Lorex LW2301AC1 Series User manual

www.lorexcctv.com LW2301AC1 SERIES QSG_EN_R1 Page 1
CONTENTS:
Quick Start Guide
Digital Wireless Color
Camera with Stand
Wireless Antenna
for camera
Power Adaptor
for camera*
• Aim the Cameras to best optimize the viewing area:
Select a location for the camera that provides a clear
view of the area you want to monitor, which is free from
dust, and is not in line-of-sight to a strong light source
or direct sunlight.
• Avoid installing the cameras where there are thick
walls, obstructions, or interference (i.e. transformers,
microwave ovens or other electrical equipment)
between the Cameras and the Receiver.
• Select a location for the camera that has an ambient
temperature between 14°F~122°F (-10°C~50°C)
• Before starting permanent installation, have another
person hold the camera for you while you verify its
performance by observing the image on a monitor.
INSTALLING THE CAMERA
Before you install the camera, carefully plan where and how it will be
positioned, and where you will route the cable that connects the
camera to the power adaptor.
INSTALLATION WARNINGS
1. Carefully unpack the Camera.
2. Mount the stand to the wall:
• Mark the position of the
screw holes on the wall.
• Drill holes and insert the
drywall plugs as needed.
• Firmly attach the stand
to the wall using the
provided screws.
3. Attach the Antenna to the
Camera prior to mounting.
4. Place the camera in the
desired mounting position.
Tighten the thumbscrews
to secure the camera to the
Stand. Adjust the angle of
the camera until the
desired view is set.
*May not be exactly as shown
NOTE: AVOID INSTALLING IN A
LOCATION WHICH REQUIRES
THE WIRELESS SIGNAL TO PASS
THROUGH CEMENT, CONCRETE
AND METAL STRUCTURES. THIS
WILL REDUCE THE
TRANSMISSION RANGE.
Mounting
Hardware kit
COLOR DIGITAL WIRELESS INDOOR/OUTDOOR
ACCESSORY MOTION CAMERA
LW2301AC1 SERIES - QUICK START GUIDE
CAMERA OVERVIEW
1. PIR Sensor: Passive IR motion sensor for more accurate
motion recording.
2. Microphone: Built-in microphone underneath camera body.
3. Lens: Camera lens.
4. Night Vision IR: Night vision IR LEDs used for viewing in
complete darkness.
5. Pair: Pairing button.
6. Antenna: Wireless antenna.
7. Power Cable: Connect the included power adapter to the
cable extending from the camera.

www.lorexcctv.com LW2301AC1 SERIES QSG_EN_R1 Page 2
CONNECTING CAMERA POWER ADAPTOR
Connect one end of the camera Power Adaptor to the camera and the other end to an electrical outlet.
It’s all on the Web
For detailed setup information,
please refer to your User’s Manual.
For additional information, please
visit our website
www.lorexcctv.com/support
1. Press MENU on the wireless receiver or remote control.
2. From the Main Menu, select Pairing and press the
Enter button.
3. Select Camera 2, Camera 3 or Camera 4 and press the
Enter button.
4. Following the on-screen prompt, press the Pair button
on the rear panel of the camera. You have 30 seconds
to press the PAIR button on the camera. Once paired,
the camera will be immediately displayed on-screen.
NOTE: If you do press the Pair button on the camera during
the 30 second pairing window, repeat steps 1~4 to try the
pairing process again.
Pairing Button
ADDING THE ACCESSORY CAMERA TO YOUR SYSTEM
The Pairing Function assigns each camera to a different
channel on the wireless receiver (connect up to 4
Cameras), and is necessary for configuring additional
cameras. By default the camera that came with the
LW2301 system is assigned to channel no. 1.
NOTE: It is highly recommended to pair the Accessory
Camera to the Receiver before permanently mounting the
camera. For detailed information, please check the
owners manual for the LW2301 system available at
www.lorexcctv.com
Connect power adaptor to
local 120V AC power outlet
COLOR DIGITAL WIRELESS INDOOR/OUTDOOR
ACCESSORY MOTION CAMERA
LW2301AC1 SERIES - QUICK START GUIDE