Look Solutions Power-Tiny User manual

1
Power-Tiny
aLook Solutions product
Operating manual

2
Set of Equipment supplied
–1Power-Tiny with battery pack and fluid tank 250 ml
–1charger
–1bottle of fluid 250 ml
When the order includes a radio remote, the following items are supplied
additionally:
–1receiver with 3 pin XLR-plug
–1radio remote
–1manual „Radio remote control“
Please check whether all the products you ordered are supplied.

3
Contents
1. Procedure of the Power-Tiny 4
2. Safety Instructions 5
3. Description of the parts 6
4. Fluid 7
4.1 General
5. Operating the Power-Tiny 7
5.1 Selecting the Location
5.2 Mounting the Power-Tiny
5.3 Starting-up the Power-Tiny
5.4 Control choices
5.4.1 0 - 10 Volt (+) DC control
5.4.2 Control via Radio remote
5.4.3 Others
5.5 Status Display of the Battery/Sleep mode
5.6 Changing the battery pack
5.7 Wiring of the connector
6. The battery pack 9
6.1 Capacity
6.2 Operating and Storing
6.3 Charging the Battery
6.4 Safety Instructions
6.5 Technical Data
7. The Charger 11
7.1 Operating the Charger
7.2 General Notes
7.3 Technical Data
8. Service and Maintenance 13
8.1 The machine does not work perfectly
8.1.1 There will be no fog if…
8.1.2 The yellow LED lights permanently if…
8.2 Care and Maintenance
9. Technical Data 14
10. Warranty Conditions 15

4
1. Procedure of the Power-Tiny
The Power-Tiny is a battery-operated, microprocessor-controlled fog generator.
It is based (as most fog generators) on the vaporizer principle, i.e. a glycol fluid is
evaporated and condenses into fog when leaving the fog nozzle. However, the
Power-Tiny only heats when fog is actually needed.
Because of the sleep mode the machine uses only 1.5 milliamperes in idle
status and consequently it may remain connected to the the battery for several
hours with no discharging to speak of – the standby-time is approx. 250 hours.
The following sequence produces fog:
a) Warming up (1 second, without pumping fluid).
b) The pump runs
c) Pump stops but fog will be produced for several seconds to get all the fluid out
of the vaporizer.

5
2. Safety instructions
A fog machine is not a toy!
•Very hot steam escapes from the nozzle. Danger of getting burnt.
•Occasionally very hot droplets of fluid may escape when in operation.
Thus never aim at persons directly and keep a minimum distance of 10 ft from
the nozzle.
•Never touch the nozzle when in operation. Danger of getting burnt.
•The location for the machine must be non-flammable, non-combustible and
not sensitive to heat. It has to be twice as big as the machine.
•Keep a minimum distance of 2 ft from all flammable, combustible objects and
objects sensitive to heat.
•Glycol is alcohol and burns with a slightly bluish, almost invisible flame. Never
point the fog at strong sources of ignition like fire or pyrotechnic effects.
•Never open the machine and leave the machine unattended when connected
to a power supply.
• The visibility has to be more than 6 ft in rooms where people walk around.
•Only use the supplied TINY-FLUID. Different types of fluid do not generate the
fog you require and destroy your fog generator.
•Do not swallow the fog fluid. Keep it away from children. In case of eye contact,
rinse with a lot of water. Consult a doctor should you have accidentally
swallowed some fluid.
•Spilled fluid or splashed fluid droplets can cause slip hazard. Mop up the fluid
and dispose of it according to regulations. TINY-FLUID is completely water-
soluble and biodegradable.
•Fog may activate smoke detectors.
•Use only Look Solutions Tiny-Fluid in this machine.
Artificially-made fog can be produced in many different ways. The method
used here to produce fog, with a device which works according to the vaporizer
principle, is the most harmless one.
No case has so far been reported in which a sound human being has been
harmed because of using our device to produce artificial fog. However, this can
only be guaranteed if the professional fog generators are used accordingly, i.e.
at the correct vaporization temperatures as well as with the correctly mixed fog
fluid.
We, however, recommend: People with health problems or problems of the
respiratory tract or with an inclination for allergies should avoid any contact
with artificially-made fog.

