Lorex VANTAGE LBC6050 Series User manual

Lorex Technologies Inc.
Copyright © 2011 Lorex Technologies Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product design,
specifications and prices, without notice and without incurring any obligation. E&OE
Cable Extension Options
Problem Solution
No Picture/Signal • Ensure your TV is on the correct input channel.
Common terms of an input channel: INPUT,
AV CHANNEL, LINE1, LINE2, AUX.
• If your camera is connected to a VCR/DVR,
ensure it is properly connected to your TV/
Monitor.
• Ensure connections are properly connected.
• Ensure the camera power supply is plugged
in.
Picture is too bright • Ensure your camera isn’t pointed directly at a
source of light (e.g sun or spot light).
• Slide the sunshade (bullet cameras only)
forward to block excess light.
• Move your camera to a different location.
Picture is too dark • If using during the day, the camera may not
be getting enough light. Slide the sunshade
backwards to let in more light. Check the
brightness and contrast settings of the device
your camera connects to (TV/Monitor/DVR).
Night Vision is not
working
• The night vision activates when light levels
drop. The area may have too much light.
Picture is not clear • Check the camera lens for dirt, dust,
spiderwebs. Clean the lens with a soft, clean
cloth.
• Make sure that the cable run is within the
limitations specified in the section ' Cable
Extension Options'
Bright spot in video
when viewing camera
at night
• Night vision reflects when pointing a camera
to a window. Move the camera to a different
location.
BNC connection does
not connect to my TV
• Use a BNC to RCA adapter at the end of the
extension cable.
Troubleshooting
Option Cable Type
1Regular BNC (sup-
plied with cam-
era)
180ft / 55m 3
2'RG59' or 'Coax'
or ' Coaxial' BNC
(sold separately)
300ft / 92m 5
3Lorex Universal
Cable
(sold separately)
300ft / 92m 3
Max. Cable
Run Distance
Notes:
1. For optimal performance, consider using option 2 or 3. Preference for using
the same cable type for the entire distance.
2. Cable run recommendation based on typical camera power consumption
(up to 500mA). For specialty cameras with higher current consumption,
maximum cable run may be reduced. Consider providing power to the
camera at the camera side rather then at the end of the extension cable.
3. Indicators that your cable run may be too long:
• Video is permanently Black & White (even during day time)
• Video is distorted
Max. # of
Extensions
Image Sensor 1/3" Sony Super HAD™ II
Video Format / Pixels
Horizontal Resolution
Video Output
IR / Night Vision Range
Field of View (diagonal)
Minimum Illumination
Termination
NTSC: 768(H)×494(V)
600 TVL
Comp. 1.0 Vpp @ 75ohm
60 Degrees
0 LUX (IR LEDs on)
Video: BNC Female
Power: Barrel Female
Lens / Lens Mount 6.0mm F2.0 / Fixed
Camera Specifications
Product Information
User Manuals
Quick Start Guides
Specification Sheets
Software Upgrades
Firmware Upgrades
www.lorextechnology.com
IT’S ALL ON THE WEB!
Extend the cable run for your camera up to 300ft or more
depending on the cable type used. See table below:
Operating Temperature 14°F ~ 122°F
(-10°C ~ 50°C)
Power Requirement 12V DC ±10%
Power Consumption 600 mA or 7.2W max
Weight (with stand) 1.6lbs. / 0.8 kg
47 IR LED/120 ft. (37 m)*
Environmental Rating IP 66*
4 in / 101mm 10.5 in/ 267mm
4 in /
101mm
*Not intended for submersion in water. Installation in a sheltered location recommended.
**IR Illumination range under ideal conditions. Objects at or beyond this range may be
partially or completely obscured, depending on the camera application.
SUPER RESOLUTION
IR NIGHT VISION CAMERA
LBC6050 Series
English Version 2.0
QUICK START GUIDE

Setup Diagram
Before Installing The Camera
• Decide to run the cables through the wall/ceiling (drilling required), or
along the wall/ceiling.
• If you run the cables along the wall/
ceiling, you must run the cable
through the cable notch on the base.
This will keep the camera base flush
to the wall/ceiling when mounted.
To install the camera:
1. Set the camera in the desired
mounting position and mark
holes for the screws.
2. Drill the holes, then feed the cable through the mounting
surface and mount the camera stand to the desired surface
using the provided screws. Make sure all three screws are
fastened tightly at the connection points.
3. Set the position and angle of the camera using the
provided Allen key.
Cable notch
ATTENTION - Test all connections and ensure the camera is working
correctly prior to permanent installation by temporarily connecting the
camera(s) and cable(s) to the viewing/recording solution.
1) Twist the ring to tighten / loosen
the stand connection. Adjust the
camera’s horizontal position.
2) Loosen the screw and adjust the
camera’s vertical position.
12
Contents
• 600TV line resolution for unmatched video quality
• Latest Sony Super HAD™ 2nd generation Image Sensor
• Advanced Noise Reduction for crystal clear Night Vision
• Improved recording storage efficiency by up to 30%
• Dual glass design prevents IR light reflection
• Long range Night Vision for far away night time
coverage
• Weatherproof, vandal resistant aluminum housing*
• Flexible camera design for wall and ceiling mounting
1 x Super Resolution Color Camera with cable pass-through stand
3 x Mounting screws / 1 x Allen key
1x 60ft. BNC/Power Extension Cable
1x BNC to RCA Adaptor
1x Power Adapter
Installation Tips
• Point the camera where there is the least amount of
obstructions (i.e. tree branches).
• Install the camera in a location that is difficult for
vandals to reach.
• Secure cabling so that it is not exposed or easily cut.
• Connect your system and cameras to a back-up power
supply. This ensures the system continues to record
during power outtages.
Installing The Camera
Warning / Caution
1. Read this guide carefully and keep it for future reference.
2. Follow all instructions for safe use of the product.
3. Use the camera within given temperature, humidity and voltage levels noted
in Camera Specifications.
4. Do not disassemble the camera.
5. Do not point the camera directly towards the sun or a source of intense light.
6. Use only the supplied regulated power supply. Use of a non-regulated, non-
conforming power supply can damage this product and voids the warranty.
7. The supplied extension cable is rated for surface mounting only.
Cables for in-wall / floor-to-floor installations are sold separately.
BNC to RCA Adapter
WARNING - A REGULATED UL/CSA APPROVED power supply is
REQUIRED for use with this camera. Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.
DVR/CCTV MONITOR
Video IN
TV/VCR
Video IN
Attach the included BNC to RCA adapter to connect the
extension cable to RCA inputs (i.e. for a TV connection).
BNC to RCA Adapter
Connecting The Camera
Features
Connect the BNC and
power connectors to the
camera.
Connect the BNC connector to
the video input of the monitor/
DVR, and connect the included
power connector to a power
adapter.
Male power connector
BNC Connector
To Camera: To Monitor/ DVR:
Female power connector
*Not intended for submersion in water. Installation in a sheltered location
recommended.