Lorex C581CB Series User manual

Need Help?
Visit us online for up-to-date software
and complete instruction manuals
Click on the Downloads tab
4
Visit lorex.com
Search for the model
number of your product
Click on your product
in the search results
3
2
1
Resources
C581CB_QSG_EN_R2
5MP HD Bullet Security Camera
• 5MP HD Bullet Security Camera
• Mounting Kit*
• BNC / Power Extension Cable*
• Power Adapter**
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use of the product and handle
with care.
• Use the camera within given temperature, humidity and
voltage levels noted in the camera’s specifications.
• Do not disassemble the camera.
• Do not point the camera directly towards the sun or a source
of intense light.
• Use only the supplied regulated power supply provided with
the product. Use of a non-regulated, non-conforming power
supply can damage the product and void the warranty.
• Periodic cleaning may be required. Use a damp cloth only. Do
not use any harsh, chemical-based cleaners.
• The supplied cable is rated for surface mounting only. Cables
for in-wall and floor-to-floor installations are sold separately
(CMR type). These and other cables are available at lorex.com.
• Point the camera where there is the least amount of
obstructions (i.e., tree branches).
• Install the camera where vandals cannot easily reach.
• Secure cabling so that it is not exposed or easily cut.
• This camera is rated for outdoor use. Installation in a
sheltered location is recommended.
* Per camera in multi-camera packs.
** A multi-camera power adapter that provides power to multiple
cameras or individual power adapters may be provided depending on
product configuration.
Copyright © 2019 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right
to modify product design, specifications and prices, without notice and without
incurring any obligation. E&OE. All rights reserved.
• For a full list of compatible recorders, visit lorex.com/compatibility
• Not intended for submersion in water. Installation in a sheltered
location recommended.
• This camera includes an Auto Mechanical IR Cut Filter. When the
camera changes between Day/Night viewing modes, an audible clicking
noise may be heard from the camera. This clicking is normal, and
indicates that the camera filter is working.
Quick Start Guide
English Version 2.0
C581CB SERIES
Package Contents
ATTENTION:
A REGULATED UL / CSA APPROVED power supply is REQUIRED for use
with this camera (included). Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.
Safety Precautions
Installation Tips
Dimensions
6.3” / 161mm
2.8” / 71mm
Disclaimers
www.lorex.com

Connecting the Cameras
Individual Power Adapter* Multi-Camera Power Adapter*
Connecting the Cameras
* Images for representation only
To install your camera:
1. Set the camera in the desired mounting position and mark
holes for screws through the camera base.
2. Drill the holes, then feed the cable through the mounting
surface or cable notch.
Installing the Camera
Extend the cable run for your camera depending on the cable type used.
Additional extension cables sold separately. See table below:
Connect the male power head
and the BNC connector to the
camera.
Connect the BNC connector
to a video input on your DVR.
Connecting the Camera
Cable Notch
C581CB_QSG_EN_R2
Power Adapter Types
A multi-camera power adapter that provides power to multiple cameras
or individual power adapters may be provided, depending on product
configuration.
Problem Solution
No picture / signal • The cameras are only compatible with certain
Lorex HD DVRs. For the full list of compatible
recorders, visit lorex.com/compatibility
• Ensure your TV or monitor is on the correct
input channel. Common terms for input
channels: INPUT, AV CHANNEL, LINE1, LINE2,
AUX.
• Ensure your DVR is properly connected to
your TV or monitor.
• Ensure connections are properly connected.
• Ensure the camera power supply is plugged
in.
Picture is too bright • Ensure your camera isn’t pointed directly at a
source of light (e.g., sun or spot light).
• Check the brightness settings of the DVR and
monitor.
• Move your camera to a different location.
Picture is too dark • Check the brightness and contrast settings
of the DVR and monitor.
Night vision is not
working
• The night vision activates when light levels
drop. The area may have too much light.
Picture is not clear • Check the camera lens for dirt, dust,
spiderwebs. Clean the lens with a soft, clean
cloth.
• Make sure that the cable run is within the
limitations specified in the section ‘Cable
Extension Options’.
• Remove the vinyl film from the camera lens
when your installation is complete.
Bright spot in video when
viewing camera at night
• Night vision reflects when pointing a camera
through a window. Move the camera to a
different location.
Troubleshooting
A. ROTATING THE ARM: Rotate the camera stand up to 360°.
B. BENDING THE ARM: Bend the arm of the camera up to 90°.
C. LEVELING THE CAMERA: Rotate the camera until it is level with
the viewing area, then tighten the adjustment screw.
ATTENTION:
Test your camera prior to selecting a permanent mounting location by
temporarily connecting the camera and cable to your DVR.
Before Installing the Camera
• Decide whether to run the cables
through the wall / ceiling (drilling
required) or along the wall / ceiling.
• If you run the cables along the
wall / ceiling, you must run the
cable through the cable notch on the
base. This will keep the camera base
flush to the surface when mounted.
Connect the female power
head to the included power
adapter.
Camera DVR
Male Power Female Power
Setup Diagram
BNC Video
12V DC Power
Camera
Extension Cable
Power Adapter
HD DVR
Cable Extension Options
Option Cable Type Max Cable Run
Distance
1BNC cable included with the camera 60ft (18m)
2‘RG59’ or ‘Coax’ or ‘Coaxial BNC’ Siamese
(Video and Power) 200ft (61m)
3‘RG59’ or ‘Coax’ or ‘Coaxial BNC’ (Video
Only)2800ft (242m)
NOTES:
1. The extension cable must be a single stretch of cable between the
DVR and camera. You cannot connect multiple extension cables to
each other.
2. For cable runs above 200ft (61m), you must connect the power
adapter directly to the camera, rather than at the end of the
extension cable.
3. Indicators that your cable run may be too long:
• Video is permanently black & white (even during day time).
• Video is unclear, soft, or distorted.
4. For more information on extension cables, visit lorex.com.
4. Use a Philips head screwdriver (not included) to loosen the
adjustment screw.
5. Adjust the postion of the camera as needed:
A
Adjustment Screw
3. Mount the camera stand
to the surface using the
provided screws. Make
sure all screws
are fastened tightly.
NOTE: Insert the
included drywall anchors
if you are mounting the
camera onto drywall.
6. Tighten the adjustment screw when finished.
7. Remove the vinyl film from the camera lens when your
installation is complete.
Drywall anchors (×3)
Mounting surface
Mounting screws (×3)
Camera
base
B
C