Logic ZOOM SDK User manual

ZOO M
QuickStart Guide www.logicpd.com
:: Zoom SDK ::

ZOOM SDK
QuickStart Guide
We fast forward
the evolution of
new products.

ZOOM SDK
2 QuickStart Guide
Table of Contents
1Introduction 4
1.1 Zoom Starter Development Kit Features 4
2 Getting Started 6
2.1 Unpacking the System 6
2.2 CD-ROM Contents 7
2.3 Development PC Requirements 7
2.4 Application Baseboard Connection Diagram 8
3QuickStart 10
3.1 Inserting the Card Engine into the Baseboard 10
3.2 Removing the Card Engine from the Baseboard 11
3.3 Connecting the Zoom Starter Development Kit to your PC 12
4 Test Drive the Zoom Starter Development Kit 14
4.1 Software Installation 14
4.2 Power-up the Development Kit 15
4.3 Software Development Tools 15
4.4 Sample Application 15
4.5 Board Support Packages (BSPs) 16
5 Product Notices 17
6 Product Registration 18
7 Zoom Display Kits 19
7.1 Zoom Display Kit Features 20
8Support 21
8.1 Frequently Asked Questions 22
8.2 Technical Discussion Group 22
9 Warranty Statement 23

ZOOM SDK
QuickStart Guide 3
Table of Figures
Figure 2.1 –Kit Contents 6
Figure 2.2 –Connection Diagram for the Application Baseboard 8
Figure 3.1 –Inserting the Card Engine into the Baseboard 10
Figure 3.2 –Using the Logic Card Engine Extractor Tool 11
Figure 3.3 –Connecting the Baseboard to your PC 12
Figure 3.5 – Example JTAG Settings for Sharp LH79520 13
Figure 4.1 – Tera Term: Serial Port Setup Window 14
Figure 4.2 –LogicLoader (Bootloader/Monitor) Menu 15
Figure 7.1 –Zoom Display Kit plugged into a Zoom Starter Development Kit 19

ZOOM SDK
4 QuickStart Guide
1 Introduction
Congratulations on your purchase of the Zoom™ Starter Development Kit (SDK). The Zoom
Starter Development Kit provides a product-ready software and hardware platform for
evaluating the functionality of Logic’s Card Engine module and the associated processor.
Logic’s embedded solutions fast forward product development and helps your company stay
focused on your high-value core technologies.
1.1 Zoom Starter Development Kit Features
Common Features
+Card Engine
+MCU and System on Chip (SoC) features specific to Card Engine model
+LCD display interface
+Integrated LCD, touch, and backlight connector
+Network support
+RJ45 Ethernet jack with magnetics
+Audio
+Stereo input and output jacks (refer to specific Card Engine for support)
+PC card expansion
+CompactFlash® Type 1 card (memory-mode only)
+Serial port
+115.2kbps RS-232 debug serial port
+Expansion headers
+Access to all Card Engine signals
+Standard 100 mil pitch
Cables & Tools
+Serial cable (null-modem)
+5 volt power supply with power adapters
+Ethernet cross-over cable (dependent upon the Zoom Starter Development Kit
purchased)
+Card Engine extractor tool
Software
+Logic provides sample downloadable Windows® Embedded CE and Linux Board
Support Packages (BSPs), dependent upon the Card Engine model purchased with
the Zoom Starter Development Kit
+LogicLoader™ (bootloader/monitor) installed in the Card Engine flash

ZOOM SDK
QuickStart Guide 5
Application Development Tools
+Cygwin1, Tera Term, and GNU cross development toolchain1
+Card Engine-specific Software Development Tools1for use with Microsoft®
Embedded Visual Tools on Windows Embedded CE supported Development Kits
Mechanical
+102 mm long x 152 mm wide x 16.8 mm high
1. Available as downloads from Logic’s website. Please create an account and
register your product to access these software tools:
http://www.logicpd.com/auth/.

ZOOM SDK
6 QuickStart Guide
2 Getting Started
2.1 Unpacking the System
The Zoom Starter Development Kit is comprised of the following items:
+Application baseboard
+Card Engine
+CD-ROM (see "CD-ROM Contents" Section)
+Ethernet cross-over cable (dependent upon the Zoom Starter Development Kit
purchased)
+Null-modem serial cable (use only the null-modem cable provided with the kit)
+Regulated 5V power supply with power adapters (Europe, Japan, UK, and US)
+Card Engine extractor tool
+End-User License Agreement
+Warranty card
+QuickStart Guide
Note: Avoid touching the MOS devices. Static discharge can and will damage these devices.
Once you have verified that all the items are present, remove the Card Engine and application
baseboard from their anti-static bags. Check the boards for any visible damage and ensure
that there are no broken, damaged, or missing parts.
Figure 2.1 – Kit Contents
Application Baseboard
Card Engine
Power Adapters
(Europe, Japan,
UK, and US)
Regulated 5V
CD-ROM
Ethernet
Cable
Cross-over
Null-modem
Serial Cable
Power Supply
Card Engine
Extractor Tool

ZOOM SDK
QuickStart Guide 7
2.2 CD-ROM Contents
Product Documentation1
+Card Engine and Development Kit product briefs
+Bill of Materials (.pdf format) for Card Engine and application baseboard2
+Schematics for Card Engine (.pdf format) and application baseboard (.pdf and .DSN
formats)2
+Layouts for Card Engine (.pdf format) and application baseboard (.pdf and .MAX
formats)2
+Card Engine Hardware Specification
+Card Engine I/O Controller Specification
+SDK QuickStart Guide
+SDK User’s Manual
+LogicLoader User’s Manual
+Card Engine-specifc LogicLoader User’s Manual Addendum
Software Development Tools1(Refer to tool-specific readme files for instructions)
+Te r a Te r m
+Cygwin2
+GNU cross development toolchain2
+Sample application2
References, Resources, and Support
+FAQ, Technical Discussion Group (TDG)
+How to get technical support (Ask a Question)
+Support Packages
Product Registration & Software Downloads
2.3 Development PC Requirements
General
+Windows® 2000 or later host PC with access to the Internet
+Pentium® processor or equivalent
+64 MB RAM minimum
+1 GB free hard disk space
+115200 baud capable RS-232 port (COM port)
+Tera Term serial emulation program (or equivalent)
1. May vary across Development Kits.
2. Available as downloads from Logic’s website. Please create an account and
register your product to access and be notified of the latest updates to these
documents: http://www.logicpd.com/auth/.

ZOOM SDK
8 QuickStart Guide
For Windows Embedded CE development (sold separately, contact Microsoft)
+Host PC running Windows 2000 or Windows XP
+Windows CE Platform Builder for creating Windows Embedded CE images
+Microsoft Embedded Visual Tools for application development
+Ethernet cross-over cable
For Linux development
+Host PC running Windows 2000 or Windows XP / Cygwin or Linux
+GNU cross development toolchain
2.4 Application Baseboard Connection Diagram
Figure 2.2 – Connection Diagram for the Application Baseboard
O P Q A B C D
E
GHIJK
N
M
L
F