Lovencare X-Factor BP 9001 User manual

Instruction Manual
“ X-Factor ” Stationary Centre
IT EM : BP 90 0 1
!IMPORTANT:
PLEASE READ INSTRUCTIONS
CAREFULLY AND KEEP FOR FUTURE REFERENCE!

2
WARNING
To prevent serious injury or death
Use only for a child who is able to hold head upright unassisted and who is not able to walk or
climb out of product.
Never leave child unattended. Always keep child in view while in product.
Never use near steps, pools, hot surfaces or areas that may be hazardous to a child. Product may
move during use.

Strings can cause strangulation! DO NOT place items with a string around child’s neck, such as
hood strings or pacif er cords. DO NOT suspend over product or attach strings to toys.
IMPORTANT! PLEASE KEEP THESE
INSTRUCTIONS FOR FUTURE REFERENCE
Please read these instructions before assembly and use of this product.
Adult assembly is required. Tool needed for battery installation:
Phillips screwdriver(not included).
Requires two “AA” (LR6) alkaline batteries (not included) for toy operation.
use only for a child:
-who is able to hold head up unassisted.
-who is not able to climb out.
-who weighs less than 25 lbs.(11.3kg) and is less than 32 inches (81cm) in height.
This baby walking frame should be used only for short periods of time ( e.g.20 mins. ).
Do not use replacement parts other than those approved by the manufacturer or distributor.
WARNING: Do not use this jumping walker as a swing.
The child will be dangerous of play nearby jumping walker.
Keep child in the middle of seat correctly.
Cleaning:
Clean with a damp sponge or cloth and mild detergent. Do not use abrasives or bleach.

3
PARTS
Plush Arch Toy x1
Arch Toy x1
Music Tray x1
Seat Ring x1
Seat Pad x1
Spinner Ball Toy x1
Base x2
A
B
C
D
AB
CD
Spinner Toys x2
Bouncer x1
U Frame
U Frame
X Frame x2
A
C
TOOL NEEDED: Phillips Screwdriver

4
1-2
3
B
A
CD
STEP 2 STEP 1
b
b
a
a
a
b
1. Put the X Frames and
the base together as
shown in the diagram.
2. Push the button in the
end of the poles inward
(a), then slot the poles
fully into base (b).
3. Ensure that the buttons
are protruding through.
Slot U Frame on the
bouncer onto the ends
of the X Frame until it
rests on the buttons.
Push the button inwards
(a), then slot the poles
fully into the base (b).
Ensure that the button
are protruding through.

5
STEP 4 STEP 3
1. Slot the Spinner ball toy,
into the round holes on
the bouncer, see diagram.
2. Push into the holes until
the studs on the ends of
toy lock over the housing
on the underside of the
bouncer and cannot be
Slot the two spinner toys into
the round holes in the end of
the bouncer, see diagram.
Push the spinner toys into the
holes until the studs on the
ends of the spinner toys lock
over the housings on the
underside of the bouncer

STEP 6 STEP 5
6
battery
battery
Slot the plush arch toy into the
round holes on the main tray,
see diagram.
Make sure both lock hooks snap
into the lock hook holes.
Before fitting the music insert you will
need to fit the batteries.
Unfasten the screw in the battery cover
using a X-head screwdriver.
Insert two ‘AA’ batteries, ensure that the
batteries are fitted the correct way
round.
Refit the battery cover and tighten the
screw.

7
STEP 8 STEP 7
1
2
To assemble music tray
slot the arch toy into the
music tray as shown.
1. Slot the music tray on
the bouncer, see diagram.
Ensure both front locks
hook into the openings.
2. Push down on the back
of music tray. Ensure that
both back locks are
securly in place.

STEP 9
Battery safety information
Hint: We recommend using alkaline batteries for longer battery life.
Protect the environment by not disposing of this product with household waste check your
local authority for recycling advice and facilities.
Fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:
In exceptional circumstances may leak.

(carbon-zinc) or rechargeable (nickel-cadmium).
Insert batteries as indicated inside the battery compartment.
Remove batteries during long periods of non-use.Always remove exhausted batteries from
the product. Dispose of batteries safely.Do not dispose of product in a fire. The batteries inside
may explode ot leak.
Never short-circuit the battery terminals.
Use only batteries of the same or equivalent type as recommended.
Do not charge non-rechargeable batteries.
Remove rechargeable batteries from the product before charging.
If removeable, rechargeable batteries are used, they are only to be charged under adult
supervision.
8
Slide the switch on the back
of the music insert along for
, quiet music or
loud music.
Pr
the front of the music insert
rent tunes.
QuietLoud

STEP 10
1
2
3
4
1. Pull the crotch section of the
seat pad outwards, the warning
label will be at the back and the
adjustment strap for the seat
pad will be at the bottom.
2. Slot the seat pad onto the seat
ring so that the and on the
warning label are aligned with
the and on on the back of
the seat ring.
3. Hook the plastic tabs with the
holes in on the seat pad over the
tabs on the seat ring.
4. The seat pad is now attached to
the seat ring.
IMPORTANT: Check that the seat
pad is correctly fitted to the seat
ring.
9

STEP 11
10
2
3
1
1. Slot the assembled seat
into the hole in the middle
of the bouncer.
2. While holding the
sides of the bouncer, push
down on the seat ring
until the clips on the seat
ring lock over the edge of
the bouncer.
3. Turn the bouncer over
and check the all of the
six clips have locked over
the edge of the bouncer.
Also pull up on the seat
to ensure that it will not
.
Once fitted the seat will
rotate freely.