Living Spaces 7030-01255 KIT User manual

Sedona Collection: Big Sky Bunk
PARTS LIST
BOX 1: 4145 Big Sky Bunk Ends
Part # Description Quantity
S0001END Big Sky Bottom End 2
S0002END Big Sky Top End
2
BOX 2: 4144 Big Sky Frame
Part #
Description Quantity
S1001SRL 5/4 x 6 x 75 Mattress Rail 4
541750001 5/4 x 4 x 75 Guard Rail 4
140533/40 Full Individual Slat 3
FLDWL 3" Fluted Dowel 4
5040-43181 Hex Lag Bolt/Washer 32
5040-35410 #6 x 1 1/4 Phil Flat Slat Screw 20
Picture
Picture
7030-01255 KIT
For: 4144 Frame Rails/4145 Bunk Ends
COMPLETED ASSEMBLY

1) Attach two mattress rails(S1001SRL) to two bottom end assemblies(S0001END) with 8 lag bolts and 8
washers(5040-43181), and tighten.
2) Attach two mattress rails(S1001SRL) and four guard rails(541750001) to top end assemblies(S0002END) with 24
lag bolts and 24 washers(5040-43181), and tighten.
3) Place four wooden dowels(FLDWL) in the four holes in top edge of bottom bunk assembly.
4) Place the top bunk assembly on the bottom bunk assembly, ensuring that the dowels are inserted in holes in the top
bunk assembly.
5) Place slat kit (purchased separately) and 3 individual slats(140533/40) in accordance with the diagram on the last
page of these instructions. Attach the 5 designated slats to the mattress rail cleats using the #6x1 ¼”
screws(5040-35410).
5040-43181
S1001SRL
S0001SRL
S0002SRL
FLDWL
54175001

00500
SAFETY WARNING
Our Bunk Beds have been tested by an Independent Laboratory and are certified to be in compliance with:
ASTM F-1427, “Standard Consumer Safety Specification for Bunk Beds” and U.S. Government
specifications 16 Code of Federal Regulations, parts 1213 and 1513.
SAFETY WARNINGS
1. Follow the information on the warnings attached to the upper bunk end structure and on the carton. Do
not remove this label.
2. Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood
of entrapment or falls.
3. Top surface of mattress must be at least five inches (127mm) below the upper edge of top guard rails.
4. Do not allow children less than six years of age to use the upper bunk.
5. Periodically, check and ensure that the guardrail, ladder and other components are in their proper
position, free from damage and that all connectors are tight.
6. Do not allow horseplay on or under the bed and prohibit jumping on the bed and ladder.
7. Prohibit more than one person on upper bunk.
8. Always use the ladder or bed end for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Living Spaces for replacement parts.
10. Use of a night-light may provide added safety precautions for a child using the upper bunk.
11. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be
placed against the wall to prevent entrapment between the bed and the wall. (This applies only to bunk
beds without two full-length guardrails.)
12. Always use guardrails on both long sides of the upper bunk.
13. The use of water or sleep flotation mattress is expressly prohibited.
14. Keep these instructions for future reference.
STRANGULATION HAZARD
15. Never attach or hang items to any part of the bunk bed that are not designed for use with the bed for
example, but not limited to hooks, belts and jump ropes.
SIZE OF MATTRESS AND FOUNDATION
Your Twin bed is designed to use a mattress 37”-39” in width and 74” - 75” in length.
Your Full bed is designed to use a mattress 52”- 54” in width and 74” - 75” in length.
The total thickness of mattress and foundation (slat kit, bunk board, etc.) combined must not exceed 10”.
Note: There must be at least 5” from mattress sleeping surface to top edge of guardrail.
REPLACEMENT PARTS
Replacement parts, including additional guardrails, may be requested from Living Spaces, usually at a cost.

Installation of individual slats for use with Slat Roll (Slat roll sold separately) See your retailer for purchase of Slat Roll
SCREW
SCREW
SCREW
SCREW SCREW SCREW SCREW
SCREW
SCREW
SCREW
INDIVIDUAL SLATS INDIVIDUAL SLATS INDIVIDUAL SLATS
Installation of individual slats for use with Bunkie Board (Bunkie Board sold separately) See your retailer for purchase of Bunkie Board
SCREWSSCREWSSCREWSSCREWSSCREWSSCREWS
INDIVIDUAL SLATS INDIVIDUAL SLATS INDIVIDUAL SLATS
When used with a slat roll, the three
individual slats should be placed evenly in the gaps and underneath the strapping before fastening.
Individual Slat
Individual Slat
Individual Slat
Diagram 1 Diagram 2
Scan Code for Instructional video