6
3. Description of the parts
5: · Fluid tube
6: · Battery connector (Speakon)
7: · Screws (thumb screw)
8: · Quick-connector for fluid tube
9: · Fluid tank
· Adjusting knob
· LED/Battery status display
· Socket for battery plug
· 3pin-XLR-socket
10:
11:
12:
13:
1: · Start button
2: · Fog nozzle
3: · Socket for charger
4: · Battery pack
(Battery with housing,
PCB, fuse and connector)
1
2
3
4
5
6
7
8
9
10
11
12
13

7
4. Fluid
5.1 Selecting the Location
The location for the Power-Tiny must
•be dry
•guarantee sufficient air supply
•have sufficient distance (at least 2 ft) from inflammable materials
•have very little vibration
•have an ambient operating temperature between 40°F and 115°F
•have a relative air humidity of less than 80%.
5.2 Mounting the Power-Tiny
If the Power-Tiny is to be built in props or similar, make sure that a fog-free air
supply is guaranteed. Too high fog concentration can condense inside the machine
and can result in damages caused by moisture.
When installing the Power-Tiny make sure that
•no fog is passed back into the fog generator,
•no condensed fluid runs into the apparatus,
•no objects jut out into the fog nozzle [2]
1) Pour the TINY-FLUID into the fluid bottle and firmly lock the bottle. Plug the
connecting spout of the fluid tubing into the quick connector of the fluid
bottle (audible click).
Check the cleanness of the fluid bottle, so that no dirt (fluff etc.) can be sucked
in by the pump. Even the smallest impurity immediately leads to clogging of
the machine.
2) Connect the battery pack to the machine. Therefore plug in the battery
connector (Speakon) [6] into the socket [12]‚ at the back of the machine.
3) Press Start-key (grey) [1] briefly.
4.1 General
The Power-Tiny is built to be used with original Look Tiny-fluid. Use of other
liquids will clog the vaporizer and void the warranty.
5. Operating the Power-Tiny
5.2 Starting-up the Power-Tiny

8
5. Operating the Power-Tiny
5.4 Control choices
You may control the Power-Tiny externally through the XLR socket [12].
5.4.1 0 - 10 Volt (+) DC control
Connect the Power-Tiny to an analog desk or with the cable remote (available
as an optional extra), using the XLR socket [12] at the back of the machine.
a) Connect the cable from the desk or the cable remote into the XLR socket at
the back of the machine [12].
b) The knob on the cable remote or the fader on the analog desk will control the
level of the pump.
c) Pressing the On/Off switch at the cable remote starts the fog process.
5.4.2 Control via Radio remote
A radio remote is available as an option. It will be delivered with a 3pin XLR
plug.
a) Connect the receiver of the radio remote to the machine, using the 3pin XLR
socket [12] on the back of the machine.
b) Adjust the requested pump output at the machine, turning the adjusting knob
[10].
c) Press the first button at the transmitter of the radio remote as long as you
want fog to be produced (see manual „Radio remote“).
5.4.3 Other controls
DMX 512: Connect the DMX-converter (DMXit, available as an option) to the
machine, using the 3pin XLR-plug [12].
Now the Power-Tiny can be connected to a DMX desk and can be controlled via
DMX.
Timer: Connect the Timer (TIMEit, available as an option) to the machine, using
the 3pin XLR-plug [12].
Now the wait and the fog time as well as the output can be programmed in.

