Lovencare BP 6617 User manual

2-in-1 Lunar Swing
BP 6617
Read all instructions before assembly and use of
product. Keep instructions for future use.

Congratulations
Congratulations on purchasing your
new Love N Care Swing/Rocker.
In just a few steps you should be able to
assemble this unique product and have it
ready to meet your beautiful child :)
1.

WARNING:
Prevent serious injury or death:
WARNING:
NEVER leave child unattended.
WARNING:
ALWAYS use restraint system.
WARNING:
NEVER use for a child able to sit up unassisted.
FALL HAZARD: Child’s activity may move product.
SUFFOCATION HAZARD: Never use on a
soft surface (bed, sofa, cushion), as seat may tip over and
cause suffocation.
Use only on floor. Never use on an elevated surface.
- All plastic packaging and elements which are not a part of the bouncer set should be
removed before giving it to the child.
- The bouncer must be assembled by an adult only. The product should be checked by an
adult before every use.
The bouncer set includes small parts and should be kept away from babies before it is assembled.
- Never leave the child unattended. Never use for a baby who is able to leave the bouncer
on its own.
- Use in reclined position until your child is not able to hold up head unassisted.
- Do not use if your child is able to sit upright unaided or weighs more than 9 kgs.
- Never use on a soft surface (e.g. bed), as bouncer may tip over and cause suffocation.
- Never leave the bouncer on uneven or sloping surfaces.
- Never use this product on an elevated surface e.g. table - it is dangerous. Always use it
on the floor.
- This bouncer is not intended for prolonged period of sleeping. It does not replace a bed.
Should your child need to sleep, then it should be placed in a bed.
- Always use the restraint system while child is in the bouncer.
- Never lift the bouncer using a toy bar as a handle.
- Never lift or move the bouncer when the baby is inside.
- Never use the bouncer if there are any parts missing or broken. Never use any accessories or
replacement parts unless they are ones approved by the manufacturer. Regularly check the
condition of the bouncer.
- Keep bouncer away from open fire and other sources of heat.
- If the bouncer is not used for prelonged period of time - remove batteries. After dismantling
- keep parts away from babies.
IMPORTANT! Small parts are included in the box. Product must be assembled by an adult.
WARNINGS
NEVER place a child under 5 lbs. (2.26 kg) or over 20 lbs. (9 kg) in
the product.
- Please read this instruction manual carefully before using the bouncer and keep it together
with packaging for future reference.
- Swinging unit requires 4 x LR20 batteries 1,5 V (not included).
- This bouncer is intended for children weighing up to 9 kgs.
- Actual product may differ from image shown.
2.

Parts List
NO.
Content
1
Drive Box
2
Control Box
3
Rear Base Covers L+R
4
Position Adjustment Component
×
2
5
Backrest Tube
6
Footrest Tube
7
Seat Cover
8
Adapter (Option)
9
Spare Parts Bag
10
Toys
11
Seat base Frame
12
Swing Frame
13
Base Tubes L+R
14
Support Frame
3.
- Actual product and Parts may differ from images shown.
Please make sure all parts are included before
proceeding to assembly

Assembly
1. Push the socket of Control Box into the one of Drive Box parallelly according to Fig.1.
Ensuring the sockets of both boxes are corresponding and correctly inserted and both of
the two boxes shall be on the horizon after installation.
Fig.1
2. Assembling the Left and Right rear base covers on the base tubes with specified screws,
the rear base covers are in different pointing and with marker for correctly installation.
（Fig.2 No.1）
Join the support frame and the base tubes together, push the ends into the both base tubes
housing until the snap pins click and lock into place.（Fig.2 No.2）
Connect the support frame with the power unit assembly on the step 1.Push the free ends
together until the snap pins click and lock into place. (Fig.2 No.3)
Join the free ends of the power cables from the support frame and the drive box.
(Fig. 2 No.4)
3，将臂和主
Fig.2
4.

3. Join the swing frame into the corresponding housing of the drive box, fix with the given
screws of spare parts bag and ensuring to screw up. (Fig.3)
F
Fig.3
4. Separately push the backrest tube/footrest tube into the FRONT/BACK of the position
adjustment component holders until the snap pins click and ensure that it has locked into
place. (Fig.4)
5. Slide the seat cover on to the seat frame assembly. (Fig.5)
Fig.5
Fig.4
Fig.6
5.

6. Attach the seat base frame to the corresponding slot at each side of the seat cover.
Push the seat base frame into the lower end of the position adjustment component until
the snap click and lock into place. (Fig.6)
Fig.6
7. Join the completed seat into the U shape tube on the swing frame until the snap click and
ensure it is securely in place. (Fig.7)
Fig.7
6.

