GB
Unpacking
11
Operating Your Remote Control
22
Installing the Base Stand
33Turning the TV On for the First Time
66
Connecting to the Mains Socket
55
Connecting the Aerial
44
Thank you for purchasing your new Logik TV.
Your new TV incorporates the latest technology to enhance your
viewing experience. We would suggest that you allow about 20
mins for initial setup.
Please follow this guide for a successful rst time installation.
Remove all packaging from the TV. Retain the packaging. If you
dispose of it please do so according to any local regulations.
Install the batteries correctly by following the polarity
(+ and -) indications in the battery compartment.
1. Press and lift the back
cover up to open the
battery compartment
of the remote control.
1. Press the OK button to
start First Time Installation.
2. Insert two AAA size
batteries. Close the
battery compartment
cover.
The rst time you turn the TV on, it will go straight into First Time Installation.
Well done, your new TV is now ready to use. You will nd that there are many exciting features available. To get to know all these
features, please take some time to read the instruction manual provided with your TV.
If after reading the instruction manual you have additional questions related to the use of your TV please call our UK Call Centre on 0844 561 1234.
Our UK Customer Contact Centre is open Monday-Saturday 8am-8pm or Sunday 8am-6pm.
(P.N.: 4033C221308)
First Time Installation
Please ensure aerial is plugged in!
Then press OK button.
2. Press the OK button to
conrm English as your
desired language to be
displayed on the menu.
3. Press the OK button to
conrm UK as the country
where you will operate the
TV.
4. Channel tuning will
commence. This
operation may take up to
6 minutes. The display
will show the progress of
the tuning and the
number of channels
found.
Dan sk
Deu tsc h
Hrv ats ki
Ita lia no
OSD Language
OK
Mag yar
Ned erl and s
Nor sk
Pol skiEnglish
Ces ky
E k
Espanol
~
Fra n ais
Portugues
Pyc ck
Fra nce
Gre ece
UK
Australia
Austria
Cze ch
Den mar k
Fin lan d
Country
OK
Bel giu m
Bul gar ia
Croatia
Hungary
Ita ly
Lux emb our g
Germany
Channel Tuning
TV : 3 Channel(s)
DTV : 0 Channel(s)
Radio : 0 Channel(s)
Date : 0 Channel(s)
36%... 668.75MH z (T V)
Please press MENU to skip.
Quick Start Guide
L22DIGB11
22” HD Ready 1080p Digital LCD TV
LCD TV
Base Stand Quick Start Guide
Digital Switchover
Addendum
Remote Control /
AAA Batteries x 2
Screw A
Instruction Manual
1. Lay the TV down on a at surface with the back side facing up.
Please make sure to place a soft cushioned material (such as a
pillow or thick piece of foam) beneath the screen.
2. Align the screw hole and then secure the base stand with the
provided 1 screw.
Screw A x 1
(P.N.: 209100412B1)
screw
Connect one end of the RF coaxial cable to the aerial socket on
the wall and the other end of the cable to the RF IN (75Ω) socket
on the right rear side of your TV.
Do not connect the TV to the mains supply until you
have completed all the connections.
OR
RF coaxial cable
(not included)
100-240 V~ 50/60Hz
VIDEO
AC-INPUT
HDMI INPU T
PC
AUDIOINPUT
SCART
VGA INP UT RF INPU T
1. Connect the mains cable to the mains socket after you have
completed all the connections.
2. At this stage, the TV switches to standby mode. The red LED
indicator will illuminate on the front panel of the TV.
3. In standby mode, press the button on the side panel of the
TV or on the remote control to turn the TV on. The red LED
indicator will turn green.
To mains socket
L22DIGB11_QSG_110315_Annie.pdf 1 11年3月15日 上午11:38