9
5. Operating the Power-Tiny
5.7 Wiring of the connector
5.5 Battery Status Display/Sleep mode
The yellow light-emitting diode (LED) [11] on the Power-Tiny indicates how
strong/efficient the battery still is and/or when it must be recharged.
1) LED flashes slowly: Battery capacity of 15% – 100 %, the battery is fully
operational.
2) LED flashes fast: Battery capacity below 15%, the battery should be changed
and/or charged.
3) LED lights up permanently: the battery is flat or the vaporizer is damaged
4) LED does not light although the battery is connected:
Approx. 40 Seconds after the last fogging the Power-Tiny changes into the
sleep mode automatically. It then only needs a current of 1.5 mA. To awake
the machine press the startbutton [1].
3pin XLR (analog):
Pin 1 = Ground, Pin 2 = 0-10 V + DC in, Pin 3 = 12 V + DC out, max. 50 mA
5.6 Changing the battery pack
The battery pack [4] can be changed on site, for example if one battery pack is
empty and there is not enough time to recharge it.
To change the battery pack [4] unplug the battery connector [6] from the
machine. Unscrew the thumb screws [7] and disconnect machine and battery pack.
Put the Power-Tiny on a new battery pack and fix it with the screws. Connect the
battery pack to the machine.
6. The battery pack
The supplied battery pack is supplied with a maintenance-free 12V lead-gel
accumulator which is calibrated in the best possible way with the connected loads
of the Power-Tiny. It can be used in every position.
The connection to the Power-Tiny is done with a Speakon NL4FX high current
plug, the connecting to the charger is done with a small connector.

10
6.4 Safety Regulations
6.3 Charging the battery
6.1 Capacity
6.2 Operating and Storing
The battery has a capacity of 12 Ah and is supplied in a charged status. A fully-
charged battery can generate more than 100 fog emissions of 4-5 seconds. The
permanent fogging time amounts to 10 minutes.
When used correctly, the battery holds its capacity for several years and/or some
hundred charge/discharge cycles.
Lead-gel batteries are a very robust bank of capacitors which need little care
and maintenance. However, their working life can be shortened rapidly by storing
them when discharged.
Caution: Do not store a discharged battery! As a result, it can lose a large part
of its capacity after two weeks!
For charging the battery please use the supplied automatic charger. A discharged
battery can be charged within 10 - 12 hours.
If the battery is in charge, the LED at the charger lights red. If the battery is
fully charged, the LED lights green.
6. The battery pack
•The supplied battery can supply high discharging currents. Therefore:
– Never short-circuit the battery.
– Never change the cable sizes.
•Positioning of the battery
– Make sure the battery is not placed near sources of heat,
– Should you place your battery near a source of heat, the performance of the
battery will decrease the more the temperature rises.
•Using the battery in closed units
– Don‘t use the battery in completely sealed casings or units.
– To prevent a blast of hydrogen leaking from the battery, the casings must be
ventilated.
•Dismantling the battery
– Don‘t dismantle batteries as they do contain electrolytes which may damage
clothing or hurt the skin. If the electrolyte comes in contact with skin or eyes,
immediately rinse with water or consult a doctor.

11
6. The Battery pack
7.1 Operation
An automatic charger for 12 V lead-gel battery is supplied.
•Connect the charger to a power socket (100-240 V~/50Hz–60Hz).
•Connect the output line of the charger with the battery to be charged.
•Check whether the charge display (LED) lights red.
•Agreen lighting LED shows that the battery is fully charged.
•Disconnect the charger from the socket.
•Disconnect the battery from the charger.
•Avoid short-circuits
– Do not short-circuit the Speakon-cable. This will destroy the FKS-fuses.
•Keep away from fire
– Do not expose the battery to fire or burn it. The battery might explode.
6.5 Technical Data
Model Lead-gel battery
Output voltage 12 V / 12Ah
Temperature range 40°F to 115°F
Dimensions 22 x 10 x 11.5 cm
Weight 4.5 kg
7. The Charger