8. Hang the toys onto the toy plate. (Fig.8)
III. Operation
1. For batteries, remove the battery cover using a screwdriver with 4 pcs “D”batteries
（Not Supplied）. (Fig.9)
Fig.8
Fig.9
2. For Adapter (not supplied), plug into the connector at the back of support frame. (Fig.10)
Fig.9
Fig.10
7.

3. Correctly perform the functions according to the designation markers on the control box.
(Fig.11)
Fig.11
4. For playing more music/melodies from mobile phone, connect mobile phone with the
power cable from the mounting groove on the control box. (Fig.12)
5. Secure the baby to the Swing by fastening the buckles on the seat. (Fig.13)
Fig.13
Fig.12
Fig.13
8.

6. The product is a 2 in 1 design, the seat could be used as a Rocker when pull it up and out
from the swing. Please don’t leave the baby onto the seat when taking out. (Fig.14)
Fig.14
7. 3 reclining positions by the button on the seat assembly for option. (Fig. 15)
8. To use the seat as a Rocker in stationary mode, pull down the shiftable tube at the rear of
seat base frame. (Fig.16)
Fig.15
Fig.16
9.

9. Press the button at the back of the frame to fold or extend the product. (Fig.17)
Fig.17
10.

BATTERIES REPLACEMENT
- Battery chamber is located on the bottom of base support front tube / on the top of Rainbow lights.
- Unscrew battery cover with phillips screwdriver. Remove cover and place 4 xLR20 batteries into
the battery chamber (g.12.)
- Rainbow lights - Operation by 3x LR6 ( AA ) batteries (g.14.)
- Close the battery chamber and tighten the screw.
ALL ACTIONS ASSOCIATED WITH BATTERY REPLACEMENT MUST BE PERFORMED BY AN ADULT
1. Insert the batteries into the chamber indicated on the packaging or the product itself. In order to insert the batteries to the chamber,
unscrew the securing cover and place the batteries in line with the polarity. After the batteries are inserted, screw the cover back on.
2. In order to take the batteries out, unscrew the securing cover, remove the batteries and close the cover again.
3. Batteries which are not suited for charging are not to be charged.
4. Chargeable batteries can be charged under adult supervision.
5. Chargeable batteries should be removed from the product before charging.
6. Batteries should be inserted maintaining proper polarity.
7. Do not mix together dierent types of batteries or new and used batteries.
8. Only use batteries of a recommended type or equivalents.
9. Depleted batteries should be immediately removed from the product.
10. Do not short circuit the battery clamps.
11. The product uses replaceable batteries.
12. The product cannot be connected to more power sources than recommended.
13. Used batteries should be thrown into specially marked containers intended
to collect used batteries and used electronic equipment.
CLEANING AND MAINTENANCE
- Keep the product in dry places. In order to keep the product attractive - avoid prelonged sun exposure.
- Check condition of the bouncer regularly. Before each use check if it is assembled regularly.
- Use only parts recommended and provided by manufacturer.
- Clean the bouncer regularly.
- In order to clean plastic parts and tubes - use damp cloth.
- Padding can be hand washed with a bit of delicate soap. Do not bleach!
- Fabric of the seat pad can be cleaned with a damp cloth.
11.

WARRANTY AGAINST DEFECTS
All Love N Care products are guaranteed for twelve months from the date
of purchase. Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
This covers against faults which develop through faulty materials and
workmanship.
Misuse, accidental damages,normal wear and tear or neglect are not covered.
If a fault becomes apparent, please return the item to the store of purchase with
your receipt. You must inform the store what the defect is. We will then arrange
for its repair or it will be assessed for replacement as expediently as possible.
The benefits of this warranty are in addition to other right and remedies under
the law in relation to the goods or services to which this warranty relates.
If you are unable to return the item to the store of purchase, you can contact
Love N Care on free call 1300 732 599.
Where you send the product directly to the manufacturer then you may
be liable for the costs of transportation to and from Love N Care.
Love N Care will meet the reasonable expenses incurred by a consumer in
a making a warranty claim. You can claim expenses incurred in making a
claim by contacting our customer service team on 1300 732 599 or by email
at [email protected]
12.

Head Office:
Love N Care Pty Ltd.
297-299 Canterbury Rd, Revesby
NSW 2212 Australia
Contact No: 02 9774 4655
Fax: [phone]
Email: [email protected]
www.lovencare.com.au
Contact Us