unit is damaged, do not
attempt to repair the unit yourself, as this will
void the warranty. Contact your dealer and only
have repairs carried out by authorized service
partners.
zDo not open up the device. It contains small
parts which might be swallowed by children.
zDo not use the thermometer in damp
environments.
zDo not immerse the thermometer in water or
other liquids.It is not watertight.
zDo not shake or tap the thermometer. Do not
drop it.
zProtect the device from direct sunlight,
extremely high or low temperatures, dirt and
dust.
zDo not use or store the unit in an environment
where theambient temperature or humidity is
too high or too low (seeoperating conditions in
the “Technical specifications” section)
zIf the device is not going to be used for a long
period,remove the batteries.
zAvoid using any kind of sharp object to touch
the device. Do not disassemble or modified.
zBanned in high radiation environments or high
concentrations of flammable gases or nitrous
oxide environment using this device.
zThe device should not both use with CT or MRI.
zDo not use the thermometer if it is damaged.
zWhen monitor the temperature, Must regularly
checkthe contact with the skin,avoid
measurement errors.
zThe wireless transmission range may be affected
when obstructions or body height shelter
zIt may result in inaccurate measurements when
sudden movements or low battery power.
zThis device should not be used continuously for
more than 12 hours.whenfeel uncomfortable,
please stop using and remove the device.

Manual Ver. BT 1219 - IFU 160908
zOnly get genuine Parts from the original
supplier.
zBefore each use and after use, please clean the
device follow the instructionsCleaning and
Maintenance
zIf the temperature measurement result is
abnormal, please consult your doctor.
zAwarningagainstservicingandmaintenance
whiletheequipmentisinuse
BATTERY SAFETY INFORMATION
zIf a battery has been swallowed seek medical
attention immediately!
zDo not disassemble batteries!
zClean the battery and device contacts if
necessarybefore putting in the batteries!
zRemove discharged batteries from the device
immediately!
zIncreased risk of leakage, avoid contact with skin,
eyes and mucous membranes! If battery acid
comes in contact with any of these parts, rinse
the affected area with copious amounts of fresh
water and seek medical attention immediately!
Insert the batteries correctly, observing the
polarity!
zKeep the battery compartment well sealed!
zRemove the batteries if you do not wish to use
the unit for an extended period of time.
Otherwise there is a danger that the batteries
may leak.
zKeep batteries out of children's reach!
zDo not attempt to recharge these batteries!
There is a danger of explosion!!!!
zDo not short circuit! There is a danger of
explosion!!!!
zDo not throw into a fire! There is a danger of
explosion!!!!
zKeep unused batteries in their packaging away
from metal objects in order to prevent short
circuiting!
zDo not throw used batteries into the household
refuse; put them in a hazardous waste container
or take them to a battery collection point, at the
shop where they were purchased!
NOTE:
The battery contains the following
contaminants: Li (lithium)
Package Contents
Please check the package and the contents are
complete, and no any damage on it.
If in doubt, do not operate the device and associated
with the dealer or Service positions.
y1 xBluetooth thermometer BT1219
y1xCR2032, 3Vbutton battery
y1x Instructions manual
y1 x Open cover tool
y10 x 3M Double Sided Medical Tape
The packaging is reusable or can be recycled.
Observe the environmental protection rules of
regarding the disposal when you no longer need the
packaging.If you found any damage during open the
packing, contact your dealer immediately.
WARNING:
Be sure to put the packaging film out of
reach of children. Or it may cause
suffocation.
Installing and removing - battery
Install battery before using the device.
Use the open cover toolto remove the front case.
Then put the battery into the device, be sure the
battery is in the correct position. ( POSITIVE(+) IS
VISIBLE)then put pack the front cover and compact
it ,Battery drops after a period of use, the Yellow Led
will keep fast flash,please change the battery
The device is use 1 x CR2032 , 3V button battery

Manual Ver. BT 1219 - IFU 160908
Download the Application
Download and install the thermometer application
on your iOS / Android device.
You can download for free in Apple App Store or
Google Play Store
Search«LivanThermo App»
NOTE
Atypicalsmartdevicewithamaximum
outputpowerof2Wyieldsd=3.3matan
immunitylevelof3V/m
Establish a connection
Please turn on your Bluetooth on your iOS or Android
device.
Press On/Off on the thermometer at least 3 sec to
turn on the thermometer.
Lunch the App on your iOS or Android device and
follow the instruction for the application to establish
the connection with the Livan Bluetooth
thermometer BT1219, then the devices will be
synchronize.
Once the connection has been established, the
temperature is show on the screen of the App on
your iOS or Android device.
Please turn off your airplane mode and
activeBluetooth on your iOS or Android device, or the
connection will be not restricted by calls
Measuring the temperature
zPlease put the steel sensor on armpit to monitor
the temperature. Hold the position within 150
seconds, to ensure correct measurement values.
zTo ensure a good connection between the
device and the iOS or Android device, the
distance between devices should not exceed 5
meters. Connection is more secure, if the
devices is located in the ipsilateral of body
zIn normal Bluetooth connection, the scope can
reach up to 10 m, the scope can be reduced by
obstacles. (E.g wall )
zThe application on the iOS or Android device
will show the measured temperature Value by
the thermometer
Instructions
zTake a Double Sided Medical Tape stuck on the
back of the device, then stuck the thermometer.
The sensor device toward the ARMPIT or the
pit of the stomach.
zPower ON by On/Off button(Press 3 sec), all LED
on for 5 sec,blue LED continue ON for 5 min,
then put the sensor of the device on armpit or
pit of the stomach to start monitor
thetemperature.
zThe device willshow the temperature in 4 ranges
by 3 color LED, green, yellow & red
z3 color LEDtemperature indication
Green LED –
when temperature is in between 35°C ~ 37.2°
Yellow LED –
when temperature is in between 37.3°C ~ 37.9°
Red LED–
when temperature is over 38°C
zAfter using, press the On/Off button for 5 sec,
the 4 color LEDs will flash for 5 sec, then the
device will shutdown.
Note
The applied part is the sensor head.
The device has automatic shutdown when
sensor doesn’t any temperature measured
for 30 min.
Don’t stuck the Double Sided Medical
Tape on the sensor , that will Error sensing.