12
7. The Charger
7.2 General Notes
1) If the control display lights up red permanently, this might indicate probable
battery problems:
• short circuit within the battery or in the output lines
• the battery voltage can not reach 13.8 V (especially in the case of old batteries)
2) Protect the unit against rain
3) Use the charger exclusively for charging the Power-Tiny battery
7.3 Technical Data
Model MPP 15 or similar
Input voltage 90 - 240 V~ / 50 Hz - 60 Hz
Output voltage 12 V = / 1000 mA
Operating temperature 32°F to +105°F
Display < 75 mA LED lights green (battery is
fully charged)
< 300 mA, UB> 6 V LED lights red
(battery is in charge)
Dimensions 8.75 x 5.15 x 3.4 cm
Weight 165 g

13
8. Service and Maintenance
8.1 The machine does not work perfectly
•the battery is discharged (yellow charge indicator (LED) lights up permanently,
the pump automatically cuts off) => charge the battery
•the fluid tank is empty => refill the fluid tank
•the vaporizer is clogged or broken
8.1.1 There will be no fog if…
•the battery is discharged => disconnect the machine from the battery and charge
the battery
•the vaporizer is clogged or broken
8.1.2 The yellow LED lights permanently if…
8.2 Care and Maintenance
To ensure perfect performance of the Power-Tiny, you should consider the
following notes:
•Make sure the fluid bottle is clean and free from small bits of dirt.
•Clean the unit from time to time, especially if you use it in a built-in state/
condition.
•If the Power-Tiny is not in use for a longer time, please take care that the
battery is disconnected. The battery should be charged before storing.
•PLEASE NOTE: It is not necessary to clean the vaporizer! Cleaning with any
liquid/fluid can destroy the heat exchange module!

14
9. Technical data
Procedure Vaporizing fog generator
Power requirement 400 Watts
Voltage 12 V battery
Warm up time 1 sec
Fluid tank capacity 250 ml
Fluid consumption 10 ml/min. with continuous output
Continuous output with battery 10 min.
Temperature control microprocessor
Control start button
radio remote (option)
XLR-remote (0 - 10 V analog)
DMX 512 via converter
Timer
Dimensions (L x W x H) 22.3 x 10 x 21 cm
Weight 5.6 kg
Manufactured for Look – Solutions made in Germany

15
10. Warranty conditions
For the fog machine Power-Tiny Look‘ guarantee is:
1. Free of charge, subject to the following conditions (No. 2 - 6) we will repair any defect or
fault in the unit if it is caused by a proven factory fault and has been advised immediately
after appearance and within 12 months of delivery to the end user. Insignificant deviations
of the regular production quality does not guarantee replacement rights, nor do faults
or defects caused by water, wrong fog fluid, by generally abnormal environment
conditions or Force Majeure.
2. Guarantee Service will be done in the following way: Faulty parts will be repaired or
replaced (our choice) with correct parts. Faulty units have to be brought to us or our
service centres or to be sent to us or our service centres at customer‘s expense. The
invoice and/or receipt showing the purchase date and the serial number has to come
with the faulty unit, otherwise this will not be guarantee service. Replaced parts become
our property.
3. The customer loses all rights for guarantee services, if any repairs or adjustments are
done to the units by unauthorized persons and/or if spare parts are used which are not
approved by us. The right of guarantee service is also lost if fluids other than the original
Look „TINY-FLUID“ have been used or if units are sent to us with full fluid bottles. Also
non compliance with the instructions in this manual or mistakes by incorrect handling/
treating of the machine will lead to a loss of guarantee and also any faults and damages
caused by undue force.
4. Any freight costs arrising in connection with the guarantee services have to be born by
the customer.
5. Guarantee services do not cause an extension of the guarantee time or the start of a
new guarantee time. The warranty for replaced parts ends with the guarantee time of
the whole unit.
6. We may, at our option, replace the machine rather than repair it.
7. Further claims, especially for damages, losses etc. outside the unit are excluded.
Other guarantee regulations may be valid outside the USA. Please check with your dealer!
If you should send the unit for service, do not forget to remove any liquid from the fluid
bottle.
For warranty service in North America contact:
Look Solutions USA Ltd.
1-800-426-4189
[email protected]

16
aLook Solutions product