LOWE'S F00019 User manual

Working hours: Mon - Fri 9:00 a.m - 16:00 p.m. EST [email protected]
Item Number: F00019 - DINNING SET
CLEANING INSTRUCTIONS: CLEAN USING SOFT CLOTH PAGE 1 OF 5 MADE IN VIET NAM

Working hours: Mon - Fri 9:00 a.m - 16:00 p.m. EST [email protected]
CLEANING INSTRUCTIONS: CLEAN USING SOFT CLOTH PAGE 2 OF 5 MADE IN VIET NAM
Item Number: F00019 - DINNING TABLE
Thank you for purchasing this product. Please take time to read and follow the instructions below. Check that you have
all parts and hardware before assembly. Parts apparently missing are often found in the packing materials. If you do
not have all the parts listed, have your dealer contact us and they will be sent to you immediately.
It is recommended to install protective pads under all legs and supports to avoid damage or scratches when
placing furniture on a wood floor or other hard surface, and to limit indentation and prevent discoloration if
placing on carpet.
Do not tighten bolts until completely assembled.
PART LIST
A
B
C
D
FACE DOWN
TABLE TOP
MOUNTING PLATE
UPPER LEG
LOWER LEG
1PC
4PCS
1PC
1PC
HARDWARE LIST
1
2
3
4
5
BOLT 5/16"-18x3" 1PC
BOLT 5/16"-18x1-1/2" 16PCS
SPRING WASHER
5/16"x11/32"x11/16"x1/16"
ALLEN KEY 1"x2-1/3"
FLAT WASHER
5/16"x21/61"x3/4"x5/64"
17PCS
17PCS
1PC

Working hours: Mon - Fri 9:00 a.m - 16:00 p.m. EST [email protected]
Item Number: F00019 - DINNING TABLE
Step 1/
C
D
1
3
4
5
Step 2/ B
2
3
4
5
FACE DOWN
Step 3/
A
2
3
4
5
CLEANING INSTRUCTIONS: CLEAN USING SOFT CLOTH PAGE 3 OF 5 MADE IN VIET NAM

Working hours: Mon - Fri 9:00 a.m - 16:00 p.m. EST [email protected]
Item Number: F00019 - CHAIR
CLEANING INSTRUCTIONS: CLEAN USING SOFT CLOTH PAGE 4 OF 5 MADE IN VIET NAM
Read instructions carefully prior to assembly.
Thank you for purchasing this quality product. Check carefully for small parts which may come loose during shipment.
Remove all components from pack and place top down on soft surface such as carpet or cloth to prevent scratching
the finish. Identify and count all parts as specified below.
Note: need to be set on a level surface prior to tightening all the bolts. Once all the bolts and nuts are finger tightened,
set chair on level surface to tighten bolts.
HARDWARE LIST
A
PART LIST
1
2
3
2PCS
2PCS
4PCS
No. Description Sketch Q'ty
CHAIR BACK
SEAT CUSHION
FRONT LEG
No. Description Sketch Q'tySize
B
C
D
E
F
G
H
Allen Bolt
Allen Bolt
Lock Washer
Flat Washer
Hex Nut
Allen Key
Straight Allen Key
Open Wrench
5/16"*35mm
5/16"*75mm
5/16"
5/16"*19mm
5/16"*12mm
4mm
4mm x 4"L
12mm
6PCS
8PCS
22PCS
22PCS
8PCS
1PCS
1PCS
1PCS
Step 1: Attach seat frame to chair back by securing the
Flat Washer (D), Lock Washer (C) and Allen Bolt (A) onto
back rail.
Hand Tight only at this moment
Step 2: Attach seat frame to chair back by securing the
Flat Washer (D), Lock Washer (C) and Allen Bolt (B) onto
back rail.
Hand Tight only at this moment
Step 1/ Step 2/
A
C
D
F
1
2
1
2
B
C
D
F

Working hours: Mon - Fri 9:00 a.m - 16:00 p.m. EST [email protected]
Item Number: F00019 - CHAIR
CLEANING INSTRUCTIONS: CLEAN USING SOFT CLOTH PAGE 5 OF 5 MADE IN VIET NAM
Step 3/
Step 3: Attach the front leg to the corner of the seat frame, tighten the front leg with Flat Washer (D), Lock Washer (C)
and Hex Nut (E)
Step 4: Place Chair on flat surface and adjust legs so that chair is level and does not wobble, Tighten all the bolts with
Allen Key (F) provided, Do not to over tighten.
1
2
3
H
E
C
D
Step 4/