Loxit Lapbank TL 16 User manual

Loxit Limited, First Avenue, Poynton Industrial Estate, Poynton, Cheshire, UK. SK12 1YJ
www.loxit.com ꞁ [email protected]m ꞁ [phone]
Lapbank TL 16- 6730
WARNING
•Children must be under surveillance to ensure that they do not play with this piece of electrical
equipment.
•The product is shipped fully assembled, if the unit is being stored do not double stack.
•Ensure that all casters are released from their brakes and are running freely when being moved.
•This unit is not designed for rough terrain.
•Please treat sympathetically avoiding kerbs or changes in level and being especially careful when
changing floor surfaces or crossing sloping areas. Take your time. If in doubt ask a second person
to assist you.
•Ensure the outlet socket the trolley is connected to is easily accessible
•The weight of the trolley exceeds 25kg, Do not attempt to lift the trolley.
Maintenance Instructions
•There are no user maintenance or adjustment points on this machine. Simply clean dust and dirt
from the outside of the unit and inspect for damage or breaks.
•Cleaners and disinfectants must not be highly alkaline or acidic.
•The user should visually check the equipment for signs of wear or misuse before each time of
using and for the security of the screen or any accessories.
•The condition of electrical cables and plugs should be checked for wear or abrasion before use.
•In addition, the equipment should be visually inspected in more detail every three months to
ensure that the unit is functioning properly and if it is not the user should report this to the
manufacturer for advice or for the return of the unit to base for repair.
•Incidences of misuse must be reported immediately and the unit placed out of commission.
•All repairs to the unit must only be carried out by Loxit.
•The warranty is only valid in so far as the equipment has been used and maintained correctly
and has not been tampered with.
•Violent treatment will invalidate the warranty.
•During operation if the unit makes any unusual noises or smells turn off the power supply at the
mains immediately.
•Ambient temperature range +5deg C to +40 deg C.
Safety
Before Charging Please Check:
1. The wall socket is switched on
2. The RESET button on the RCD is pushed in
3. The red neon indicator switch on the power strip is switched on and lit if applicable, or the rocker
switch in the case of ChargeConnect products.

Loxit Limited, First Avenue, Poynton Industrial Estate, Poynton, Cheshire, UK. SK12 1YJ
www.loxit.com ꞁ [email protected]m ꞁ [phone]
4. The IEC lead is plugged into the IEC inlet and the IEC Inlet switch is turned on with the neon indicator
light illuminated.
5. The low voltage power leads are firmly connected to the power source (device transformer or
ChargeConnect) and the device.
Lapbank TL products must be connected to an RCD protected earthed mains supply when charging.
Power Rating:
230v –50 Hz –10 amps. TOTAL NOT TO EXCEED 10 amps. OUTPUT –230V AC –10 amps.
Fuses located within the plug and Power inlet IEC block are the only user serviceable parts within the
unit, any warranty and service issues should be referred to your supplier.
Power input IEC block fuse: Fast Blow Glass Fuse, 10A, 250V (F10AL250V)
Mains cable plug fuse: 10A BS1362 Fuse
In the event of the mains plug or lead being damaged, the unit should not be used until a new plug or
lead has been fitted by a competent person. The old plug or lead must be safely disposed of.
THE MAINS INPUT TO THE LAPBANK TL TROLLEY MUST ONLY BE PLUGGED INTO AND REMOVED FROM
A SWITCHED MAINS PLUG SOCKET WHICH IS TURNED OFF.
Please ensure the mains input cable is unplugged before unlocking the wheels (if applicable) and moving
the trolley.
DO NOT DROP THE RCD PLUG, it contains sensitive electronics and may become damaged.
Mains input cables must be inspected daily for damage and wear.
If any fault or damage is found with any mains input cable, remove all power sources and stop using
immediately. Contact Loxit Limited on [phone] for a replacement cable.
Visit www.loxit.com for contact details or sal[email protected]m to e-mail.
UNDER NO CIRCUMSTANCES SHOULD REPAIRS BE MADE TO THE MAINS INPUT CABLE.
•This Laptop storage and charging product must only be used by a competent adult and must not
be used if this can not be assured.
•If you are in any doubt please refer to your Health and Safety Co-ordinator and/or Health and
Safety Manual for guidance.
•This product requires PAT testing at maximum 12 monthly intervals.
•Portable Appliance Testing- This unit must only be earth bond and insulation tested using the IT
settings on any PAT tester.
•WEEE Directive- When the unit becomes redundant it must be disposed of in compliance with
the WEEE directive 2005.

Loxit Limited, First Avenue, Poynton Industrial Estate, Poynton, Cheshire, UK. SK12 1YJ
www.loxit.com ꞁ [email protected]m ꞁ [phone]
1. Unfasten the charge compartment hatch
by removing the three M5 bolts indicated.
2. Open the hatch around 45 degrees and unhook the hatch from the trolley.
3. Unlock and open the laptop compartment.
Cabling instructions

Loxit Limited, First Avenue, Poynton Industrial Estate, Poynton, Cheshire, UK. SK12 1YJ
www.loxit.com ꞁ [email protected]m ꞁ [phone]
5. Repeat step 4 for the remaining transformers and charging leads.
6. Before replacing the cover check all plugs
are fully inserted into the power strips and
transformers.
The charge hatch should now be hooked
back in place over the protruding bolts at
each side of the compartment.
4. Place the first transformer on the angled
tray, the transformer can be secured in
place using a Velcro strap or cable tie.
Grommet
Cable restraint
cutout
Transformer
Pass the charge cable through the
grommet into the laptop
compartment, ensure there is enough
cable to plug into your device.
Any spare cable can be coiled and
then restrained using a cable tie
passed through the cutout above the
transformer.
Plug the transformer into the power
strip, coil any spare cable in bottom of
the compartment or below the
transformer and secure with a cable
tie.
Power strip

Loxit Limited, First Avenue, Poynton Industrial Estate, Poynton, Cheshire, UK. SK12 1YJ
www.loxit.com ꞁ [email protected]m ꞁ [phone]
7. Secure the charge hatch using the two M5 bolts
removed in step 1.
8. Your laptops can now be loaded into your Lapbank and plugged
in. Once the laptops are in place the door can be closed and
locked if needed, be careful that no cables are trapped when
opening and closing the door.
9. To begin charging plug the IEC lead into the power socket at the side of the
trolley and into a mains socket.
Charging/operating instructions
10. When moving the trolley, the power cable can be coiled and
stored in the recessed area where the power socket is located.