Logitech Harmony 350 Remote User manual

Harmony® 350 Remote
Setup Guide
Guide d’installation

Harmony 350 Remote
2
AA AA
USB

Harmony 350 Remote
3
Contents
English. . . . . . . . . . . . . . . . . . 4 Français . . . . . . . . . . . . . . . . 10

Harmony 350 Remote
4 English
Buttons
1. Watch TV button: Powers devices on/o
for your Watch TV Activity
2. Device buttons: Set the remote
to control specific devices
3. Favorite Channel buttons:
Configure these buttons for quick access
to favorite TV channels.
4. Color buttons: Navigate menus
and select options on some TVs,
cable/satellite receivers, DVRs,
and Blu-ray players
5. Power button: Select one of the Device
buttons, then use the Power button
to turn that device on or o.
1
2
5
3
4

Harmony 350 Remote
English 5
How the remote works
Harmony 350 is an infrared (IR) remote that controls other IR devices such as TVs,
audio/video receivers, and cable/satellite receivers. Visit setup.myharmony.com to create
an account and set up your new Harmony remote.
Watch TV button
Set up a Watch TV Activity to automatically power on/o devices
you use to watch TV, such as your TV, audio/video receiver,
and cable/satellite receiver. After pressing the Watch TV button,
be sure to keep the remote pointed at your devices until the Device
buttons turn o. Press the Watch TV button again to turn o all
the devices.
Device buttons
Control up to eight devices individually using these four Device
buttons, each with a short press or a longer two second press.
Each Device button will light up when an IR command is being sent.
Favorite Channel buttons
Program up to five Favorite Channels for your TV or cable/
satellite receiver.
To make changes after setup, sign in to your account at myharmony.com

Harmony 350 Remote
6 English
Setting up your Harmony 350
1. Install the batteries
Insert the two AA batteries (included)
into the battery compartment.
2. Gather your device information
In order for Harmony 350 to control
your entertainment system, we’ll need
to know the manufacturer and model
number of each of the devices you own.
The manufacturer and model number
of your devices are typically printed on
the front bezel, or on a label located on the
bottom or the back of your entertainment
devices. Write them down in the table
provided on the back page of this Setup
Guide for quick reference during setup.
AA

Harmony 350 Remote
English 7
3. Complete setup online.
Complete the setup online via
setup.myharmony.com
a. Connect your Harmony 350 to
your computer using the supplied
USB cable.
b. Open a browser and go to
setup.myharmony.com
c. Follow the on-screen instructions
to create a Harmony account and
set up your remote.
Test your remote
Once you’ve completed the online setup
and synced your Harmony 350, please test it.
1. Unplug your Harmony 350 from
your computer and take it to your
entertainment system.
2. To test your remote, press the Watch TV
button. Make sure to keep the remote
pointed at your devices until the Device
buttons are no longer lit. If you did
not set up a Watch TV Activity, test by
pressing the Power button to power
a device on and o.
3. To make changes, connect the remote
to your computer and sign in to
your account at myharmony.com
Note: Once setup is complete,
use Harmony 350 as your only remote;
using other remotes could cause the devices
in Watch TV Activity to become out of sync.
USB
myharmony.com

Harmony 350 Remote
8 English
Frequently asked questions
• How do I customize buttons or change my Favorite Channels?
Sign in to your account on myharmony.com, plug in your remote using the included
USB cable, then click on the Buttons tab to customize buttons and the Favorites tab to
change Favorite Channels. When changes are completed, be sure to sync your remote.
Troubleshooting
• The remote does not seem to work with my device.
First ensure that fresh batteries are inserted properly into the remote. Then check that
one of the four Device buttons should flash when a button is pressed. Refer to support.
myharmony.com/350 for more information.
• Pressing the Watch TV button does not properly turn on all my devices and set them
to the correct inputs.
The devices must be in the same power state, on or o, at all times in order for the Watch
TV button to function properly. Use the Device buttons in combination with the Power
button to keep the devices in the same power state. Refer to support.myharmony.com/350
for more information.

Harmony 350 Remote
English 9
Get support
For more detailed information, please visit support.myharmony.com/350
• Finding answers to questions
Visit our knowledgebase at support.myharmony.com/350
• Getting help with online setup
Many screens and pages presented to you during the online setup contain
‘Learn more’ or ‘Help’ links designed to provide additional information or assistance
with various features.
• Logitech’s Harmony Remote user forums
Visit the Harmony Remote User Forums located at forums.logitech.com

Harmony 350 Remote
10 Français
Boutons
1. Bouton Regarder la TV:
Met sous tension ou hors tension
vos dispositifs pour votre activité
Regarder la TV
2. Boutons Dispositif:
Configurez la télécommande pour
contrôler des dispositifs spécifiques
3. Boutons de chaînes préférées:
Configurez ces boutons pour accéder
rapidement à vos chaînes TV préférées.
4. Boutons de couleur:
Naviguez dans les menus et sélectionnez
des options sur certains téléviseurs,
récepteurs câble/satellite, enregistreurs
numériques et lecteurs Blu-ray.
5. Bouton d'alimentation:
Sélectionnez un bouton Dispositif,
puis utilisez le bouton d'alimentation
pour mettre le dispositif correspondant
sous ou hors tension.
1
2
5
3
4