Manual Ver. BT 1219 - IFU 160908
Cleaning and Maintenance
zTo clean the thermometer, use a soft cloth
slightly dampened with mild soapy water or
70% isopropyl alcohol. Do not let water get into
the unit. Only use the unit again when
completely dry.
zNever use aggressive cleaning agents, thinners,
benzene or tough brushes.
zRemove the batteries if you do not wish to use
the unit for an extended period of time.
Otherwise there is a danger that the batteries
may leak.
zIf the thermometer is used as described in these
instructions, no regular maintenance or
calibration is required.
CAUTION
Do not immerse the thermometer in water or
any other liquid. It is not watertight
Disposal
This product must not be disposed of
together with domestic waste.All users are
obliged to hand in all electrical or electronic
devices, regardless of whether or not they
contain toxic substances, at a municipal or commercial
collection point so that they can be disposed of in an
environ-mentally acceptable manner.
Please remove the batteries before disposing of the
device/unit.
Do not dispose of old batteries with your household
waste, but at a battery collection station at a
recycling site or in a shop.
Consult your municipal authority or your dealer for
information about disposal.
Technical specifications
Name &model : Livan Bluetooth thermometer
BT1219
Power supply : 3V = 1 x CR2032Button battery
Battery service
life
Standby for 2 years
Continuous use for 30 days
Measuring
range : 25℃~45℃
Accuracy of
measurement : ±0.1℃
Operating
Conditions :
+5℃~ +40°C（+41°F ~ +104°F）
Relative humidity 15-95％
Atmospheric pressure 80-106KPa
Storage&
transport
conditions :
-25℃ ~ +70°C（-13°F ~ +158°F）
Relative humidity 10-95％
Atmospheric pressure 70-106KPa
Dimensions : Host :42mm x42mm x10.5mm
Material : Host: ABSplastic
Sensor: Steel
Weight : about10g(without battery)
Lifetime 2 years
Compatible
with :
iOS : 7.0 or higher.
Android:4.3or higher.
Bluetooth 4.0 or higher.
FCC ID 2AHQNBT1219
Article No. : BT1219
Manual No.: BT1219 – IFU160908
Note
The device recover from -25℃ to 20℃ will take
5 minute, recover form 70℃ to 20℃ will take 20
minute
Recommendedseparationdistances b e tw ee n
portableandmobileRFcommunicationsequipmentandth
e equipment
Theequipmentisintendedforuseinanelectromagneticenviron
mentin
whi c h radiated
RF
disturbancesarecontrolled.Thecustomerortheusercanhelp
p r e v en t electromagneticinterferencebymaintainingaminimum
di st an c e between portable
and
mobileRFcommunicationsequipment(transmitters)andth
e
equipment
a s recommendedbelow,accordingtothemaximumoutputpowe
r
R
ated max i m u m
output pow er
of t ra n sm itt er ( W )
Sepa
r
ationdistanceacco
r
ding
tofrequencyof
t ra n sm itt er
( m )
800MHzto2.5 G H z
0 . 01 0 . 23
0 . 1 0 . 73
1 2 . 3
10 7 . 3
100 23
Fortransmittersratedatamaximumoutputpowernotlistedabo
ve,therecommended
s epa r a t ion
distancedinmeters(m)canbeestimatedusingtheequationap
plicabletothefrequencyof
t he
transmitter,wherePisthemaximumoutputpowerratingofthetr
ansmitterinwatts(W)
a cc o r ding
tothetransmitter m anu f a ct u r e r.
NOTETheseguidelinesmaynotapplyinallsituations.Electro
t
i
t
i
i
f
f
t
d

Manual Ver. BT 1219 - IFU 160908
CE certification of the device refers to the EU
Directive 93/42 / EEC.
we declare that the Livan Bluetooth thermometer
BT1219, art. BT 1219, respects the fundamental
requirements of the European R & TTE Directive
1995/5 / EC.
You can request the complete conformity EC
declaration to Livan Technology Co., Ltd.
Electromagnetic compatibility：
The device complies with the EN 60601-1-2 standard
for electromagnetic compatibility.
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the
grantee of this device could void the user's authority to operate
the equipment.
FCC Label Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference.
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Exposure to Radio Frequency Radiation:
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This transmitter must not
be co-located or operating in conjunction with any other antenna
or transmitter.
Livan Technology Co., Ltd
3F., No.3, Ln. 133, Baozhong Rd., Xindian Dist.,
New Taipei City 23144, Taiwan(R.O.C)
E-mail:[email protected]
Emergo Europe B.V.
Molenstraat 15, 2513 BH The Hague,
The Netherlands.
In accordance with our policy of continual product
improvement, we reserve the right to make technical
and optical changes without notice.
0434